
Nixie board
vascofazza/cloxie_nixie_clock
Schematics and code for Cloxie: my Nixie Tube Clock.

MQTemp is an open-source printed circuit board by mmaschenk, from the mmaschenk/mqtemp-pcb repository on GitHub, published under the MIT licence. It is a 2-layer board of 48.3 × 45.7 mm with 10 parts on 16 nets, routed with 50 tracks and 0 vias.
It is built around the WEMOS D1 MINI and DS18B20. Its parts include 4 resistors, 1 connector and 1 switch. It belongs with the ESP8266 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100k | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1, R2 |
| 1 | 18k | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R4 |
| 1 | 4k7 | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R3 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | DS18B20 | Package_TO_SOT_THT:TO-92_Inline | DS18B20 |
| 1 | LOGO | logos:mark-20mm | G*** |
| 1 | LOGO | logos:tudelft-10mm | G*** |
| 1 | SW_DIP_x01 | Button_Switch_THT:SW_DIP_SPSTx01_Slide_9.78x4.72mm_W7.62mm_P2.54mm | SW1 |
| 1 | WeMos_D1_mini | Module:WEMOS_D1_mini_light | WEMOSD1mini1 |

vascofazza/cloxie_nixie_clock
Schematics and code for Cloxie: my Nixie Tube Clock.

andreq/iSpindel-Gravitymon-Pill-PCB
A PCB used to build an iSpindel or GravityMon hydrometer that fit into a *popular brand* Pill casing instead of a PETling container

AK-Homberger/BD35F-FridgeController
An electronic thermostat for a Danfoss/Secop BD35F Compressor with ESP8266.

strayer/EnvironmentalSensor
A WiFi environmental sensor based on Tasmota that reports temperature, air pressure, air quality, humidity and CO2 (ppm).


mitchins/ESP-Aquarium-Water-Sensor
A simple water flow and quality sensor for aquariums based on ESP controller

makerspacelt/wiscale-mod-hw
This is ESP8266 and HX711 based weight monitoring device.

SparkMakerspace/summer_melt_badge_2022
This badge was designed for the 2022 Summer Melt at Spark Makerspace.
It measures 48.3 × 45.7 mm and has 2 copper layers, 1.6 mm thick.
10 parts, built around the WEMOS D1 MINI and DS18B20. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mmaschenk/mqtemp-pcb repository on GitHub, at the commit this page was made from: the board is MQTemp.kicad_pcb and its schematic MQTemp.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).