Skip to the content
4 layers25.2 × 27.3 mmCrazyflie ESP32-Deck, the printed circuit board in 3D

Crazyflie ESP32-Deck

mrxllone/Crazyflie-ESP32-Deck1

The ESP32-C6's purpose is mainly to enable relative positioning with WiFi-FTM, which is part of my master's thesis.

Size
25.2 × 27.3 mm
Copper layers
4
Thickness
1.6 mm
Parts
38
Nets
56
Pads
193
Tracks, vias
321, 41
Pours
3
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
6 Feb 2026
Updated
21 May 2026

Overview

Crazyflie ESP32-Deck is an open-source printed circuit board by mrxllone, from the mrxllone/Crazyflie-ESP32-Deck repository on GitHub. It is a 4-layer board of 25.2 × 27.3 mm with 38 parts on 56 nets, routed with 321 tracks and 41 vias.

It is built around the ESP32-C6-MINI-1U-H4, DS28E05P+ and TC2117-3.0VDBTR, with the USB6B1 among its other parts. Its parts include 13 resistors, 8 capacitors, 4 ICs, 4 connectors and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.

Main components

4

README

README.md

Crazyflie_ESP32_Deck

A deck PCB to mount an ESP32-C6 onto the CrazyFlie 2.1.

The ESP32-C6's purpose is mainly to enable relative positioning with WiFi-FTM, which is part of my master's thesis.

Quick documentation

(will be revised later)

Power Supply

  • The ESP32-Deck can be either connected to the regulated 3.0V supply of the Crazyflie's mainboard, or use its own LDO voltage regulator powered directly from the VCOM power supply of the Crazyflie system. The latter method is recommended, since the ESP32 can easily overload the supply capabilities of the Crazyflie's voltage regulator, worst-case resulting in a total crash.
  • When using the the Deck's own LDO voltage regulator, either a 3.0V or a 3.3V can be installed. 3.3V is better for efficiency and is exactly the spec recommended by the ESP32's datasheet. To make sure the ESP32-Deck does not damage other decks which are a 3.0V-system, it can be powered by 3.0V itself, which is still allowable for the ESP32-C6, but on the lower end of the specifiaction. Refer to the "Configurable Resistors" section for furher information.
  • When the ESP32-Deck is not connected to the Crazyflie itself, it can be powered via USB to flash it or test it. Refer to "Jumpers"/JP3 for further information.

Buttons

  • SW1 "BOOT": Pulls GPIO9 of the ESP32-C6 low, thus putting it into "download mode" after a reset
  • SW2 "RESET": Pulls EN/CHIP_PU of the ESP32-C6 low, disabling it / forcing it into reset state

To be able to flash the firmware to the ESP, hold the "BOOT" button, while pressing the "RESET" button shortly. After this, the ESP will be in download mode and its firmware can be flashed via USB/JTAG or the UART header (J3).

Jumpers

  • JP1 "3V0_VCC": When closed, the 3.0V supply from the Crazyflie's mainboard will be connected to the VCC (power supply) net on the ESP32-Deck. WARNING: only do this, if U2 (the board's own LDO voltage regulator) is NOT INSTALLED. Otherwise, the Crazyflie's mainboard will likely be damaged.
  • JP2 "EN_to_IO": When closed, the Crazyflie's mainboard is able to control the ESP's EN/CHIP_PU via its IO1, This enables the mainboard to control / reset the ESP32-C6 if required.
  • JP3 "USB_VCOM": This jumper should be normally open. It is only required to close it, when the ESP32-Deck is detached from the Crazyflie's mainboard and should be supplied via USB for flashing or testing. Closing this jumper connects the USB-C's VBUS (+5V) to the VCOM of the Deck, enabling it to be supplied over USB. Do not leave this jumper closed, when the board is attached to the Crazyflie's mainboard. This could result in severe damage, because VCOM is only supposed to be powered by the Crazyflie's own energy management chip.

Configurable Resistors

  • R12 / R13: This voltage divider is used for the UART TX signal transmitted by the ESP32-C6. It is required if the ESP is running at 3.3V but other decks are only compatible with a lower voltage (like the Lighthouse deck - according to its datasheet, maximum 3.0V is allowed). When VCC on the ESP32-Deck is 3.0V, R13 is not populated and R12 is 0R (shorted) or 10R (for signal damping).
  • R14 / R15: Same principle as R12 / R13, but for the SPI MISO signal.

Parts

38
QtyValueFootprintReferences
310kmva-one-lib:R_0805R3, R6, R7
210mva-one-lib:R_0805R12, R14
2100nmva-one-lib:C_0805C1, C5
210umva-one-lib:C_0805C4, C6
21umva-one-lib:C_0805C2, C3
227mva-one-lib:R_0805R8, R9
247pmva-one-lib:C_0805C7, C8
25k1mva-one-lib:R_0805R10, R11
2VAL**bitcraze:EXP_ORIENTATIONEXP_ORIENTATION, EXP_ORIENTATION
2~mva-one-lib:R_0805R13, R15
1100kmva-one-lib:R_0805R2
11N5819HW1-7-Fmva-one-lib:D_SOD-123FD1
11k@100MHzmva-one-lib:R_0805FB1
1200kmva-one-lib:R_0805R1
13V0_VCCmva-one-lib:JP_SolderJumper_2JP1
1BOOTButton_Switch_SMD:SW_SPST_B3U-1000PSW2
1CF_EXP_LEFTCrazyflie_ESP32_Deck_FP:CF2-DECK-SMD-HOLESJ1
1CF_EXP_RIGHTCrazyflie_ESP32_Deck_FP:CF2-DECK-SMD-HOLESJ2
1DS28E05Package_TO_SOT_SMD:SOT-23U1
1EN_to_IOmva-one-lib:JP_SolderJumper_2JP2
1ESP32-C6-MINI-1/Umva-one-lib:MCU_ESP32-C6-MINI-1U3
1ESP_UARTmva-one-lib:PinHeader_1x03_P2.54mmJ3
1RESETButton_Switch_SMD:SW_SPST_B3U-1000PSW1
1TC2117-3.0VDBTRPackage_TO_SOT_SMD:SOT-223-3_TabPin2U2
1USB6B1mva-one-lib:SOIC-8_3.9x4.9mmU4
1USB_C_Receptacle_USB2.0mva-one-lib:USB-C-Receptacle_GCT_USB4105J4
1USB_VCOMConnector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_VerticalJP3

Similar boards

  • 2 layers25.2 × 27.3 mmCf2-hcsr04, the printed circuit board in 3D

    Cf2-hcsr04

    dbrgn/crazyflie2-hcsr04

    Ultrasonic sensor (HC-SR04) extension board for the Crazyflie 2.0

    9 parts2
  • 4 layers36 × 36 mmCF2X V2 OLD, the printed circuit board in 3D

    CF2X V2 OLD

    ObitoLambo/CF2X

    115 parts
  • 4 layers40.9 × 34.1 mmCustomBoard, the printed circuit board in 3D

    CustomBoard

    CloudyPadmal/CrazyFlieToFDeck

    This repository contains KiCAD source files and generated gerber files for CrazyFlie Obstacle Avoidance Sensor Deck.

    36 parts4
  • 4 layers99.6 × 76.2 mmE TKT, the printed circuit board in 3D

    E TKT

    andreisperid/E-TKT

    open source embossed label maker

    110 parts481MIT
  • 4 layers328.6 × 38.1 mmFnrow, the printed circuit board in 3D

    Fnrow

    dinofizz/fnrow-pcb

    KiCad files for the FnRow mechanical keyboard

    54 parts13
  • 2 layers109 × 95 mmStm32, the printed circuit board in 3D

    Stm32

    eddyem/tsys01

    BTA primary mirror thermal monitoring using STM32 and TSYS01

    93 parts4GPL-3.0
  • 2 layers100 × 68.5 mmKeyboard, the printed circuit board in 3D

    Keyboard

    maxryan4/Keyboard

    Custom Keyboard using STM32

    43 parts3

Questions

How big is the Crazyflie ESP32-Deck PCB?

It measures 25.2 × 27.3 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Crazyflie ESP32-Deck use?

38 parts, built around the ESP32-C6-MINI-1U-H4, DS28E05P+, TC2117-3.0VDBTR and USB6B1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Crazyflie ESP32-Deck KiCad files?

From the mrxllone/Crazyflie-ESP32-Deck repository on GitHub, at the commit this page was made from: the board is Hardware/Crazyflie_ESP32_Deck.kicad_pcb and its schematic Hardware/Crazyflie_ESP32_Deck.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Crazyflie ESP32-Deck design in my own project?

Its repository states no licence, so its author keeps all rights: ask mrxllone before reusing the design.