4 layers184.3 × 131 mm
2 layers34 × 48 mm
Ripple
MatrixSenpai/rippleA small temperature box featuring a small led display and neopixel ring.
- Size
- 34 × 48 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 67
- Pads
- 220
- Tracks, vias
- 437, 49
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 17 May 2025
- Updated
- 21 Nov 2025
Overview
Ripple is an open-source printed circuit board by MatrixSenpai, from the MatrixSenpai/ripple repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 34 × 48 mm with 56 parts on 67 nets, routed with 437 tracks and 49 vias.
It is built around the RP2040, BME680 and W25Q128JVSIQ. Its parts include 19 capacitors, 16 resistors, 5 ICs, 5 diodes and 5 connectors. It belongs with the RP2040 boards of this library.
Main components
3
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
BME680
LGA-8-40℃~+85℃ 0.12hpa 0.6hpa 1.3pa/K 1.71V~3.6V 150nA 30Kpa~1.1bar I2C、SPI Temperature Sensor LGA-8 Pressure Sensors ROHSBosch SensortecPressure Sensors
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
README
README.mdRipple
A small temperature box featuring a small led display and neopixel ring.
SW licensed under MIT license. HW licensed under CC BY-SA.
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C6, C7, C8, C9, C10, C12, C13, C14, C18, C19 |
| 5 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R9, R10, R11, R12 |
| 3 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C17 |
| 3 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6, R7 |
| 2 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R15 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R17 |
| 2 | 15p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15, C16 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R16 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C11 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3 |
| 1 | 3V | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | 5V | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | BME680 | Package_LGA:Bosch_LGA-8_3x3mm_P0.8mm_ClockwisePinNumbering | U5 |
| 1 | BOOTSEL | parts:SW_SKRPACE010 | S1 |
| 1 | CHRG | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | D_Schottky_Small | Diode_SMD:D_SOD-323_HandSoldering | D1 |
| 1 | HDR_BATT | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | HDR_DBG | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J4 |
| 1 | HDR_DSP | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J5 |
| 1 | HDR_LED | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | LOGO | parts:gh_qrcode | G*** |
| 1 | MCP73831-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | PMOS | Package_TO_SOT_SMD:SOT-23-3 | Q1 |
| 1 | RESET | parts:SW_SKRPACE010 | S2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | STAT | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | SW_SPDT_321 | parts:SW3_JSX08001SAQNL_CNK | SW1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |
Questions
How big is the Ripple PCB?
It measures 34 × 48 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ripple use?
56 parts, built around the RP2040, BME680 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ripple KiCad files?
From the MatrixSenpai/ripple repository on GitHub, at the commit this page was made from: the board is pcb/ripple.kicad_pcb and its schematic pcb/ripple.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ripple design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 6 layers53.3 × 101.6 mm
Mega2560plus
sneakylizard123-4/Mega2560plus
Mega 2560+ is an upgraded version of the Arduino Mega 2560. It keeps the same form factor and pinout as the original so it still works with every Mega shield, but it adds an onboard sensor suite and an ESP32-S3…
149 parts - 4 layers149.6 × 98 mm
- 2 layers42 × 67 mm
- 2 layers181 × 97 mm
OpenDeck r3.1.2
shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.
262 parts960Apache-2.0 - 4 layers82.6 × 82.5 mm
- 4 layers102.9 × 96.7 mm
PicoGUS chipdown
polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support
99 parts805 - 4 layers180.8 × 300.3 mm
Dilemma
Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.
383 parts590