

Sensor board
System for reading/writing temperature sensors
- Size
- 65 × 137 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 99
- Nets
- 60
- Pads
- 376
- Tracks, vias
- 1,130, 53
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 16 Jun 2014
- Updated
- 17 Sep 2014
Overview
Sensor board is an open-source printed circuit board by nEDM-TUM, from the nEDM-TUM/Temperature-Sensor-System repository on GitHub. It is a 2-layer board of 65 × 137 mm with 99 parts on 60 nets, routed with 1,130 tracks and 53 vias.
It is built around the ATMEGA88A-AU and LM7805. Its parts include 34 resistors, 32 capacitors, 10 ICs, 10 connectors and 5 diodes. It belongs with the sensors and measurement boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA88A-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 512Byte 8 Bit 8KB AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM7805
TO-2630℃~+125℃ 1 1A 20V 2V 42uV 5V 62dB@(120Hz) 8mA Fixed Over Temperature Protection、Short Circuit Protection Positive TO-263 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdTemperature-Sensor-System
Sensor network system built for the nEDM experiment.
Features
- Both temperature and humidity sensors can be connected at any sensor socket. The sensor type will be automatically detected.
- High temperature and humidity accuracy: Temperature sensors are calibrated to ±0.1K and the humidity sensors to ±1.8%rH.
- A high number of connected sensors is supported. Currently 44 sensors are in use, however the system is designed to support at least 100 sensors and still be able to fulfill a sampling rate of 1Hz. If the sampling rate is allowed to be slower, up to 960 sensors are possible to share one Ethernet connection.
- The system supports a fast sample rate of at least 1Hz.
- We achieved a relatively low cost per sensor. The cost per sensor module is mostly defined by the sensor chip alone, which is about e7 for a precision temperature sensor and about e20 for a high quality humidity sensor. The cost for the printed circuit board and required components is less than e4 per board.
- Measurement results can be forwarded via TCP/IP to a CouchDB server, which is able to record the measurement data from all connected sensors.
- The sensor network provides a TCP/telnet user interface, for controlling and viewing of network parameters. This allows easy configuring and debugging of the system.
- Most of the system parameters like sampling rate or database IP addresses and insert functions are configurable at runtime.
- Plug and Play is supported for adding and removing sensors or even control units during runtime.
Directory structure
.
+-- casings // 3D CAD files for 3D printer
| +-- adapter
| +-- arduino
| +-- cable_clamp
| +-- collector
| +-- humidity
| +-- temperature
+-- circuit_boards // Circuit schematic diagram and
| | // PCB schematic files created using KiCad
| +-- 3x127_254_adapter // A PCB chip adapter,
| | // used for breadboard debugging
| +-- 4x127_254_adapter // A PCB chip adapter,
| | // used for breadboard debugging
| +-- arduino_adapter
| +-- humidity
| +-- kicad_library // Footprint and Component
| | // library files for KiCad
| +-- order // PCB assembly, which was sent to
| | // Fischer Leiterplatten for production
| +-- sensor_board
| +-- so8_breakout // A PCB chip adapter,
| | // used for breadboard debugging
| +-- temperature_boardTips for developers
- To prevent EEPROM from being corrupted on power cycles, the AVR integrated brownout detection should be enabled.
- To allow EEPROM storage to stay intact after reprogramming, set the corresponding fuse bit.
- As Arduino fuses are not possible to be programmed via the default Arduino programmer (using the Arduino boot loader), we removed the boot loader and use the ISP connector for programming.
- To not overload the voltage regulator, especially when driving multiple boards one should consider, that a significant portion of power is used to drive LEDs. So turning the LEDs off during normal operation will prevent overheating.
- When debugging and programming devices of the sensor network, one has to be very careful, to not provide different power sources, as this might cause unexpected results, which can lead to damage of the sensor network, as well as connected computers. By default the USBasp programmer provides the system with 5V power.
- Our makefiles currently do not support automatic detection of file dependencies, and source files to be compiled. All source files have to be specified explicitly and if changes to header files are made, a ’make clean’ should be performed before compiling the program.
- Be careful, when using the USART line or similar for generating debugging output. Transmitting debugging information takes relatively long time and might influence the system heavily, especially, when debugging timing critical code. LEDs or GPIO pins with an oscilloscope provide a faster but more complex way for debugging.
###For more details about our project, please read the report document. ### Its tex file and needed images can be found in the folder report. You can use make to compile the document.
Parts
99| Qty | Value | Footprint | References |
|---|---|---|---|
| 25 | 100n | SM0603_big | C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C25, C26 +9 |
| 16 | 22k | SM0603_big | R10, R11, R12, R13, R14, R15, R16, R17, R22, R23, R24, R25, R26, R27, R28, R29 |
| 8 | 120 | SM0603_big | R18, R19, R20, R21, R30, R31, R32, R33 |
| 8 | ST485 | st485 | U2, U3, U4, U5, U6, U7, U8, U9 |
| 5 | 150 | SM0805_big | R2, R3, R4, R5, R8 |
| 3 | 10u | SM0805_big | C1, C23, C24 |
| 3 | VAL** | m3_loch | m3_loch, m3_loch, m3_loch |
| 2 | 10k | SM0603_big | R1, R9 |
| 2 | 22p | SM0603_big | C3, C4 |
| 2 | 2k2 | SM0603_big | R6, R7 |
| 1 | 0 | SM0805_big | R34 |
| 1 | 100nF | SM0603_big | C6 |
| 1 | 12Vin | LPV_Stiftleiste_2pol | P5 |
| 1 | 20MHz | HC-49_quarz_big | X1 |
| 1 | 330nF | SM0603_big | C5 |
| 1 | 5Vin | LPV_Stiftleiste_2pol | P9 |
| 1 | ATMEGA88A-A | TQFP32 | IC1 |
| 1 | HOHLBUCHSE | hohlbuchse_475_17 | P6 |
| 1 | ISP | wannenstecker_2x5_rm254 | P8 |
| 1 | LED1 | SM0603_big | D1 |
| 1 | LED2 | SM0603_big | D2 |
| 1 | LED3 | SM0603_big | D3 |
| 1 | LED4 | SM0603_big | D4 |
| 1 | LED_POW | SM0603_big | D5 |
| 1 | LM7805 | lm7805_lying | U1 |
| 1 | RJ45_8P8C_8FACH | RJ45_8P8C_8x | J1 |
| 1 | SCHALTER_2POL | DIP_Schalter_2pol | SW2 |
| 1 | SW1 | Taster_6mm | SW1 |
| 1 | SW_RESET | Taster_6mm | SW3 |
| 1 | Shield | m3_scheibe | P2 |
| 1 | UART | Stiftleiste_4x1 | P1 |
| 1 | Vccin | LPV_Stiftleiste_2pol | P7 |
| 1 | i2c_chain | wannenstecker_2x3_rm254 | P4 |
| 1 | i2c_pow | wannenstecker_2x3_rm254 | P3 |
| 1 | pow_sel | Stiftleiste_3x1 | K1 |
More from nEDM-TUM/Temperature-Sensor-System
8- 2 layers200 × 330 mm

- 2 layers200 × 164.9 mm

Order4 notent
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
306 parts - 2 layers100 × 20 mm

Humidity board
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
25 parts - 2 layers60 × 66.5 mm

Arduino adapter
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
15 parts - 2 layers20 × 76 mm

Temperature board
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
13 parts - 2 layers15.7 × 10.7 mm

- 2 layers9.9 × 8.1 mm

3x127 254 adapter
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
2 parts - 2 layers8.1 × 10.7 mm

4x127 254 adapter
nEDM-TUM/Temperature-Sensor-System
System for reading/writing temperature sensors
2 parts
Similar boards
- 2 layers41.4 × 36.1 mm

- 2 layers85.1 × 62.2 mm

Mic extension board
StoneRose35/cortexguitarfx
guitar effects processor implemented on various arm cortex platforms
75 parts146 - 2 layers

- 2 layers27.5 × 0 mm

Thermocouple
Miceuz/thermocouple-modbus
Thermocouple frontend accessible via industrial modbus protocol
75 parts2 - 2 layers99.6 × 99.6 mm

Karabas nano revJ
Vakon84/karabas-nano
ZX Spectrum compatible machine with real Z80 CPU and all logic inside the CPLD Altera EPM3256ATC144 (or EPM7512).
162 parts1WTFPL - 2 layers65 × 107.5 mm

- 2 layers22.4 × 29.8 mm

- 4 layers70 × 89.2 mm

Questions
How big is the Sensor board PCB?
It measures 65 × 137 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Sensor board use?
99 parts, built around the ATMEGA88A-AU and LM7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sensor board KiCad files?
From the nEDM-TUM/Temperature-Sensor-System repository on GitHub, at the commit this page was made from: the board is circuit_boards/sensor_board/sensor_board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sensor board design in my own project?
Its repository states no licence, so its author keeps all rights: ask nEDM-TUM before reusing the design.