4 layers37.1 × 37.2 mm
Doorman
AzonInc/Doorman
ESP32-S3 based Intercom Gateway (TCS / Koch / Niko / Scantron / Analogue Systems)
44 parts252GPL-3.0
2 layers37 × 37 mm
ZigbeeLEDController
ModestoHagney/zigbee-led-stripZigbee colour light firmware for a WS2812 strip on ESP32-H2 / ESP32-C6
- Size
- 37 × 37 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 48
- Pads
- 159
- Tracks, vias
- 159, 61
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 4 Oct 2026
- Updated
- 12 Oct 2026
Overview
ZigbeeLEDController is an open-source printed circuit board by ModestoHagney, from the ModestoHagney/zigbee-led-strip repository on GitHub. It is a 2-layer board of 37 × 37 mm with 33 parts on 48 nets, routed with 159 tracks and 61 vias.
It is built around the ESP32-C6-MINI-1U-H4, AP63203WU and GT-USB-7010ASV, with the SMBJ24A, HX-B3U-1000P-1.6N and CC0805KRX7R9BB104 among its other parts. Its parts include 11 resistors, 9 capacitors, 4 ICs, 3 diodes and 2 connectors. It belongs with the radio and wireless and lEDs and displays boards and the ESP32 and RISC-V boards of this library.
Main components
9
ESP32-C6-MINI-1U-H4
SMD,13.2x12.5mm-105.5dBm -40℃~+105℃ 2.4GHz 20.5dBm 382mA 3V~3.6V 73mA ESP32-C6FH4 Integrated Bluetooth function、Integrated Zigbee function、Support USB interface UART、SDIO、SPI、I2C、GPIO、USB SMD,13.2x12.5mm WiFi Modules ROHSEspressif SystemsWiFi Modules
AP63203WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.3V 3.8V~32V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters
GT-USB-7010ASV
SMD-40℃~+85℃ 1 1.68mm 10,000 Cycles 16P 24V 3A 7.35mm Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSG-SwitchUSB Connectors
SMBJ24A
DO-214AA(SMB)-55℃~+150℃ 15.4A 24V 26.7V 38.9V 5uA 600W TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHSGOODWORKESD And Surge Protection (TVS/ESD)
HX-B3U-1000P-1.6N
SMDUncategorisedhanxia
CC0805KRX7R9BB104
0805100nF 50V X7R ±10% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMTCH221K
SOT-23-6-40℃~+105℃ 100W 5V、9V、12V、15V、20V PD 3.0 Power Receiver Controller SOT-23-6 USB PD ROHSWCH (Nanjing Qinheng Microelectronics)USB PD
SMMS0420-4R7M
SMD,4.6x4.2mm126mΩ 2.5A 3A 4.7uH Molded Inductor ±20% SMD,4.6x4.2mm Molding Power Inductors ROHSSXNPower InductorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
README
README.md| Supported Targets | ESP32-C6 | ESP32-H2 |
|---|
Zigbee LED Strip
Firmware that turns an ESP32-H2 or ESP32-C6 and a WS2812 strip into a Zigbee colour light. It joins the network as an end device and shows up in Home Assistant as one colour dimmable light (on/off, brightness, and colour in either hue/saturation or XY).
The whole strip is one light: every pixel gets the same colour.
Boards
One source builds for both chips. main/config.h picks the settings
from the chip target:
| Target | LED data pin | LED count | Zigbee model |
|---|---|---|---|
| ESP32-H2 | GPIO 22 | 64 | H2-LED |
| ESP32-C6 | GPIO 19 | 144 | C6-LED |
Manufacturer name is NiftyFish. Colour order (GRB), power source and
the Zigbee endpoint are also set in main/config.h.
Hardware
hardware/ZigbeeLEDController/ is the KiCad 9 project for the
controller board: an ESP32-C6-MINI-1 with a USB-C input, a CH221K USB
PD sink, an AP63203 3.3 V buck regulator and an LED strip output. The
folder also has the PCBWay fabrication zip (.kicad_pcb.zip: gerbers,
BOM and positions) and a STEP export of the board.
Build and flash
Needs ESP-IDF 5.x (built with v5.5.2).
idf.py set-target esp32h2
idf.py -p PORT flash monitorUse esp32c6 for the C6 board. Switching target regenerates
sdkconfig and dependencies.lock; neither is committed.
Run idf.py -p PORT erase-flash first if the board has been paired
before and you want it to join as a new device.
Pairing
On first boot (or after an erase) the device starts network steering
on its own. Put the coordinator into permit-join and it should log
joined network! ready.
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1K | Resistor_SMD:R_0805_2012Metric | R6, R12, R14 |
| 3 | 22uF | Capacitor_SMD:C_0805_2012Metric | C2, C12, C13 |
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C3, C4 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric | R7, R15 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C1, C5 |
| 2 | 22 | Resistor_SMD:R_0805_2012Metric | R8, R9 |
| 2 | 5.1K | Resistor_SMD:R_0805_2012Metric | R10, R11 |
| 2 | HX-B3U-1000P-1.6N | EasyEDA:SW-SMD_2P-L3.0-W2.5-LS4.0 | SW1, SW2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D1, D2 |
| 1 | 100nf | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | AP63203WU | Package_TO_SOT_SMD:TSOT-23-6 | U3 |
| 1 | CH221K | EasyEDA:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BL-2 | Q1 |
| 1 | Conn_01x03_Pin | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x07 | custom_footprints:1x07_SOLDER_PAD_1.7x4_LABEL | J1 |
| 1 | ESP32-C6-MINI-1/U | PCM_Espressif:ESP32-C6-MINI-1 | U1 |
| 1 | GT-USB-7010ASV | EasyEDA:USB-C-SMD_G-SWITCH_GT-USB-7010ASV | U4 |
| 1 | R | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | SMBJ24A | EasyEDA:SMB_L4.3-W3.6-LS5.3-RD | U2 |
| 1 | SMMS0420-4R7M | EasyEDA:IND-SMD_L4.8-W4.5 | L2 |
| 1 | USBLC6-2SC6 | EasyEDA:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BL | D3 |
Questions
How big is the ZigbeeLEDController PCB?
It measures 37 × 37 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ZigbeeLEDController use?
33 parts, built around the ESP32-C6-MINI-1U-H4, AP63203WU, GT-USB-7010ASV and SMBJ24A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ZigbeeLEDController KiCad files?
From the ModestoHagney/zigbee-led-strip repository on GitHub, at the commit this page was made from: the board is hardware/ZigbeeLEDController/ZigbeeLEDController.kicad_pcb and its schematic hardware/ZigbeeLEDController/ZigbeeLEDController.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ZigbeeLEDController design in my own project?
Its repository states no licence, so its author keeps all rights: ask ModestoHagney before reusing the design.
Similar boards
- 2 layers47.7 × 51.2 mm
CO2Monitor
AntoG00/ESP32-C6-CO2-Monitor
Low-power CO2, temperature and humidity monitor using ESP32-C6 and E-Paper display.
54 partsMIT - 4 layers100 × 100 mm
- 4 layers250.8 × 30 mm
- 2 layers65.5 × 30 mm
- 4 layers50 × 23 mm
- 6 layers47 × 69.4 mm
- 4 layers92 × 56 mm
REIN R1
rein-baremetal/REIN_R1_KiCad
Dual-MCU baremetal embedded development board featuring high-speed QSPI storage, hardware USB hub, and flexible power management. Open for PCB trace routing collaboration
177 parts2