

- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 39
- Pads
- 101
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 30 May 2025
- Updated
- 10 Jun 2025
Overview
PPG is an open-source printed circuit board by nathanos01, from the nathanos01/BME_Projekt_PCB repository on GitHub. It is a 2-layer board with 33 parts on 39 nets.
It is built around the SFH 7072, ADPD7000BCBZR7 and LP5910-1.8YKAR, with the DMP2045UQ-7 among its other parts. Its parts include 9 capacitors, 8 connectors, 5 resistors, 3 ICs and 1 diode.
Main components
4SFH 7072
DFN-12(3.9x7.5)DFN-12(3.9x7.5) Human Body Sensing Sensor ROHSOSRAM Opto SemiconHuman Body Sensing SensorADPD7000BCBZR7
WLCSP-36(2.6x2.8)-40℃~+85℃ 0.3uA 2.7V~3.6V 9000Hz 9000Hz 90dB 960kHz、1MHz Multiplexers、Simultaneous sampling control SPI WLCSP-36(2.6x2.8) Analog Front End (AFE) ROHSAnalog DevicesAnalog Front End (AFE)LP5910-1.8YKAR
DSBGA-4DSBGA-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsUncategorisedDMP2045UQ-7
SOT-23-3-55℃~+150℃ 1 P-Channel 1.2W 1V 20V 4.3A 45mΩ@4.5V 6.8nC 634pF 66pF 81pF SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
README.mdBME_Projekt_PCB
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | Conn_01x01_Pin | Connector_Wire:SolderWire-0.1sqmm_1x01_D0.4mm_OD1mm | J2, J3, J4, J8, J9, J10, J11, J12 |
| 5 | 10u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3, C4, C5, C6, C9 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2, C7, C8 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4 |
| 2 | 47 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 70 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | ADPD7000BCBZR7 | ADPD7000:CB-36-11_ADI | U1 |
| 1 | DMP2045UQ-7 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | D_Zener | Diode_SMD:D_0603_1608Metric | D1 |
| 1 | Fuse | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | LP5910-1.8YKAR | LP5919:YKA0004ACAC | U2 |
| 1 | SFH_7072 | SFH_7072:XDCR_SFH_7072 | U3 |
| 1 | Varistor | Varistor:VC | RV1 |
More from nathanos01/BME_Projekt_PCB
1- 4 layers20 × 12.5 mm

Similar boards
- 2 layers35.4 × 70.6 mm

PCB ESP32
maticas-tech-sas/maticas-data-logger
Want to send measurements back to a server through HTTP or MQTT? This is about it along with the PCB design, 3D box and support for data storage with maticas API
45 parts1 - 2 layers101.1 × 60.5 mm

DATALOGGER02
mlab-modules/DATALOGGER02
Arduino based data logger with LoRa IoT interface.
161 partsGPL-3.0 - 4 layers135 × 86.8 mm

Line following robot board
Pavich-3/line-following-robot-board
Line-following robot board in KiCad PCB (STM32F0)
73 parts - 6 layers

Pc healthypi move sensor v9
Protocentral/healthypi-move-hw
Hardware files for the HealthyPi Move
124 parts160MIT - 2 layers95 × 79 mm

- 6 layers21 × 36 mm

PPG Watch
gavin4d/PPG-Watch
Smart watch with a photoplethysmography analog front end and e-paper display
89 parts - 2 layers24.5 × 25 mm

Sfh7072 breakoutboard
lamikr/hrm_breakoutboards
HRM related small pcb breakoutboards to help testing some components one by one.
12 parts - 2 layers65 × 30 mm

Rgb to hdmi
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
33 parts1kGPL-3.0
Questions
What parts does the PPG use?
33 parts, built around the SFH 7072, ADPD7000BCBZR7, LP5910-1.8YKAR and DMP2045UQ-7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PPG KiCad files?
From the nathanos01/BME_Projekt_PCB repository on GitHub, at the commit this page was made from: the board is PCB/PPG/PPG.kicad_pcb and its schematic PCB/ECG/ECG.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PPG design in my own project?
Its repository states no licence, so its author keeps all rights: ask nathanos01 before reusing the design.