
Hour meter board microfit can handroute
ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator

PCB for AM4096 encoder with STM32F103RBT6 microcontroller and terminals for DC motor controller based on two L6390D with CAN bus interface.
Electric angle actuator is an open-source printed circuit board by MichalKacperek, from the MichalKacperek/electric_angle_actuator repository on GitHub. It is a 4-layer board of 73.2 × 41.9 mm with 66 parts on 78 nets, routed with 771 tracks and 139 vias.
It is built around the TJA1051T/3/1J, LM2596S-5.0 and AMS1117-3.3, with the USBLC6-2SC6 and SS54 among its other parts. Its parts include 30 capacitors, 10 resistors, 6 ICs, 5 connectors and 4 diodes. It belongs with the robots and motor control and interfaces and adapters boards and the STM32 boards of this library.
PCB for AM4096 encoder with STM32F103RBT6 microcontroller and terminals for DC motor controller based on two L6390D
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C3, C7, C8, C12, C14, C18, C20, C22, C24, C25, C26, C27 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 10n | Capacitor_SMD:C_0402_1005Metric | C6, C9, C29 |
| 3 | 10u | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I | C10, C15, C19 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R8, R9, R10 |
| 3 | 47k | Resistor_SMD:R_0402_1005Metric | R2, R4, R5 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D2, D3, D4 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R3, R7 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C21, C23 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C5, C11 |
| 2 | 220u | Capacitor_SMD:CP_Elec_10x10.5 | C4, C13 |
| 2 | 22u | Capacitor_SMD:C_1206_3216Metric | C16, C17 |
| 1 | 120R | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1k5 | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C28 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C30 |
| 1 | 39n | Inductor_SMD:L_0402_1005Metric | FB1 |
| 1 | 470n | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 47uH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | AM4096 | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | Conn_01x06 | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J3 |
| 1 | Conn_02x13_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_Vertical | J2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U2 |
| 1 | SS54 | Diode_SMD:D_SMA | D1 |
| 1 | STM32F103RBTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U6 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J5 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3-5.08_1x03_P5.08mm_Horizontal | J4 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | TJA1051T/3/1J | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J1 |
The 63 most common of 66 parts.

ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator

ChladpavPy/Super3DMaker
So first I want to explain, why I started this project. I had an old Profi3DMaker 3D printer at home, which was not used for a long time, mainly because of the hardware, which was just outdated.

renatorgr/Boards
Hardware and firmware for the AgOpenGPS AiO v4.5 autosteer boards: Teensy 4.1 firmware with its own web page (GPS, IMU, autosteer), a XIAO ESP32 Wi-Fi status page, XIAO adapter boards, and an Arduino Nano sprayer…


jad-jkh/Smart-Table-Solutions
Sample files from Jad Haddad's Smart Table Solutions including: KiCad PCB files (schematic, layout, and 3D view) and screenshots, along with embedded C code for motor control

rmalchow/ondaire
A KiCad 10 project for a powered-speaker node: an ESP32-S3 dev board drops into a socket, an I²S DAC + class-D amp turn the stream into 40–50 W of audio, and the whole thing runs from a single USB-C cable via USB-PD.


justinlindh/digits
Encrypted retro phone network — private VoIP over vintage desk phones
It measures 73.2 × 41.9 mm and has 4 copper layers, 1.6 mm thick.
66 parts, built around the TJA1051T/3/1J, LM2596S-5.0, AMS1117-3.3 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the MichalKacperek/electric_angle_actuator repository on GitHub, at the commit this page was made from: the board is electric_angle_actuator.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask MichalKacperek before reusing the design.