Skip to the content
4 layers56.4 × 20.3 mmRegulator, the printed circuit board in 3D

Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply…

Size
56.4 × 20.3 mm
Copper layers
4
Thickness
1.6 mm
Parts
34
Nets
12
Pads
112
Tracks, vias
375, 61
Pours
8
Routed
Yes
KiCad
KiCad 4
Created
16 Aug 2014
Updated
17 May 2021

Overview

Regulator is an open-source printed circuit board by nacs-lab, from the nacs-lab/yyc-data repository on GitHub. It is a 4-layer board of 56.4 × 20.3 mm with 34 parts on 12 nets, routed with 375 tracks and 61 vias.

Its parts include 22 capacitors, 6 resistors, 2 ICs and 2 connectors. It belongs with the power boards of this library.

README

designs/cmr_link/README.md

Orientations

Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply connectors on the breakout board. Also the side that is farther from the FPGA board/chip.

When looking from the front side of the board with the 2x30 connector on the bottom and the camera link connector on the top, the PIN 1 of the 2x30 connector is on the bottom left of the board and it should be connected to the ground on the breakout board as well as all other odd number pins on this connector. Pin 60 of the connector is VCC3V3 from the FPGA board.

Camera link pin assignments

According to Andor's document, each pixel is a 16bit little endian integer, and according to the standard Port A and Port B should be used in this case.

Microstrip

Trace width: 10 mil

Trace separation: 6 mil

Trace thickness: 1.7 mil

Dielectric thickness: 11.9 mil

Relative dielectric constant: 4.5

Differential impedance: 100.4 Ohm

Useful documents

Parts

34
QtyValueFootprintReferences
810uCapacitors_SMD:C_0603C3, C4, C5, C6, C11, C12, C17, C18
60.1uCapacitors_SMD:C_0805C9, C10, C13, C14, C21, C22
61.5uCapacitors_SMD:C_0805C7, C8, C15, C16, C19, C20
20.1Resistors_SMD:R_0603R1, R2
2100uCapacitors_THT:CP_Radial_D10.0mm_P5.00mmC1, C2
220kPotentiometers:Potentiometer_Trimmer_Bourns_3269WRV1, RV2
2232kResistors_SMD:R_0603R3, R4
23.3kResistors_SMD:R_0603R5, R6
2Conn_01x03Connectors2:3-pins_150milJ1, J2
1LT3089-TSSOPHousings_SSOP:TSSOP-16-1EP_4.4x5mm_Pitch0.65mmU1
1LT3090-MSOPHousings_SSOP:MSOP-12-1EP_3x4mm_Pitch0.65mmU2

More from nacs-lab/yyc-data

4
  • 4 layers56.4 × 61 mmPreamp regulator, the printed circuit board in 3D

    Preamp regulator

    nacs-lab/yyc-data

    Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply…

    90 parts2
  • 4 layers110.2 × 72.4 mmDds power, the printed circuit board in 3D

    Dds power

    nacs-lab/yyc-data

    Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply…

    51 parts2
  • 4 layers63.5 × 45.7 mmCmr link, the printed circuit board in 3D

    Cmr link

    nacs-lab/yyc-data

    Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply…

    44 parts2
  • 4 layers56.4 × 20.3 mmPre amp, the printed circuit board in 3D

    Pre amp

    nacs-lab/yyc-data

    Both connectors (Camera link an the 2x30 connector to the breakout board) and the decoder chip are on the same (front) side of the board, which is the side that is closer to the FMC connector and the DDS power supply…

    28 parts2

Similar boards

  • 4 layers56.5 × 96.5 mmCnc controller, the printed circuit board in 3D

    Cnc controller

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    34 parts397Apache-2.0
  • 4 layersMc33926 breakout, the printed circuit board in 3D

    Mc33926 breakout

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    34 parts282
  • 4 layers39 × 32 mmAmplifier, the printed circuit board in 3D

    Amplifier

    azonenberg/starshipraider

    Open hardware test equipment

    34 parts193BSD-3-Clause
  • 4 layers12.7 × 11.6 mmModule, the printed circuit board in 3D

    Module

    Szybet/Yatchy

    A modular, hackable, improved watchy like watch

    34 parts184
  • 4 layers167.7 × 68.9 mmPCIexpress x8 low, the printed circuit board in 3D

    PCIexpress x8 low

    lucanastasio/PCIexpress-KiCad

    PCI express libraries and templates for KiCad

    34 parts170
  • 4 layers89 × 93 mmTest squid, the printed circuit board in 3D

    Test squid

    clydeshaffer/gametank

    design files for the gametank hardware implementation

    34 parts150
  • 4 layers42 × 49.6 mmProcyon 42x50, the printed circuit board in 3D

    Procyon 42x50

    george-norton/procyon

    A small I2C trackpad

    34 parts100CERN-OHL-S-2.0
  • 4 layers55 × 66 mmBela Gem Multi, the printed circuit board in 3D

    Bela Gem Multi

    BelaPlatform/bela-hardware

    Bela cape and capelets

    34 parts42

Questions

How big is the Regulator PCB?

It measures 56.4 × 20.3 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Regulator use?

34 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Regulator KiCad files?

From the nacs-lab/yyc-data repository on GitHub, at the commit this page was made from: the board is designs/regulator/regulator.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Regulator design in my own project?

Its repository states no licence, so its author keeps all rights: ask nacs-lab before reusing the design.