2 layers38 × 200 mm
SPACEDOS02A PCB01A
UniversalScientificTechnologies/SPACEDOS02
Solid-state PIN diode dosimeter for manned spacecraft. Liulin detector replacement.
120 parts8GPL-3.0
2 layers80.8 × 101.1 mm
DATALOGGER01
mlab-modules/DATALOGGER011Universal Arduino based data logger to SDcard.
- Size
- 80.8 × 101.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 90
- Nets
- 53
- Pads
- 301
- Tracks, vias
- 758, 220
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 28 Oct 2020
- Updated
- 17 Sep 2023
Overview
DATALOGGER01 is an open-source printed circuit board by mlab-modules, from the mlab-modules/DATALOGGER01 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 80.8 × 101.1 mm with 90 parts on 53 nets, routed with 758 tracks and 220 vias.
It is built around the ATMEGA1284P-AU, AT24CS64-SSHM-B and ISL21080CIH320Z-TK, with the PCF85263AT/AJ, BX0037 and 5MS1S102AM6QES among its other parts. Its parts include 34 connectors, 22 capacitors, 14 resistors, 6 ICs and 2 diodes. It belongs with the sensors and measurement and power boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
7
ATMEGA1284P-AU
TQFP-44(10x10)-40℃~+85℃ 1.8V~5.5V 10bit 128KB 16KB 20MHz 32 4KB 8 Bit AVR Built-in FLASH TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
AT24CS64-SSHM-B
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 years 1MHz 3mA 5ms 64Kbit 6uA 900ns Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROM
ISL21080CIH320Z-TK
SOT-23-40℃~+85℃@(Ta) 1.5uA 2.048V 2.7V~5.5V 30uVp-p 50ppm/℃ 52uVrms 7mA Fixed Series ±0.3% SOT-23 Voltage Reference ROHSRenesas ElectronicsVoltage ReferencePCF85263AT/AJ
SO-8-40℃~+85℃ 0.28uA 280nA 900mV~5.5V Built-in I2C Watchdog timer、Backup power management and battery charging、Timestamp function、Programmable clock output、Alarm function、Periodic interrupt output Yes SO-8 Real Time Clocks ROHSNXP SemiconductorsReal Time Clocks
BX0037
-- Button And Strip Battery Connector ROHSBulginButton And Strip Battery Connector5MS1S102AM6QES
插件插件 Slide Switches ROHSDailywellSlide SwitchesABS07-120-32.768KHZ-T
SMD3215-2P-40℃~+85℃ 32.768kHz 55kΩ 6pF ±20ppm SMD3215-2P Crystals ROHSAbraconCrystals
README
README.mdDATALOGGER01 - MLAB's Versatile processor module
The DATALOGGER01 is a versatile electronic module designed by MLAB, containing an ATmega1284p processor. The module is programmable in the Arduino IDE and compatible with a variety of development environments and programming languages.
One of the significant features of this module is an SD card slot, a convenient provision for data logging from the processor. With a built-in battery holder, the module ensures uninterrupted operation without reliance on an external power supply.
The DATALOGGER01 exhibits a range of applications, thanks to its I2C, UART, ADC input, and GPIO pins. Additionally, it's furnished with a power switch to effectively manage power consumption of connected devices.
Setting it apart, the module includes an EEPROM AT23CS64, containing a unique serial number to distinguish logs from different DATALOGGER01-based devices. Moreover, it comprises a PCF85263 RTC circuit, with the option to connect a backup battery.
Key Features:
- Processor: ATmega1284p
- Interoperability: Compatibility with Arduino and supports a range of other development platforms and programming languages.
- Data Logging: An SD Card Slot for extensive data storage.
- Power Management: Self-sufficient with an integrated battery holder.
- Connectivity Options: Diverse interfacing options with I2C, UART, ADC input, and GPIO pins.
- Energy Efficiency: Onboard power switch for managing external devices' power consumption.
- Unique Identification: Inbuilt EEPROM AT23CS64 with a unique serial number.
- Real-Time Tracking: Inclusion of a PCF85263 RTC circuit with backup battery connectivity.
Potential Use Cases:
- Data Collection: Can collect, store, and analyze data from various sensors and devices.
- Remote Monitoring: Can be incorporated into IoT systems for remote data collection and monitoring.
- Autonomous Systems: Suitable for devices needing independent functioning.
- Space Research: Applicable as data loggers and locator devices for stratospheric balloons.
In Action:
- The DATALOGGER01 module has proven its efficacy in:
Schematics
Useful Links:
- ATmega1284p - Wikipedia
- ARDUINO Programming Environment - Official Arduino Site
- EEPROM AT23CS64 - Mouser Electronics
- PCF85263 - NXP Semiconductors
Discover the potential of DATALOGGER01 module and utilize it for your projects!
Parts
90| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | HEADER_2x01_PARALLEL | Mlab_Pin_Headers:Straight_2x01 | J1, J2, J12, J13, J14, J15, J16, J17, J18, J19, J20, J22, J23, J24, J25, J26 +8 |
| 15 | 100nF | Mlab_R:SMD-0805 | C1, C2, C3, C4, C5, C6, C8, C13, C15, C17, C18, C19, C20, C21, C22 |
| 4 | 100 | Mlab_R:SMD-0805 | R1, R2, R3, R4 |
| 4 | HEADER_2x01 | Mlab_Pin_Headers:Straight_2x01 | J9, J11, J21, J32 |
| 3 | - | Mlab_R:SMD-0805 | R8, R11, R16 |
| 3 | 10k | Mlab_R:SMD-0805 | R6, R7, R9 |
| 3 | HEADER_2x03_PARALLEL | Mlab_Pin_Headers:Straight_2x03 | J6, J10, J33 |
| 3 | HOLE | Mlab_Mechanical:MountingHole_3mm | M2, M3, M4 |
| 2 | 0R | Mlab_R:SMD-0805 | R12, R15 |
| 2 | 10uF | Mlab_R:SMD-0805 | C11, C14 |
| 2 | 750mA | Mlab_F:1812 | F1, F2 |
| 2 | BX0037 | Mlab_Batery:BX0037 | BT1, BT2 |
| 1 | 10uH - LQH32CN100K23L | Mlab_R:SMD-1210 | L1 |
| 1 | 16MHz | Mlab_XTAL:Crystal_HC49-U_Vertical | Y1 |
| 1 | 1nF | Mlab_R:SMD-0805 | C12 |
| 1 | 1uF | Mlab_R:SMD-0805 | C7 |
| 1 | 2k2 | Mlab_R:SMD-0805 | R10 |
| 1 | 47uF | Mlab_C:TantalC_SizeC_Reflow | C9 |
| 1 | 4k7 | Mlab_R:SMD-0805 | R5 |
| 1 | 4u7 | Mlab_R:SMD-0805 | C16 |
| 1 | 5MS1S102AM6QE | Mlab_SW:5MS1S102AM6QE | SW1 |
| 1 | ABS07-120-32.768KHZ-T | Mlab_XTAL:ABS07 | Y2 |
| 1 | AT24CS64-SSHM | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | ATMEGA1284P-AU | Package_QFP:TQFP-44_10x10mm_P0.8mm | U3 |
| 1 | Battery_Cell-device | Mlab_Batery:CH28-2032 | BT3 |
| 1 | EMI_Filter_C | Mlab_L:FIR1 | C10 |
| 1 | HEADER_2x03 | Mlab_Pin_Headers:Straight_2x03 | J31 |
| 1 | HLMP-K150+FIX-LED-313 | Mlab_D:FIX-LED-313 | D3 |
| 1 | ISL21080CIH320Z-TK | Package_TO_SOT_SMD:SOT-23 | U1 |
| 1 | LM4041CIM3-1.2(neosazovat) | Package_TO_SOT_SMD:SOT-23 | U5 |
| 1 | M4 | Mlab_D:SMA_Standard | D2 |
| 1 | MCC-SD | Connector_Card:SD_TE_2041021 | J7 |
| 1 | MCC-SD (kouka z modulu) | Mlab_CON:MCC-SD | J34 |
| 1 | PCF85263A | Mlab_IO:TSSOP-10_3x3mm_Pitch0.5mm | U4 |
| 1 | TPS22965-Q1 | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm_ThermalVias | U2 |
Questions
How big is the DATALOGGER01 PCB?
It measures 80.8 × 101.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DATALOGGER01 use?
90 parts, built around the ATMEGA1284P-AU, AT24CS64-SSHM-B, ISL21080CIH320Z-TK and PCF85263AT/AJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DATALOGGER01 KiCad files?
From the mlab-modules/DATALOGGER01 repository on GitHub, at the commit this page was made from: the board is hw/sch_pcb/DATALOGGER01.kicad_pcb and its schematic hw/sch_pcb/DATALOGGER01.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DATALOGGER01 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers136.2 × 85.9 mm
BATDATUNIT01
mlab-modules/BATDATUNIT01
Multiple parallel Li-ion 18650 battery cell module with BMS and data storage with MCU control.
225 parts5GPL-3.0 - 4 layers90.9 × 50.3 mm
- 2 layers93.5 × 48.2 mm
SPACEDOS01
UniversalScientificTechnologies/SPACEDOS01
Silicon diode dosimeter optimized for spacecraft dosimetry
92 parts5GPL-3.0 - 2 layers101.1 × 60.5 mm
DATALOGGER02
mlab-modules/DATALOGGER02
Arduino based data logger with LoRa IoT interface.
161 partsGPL-3.0 - 4 layers
Power board v1
N-Pulse/EEG-HW-System
EEG acquisition board, power board and headset development
79 parts - 4 layers60 × 34.1 mm
Power v3.3
N-Pulse/BMI-EMG-HW
Find the schematics and PCB layout for the hardware of the EMG Bracelet
63 parts - 4 layers80 × 80 mm
