Skip to the content
2 layers25 × 6.5 mmConnector, the printed circuit board in 3D

A modular and repairable power bank

Size
25 × 6.5 mm
Copper layers
2
Thickness
0.8 mm
Parts
7
Nets
3
Pads
11
Tracks, vias
8, 0
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
18 Jul 2026
Updated
5 Nov 2026

Overview

Connector is an open-source printed circuit board by marksdude, from the marksdude/Pikne repository on GitHub. It is a 2-layer board of 25 × 6.5 mm with 7 parts on 3 nets, routed with 8 tracks and 0 vias.

It is built around the TPD2E2U06DCK. Its parts include 1 IC and 1 connector.

Main components

1

README

README.md

Pikne

A modular and repairable power bank

Example.jpg Picture of rev 1.0 nonworking build

Features:

  • USB PD output up to 60W
  • 0.91 inch OLED for status monitoring
  • Attachable modules
  • Repairable design
  • 80WH capacity
  • Based on the BQ25792 and TPS25751
  • One USB-C output

Modules:

  • LED controller - Allows you to control LEDs with Home Assistant.
    • Features:
      • Up to 2.5A output
      • 5V output
      • Home Assistant integration
      • Power monitoring on each output
      • 2 monochrome outputs, 1 RGB output and 1 addressable LED output
        • Note: RGB and the monochrome outputs can't be used simultaneously.
      • ESP32-C3 based

LED controller.png

  • Flashlight
    • Features:
      • 6600lm max brightness
        • Note: The LEDs probably won't be able to run at max brightness for very long.
      • PWM dimmable
      • STM32L011F3 based

Coming modules

  • LiPo charger - Allows you to charge up to 4S LiPos from your power bank

How does it work?

Core functionality comes from the TPS25751 and BQ25792 combination.

The TPS25751 is a USB-C PD controller IC. It handles PD negotiations, manages the BQ25792 and also has integrated I2C control for the BQ25792, which simplified firmware development.

The BQ25792 is a battery charger IC with support for USB-C PD output. It charges the battery and generates higher voltages (9V, 12V, 15V, 20V) for the USB C PD output. For 5V there is a separate regulator.

For example, if you connect a device you want to charge, first your device negotiates its required voltage and current with the TPS25751. Then the TPS25751 asks the BQ25792 to generate the requested voltage if it is above 5V. Once the correct voltage is available, the TPS25751 enables the output and your device starts charging.

An ATmega328P acts as the main controller. It monitors everything, handles faults, displays battery information and communicates with the modules.

The BMS is based on the BQ41Z50, a 2-4S battery manager IC. It has all the necessary protections needed for a lithium-ion battery pack and monitors its SoC (State of Charge). The ATmega328P requests battery information from the BMS over SMBus.

Modules can communicate with the power bank over UART through the pogo pins above the USB-C port. A connected module is idendified with an ID number sent by the module (1 for LED controller, 2 for Flashlight). The module can then request battery information or use the button on the power bank for additional control.

LED controller

The LED controller is based on an ESP32-C3-WROOM-02U that is running ESPHome. There are 3 external MOSFETs that are used for the two monochrome outputs and one RGB output. An RGB output needs three MOSFETs, one for each color channel. Since there are only three, the monochrome outputs have to be connected together with two of the RGB channels. This is why the monochrome and RGB outputs can't be used simultaneously. INA219s are used for monitoring power draw of each output.

Wiring

All of the smaller connectors are JST-ZH, while the battery connectors are JST-VH.
The main PCB has 4 connectors. One goes to the pogo connector, two to the BMS and one is for programming.

Main PCb connectors.png

On the BMS two connectors go to the main PCB and two to the battery pack.

BMS connectors.png

The battery is connected in a 2S2P configuration. There are cutouts in the bottom of the battery holder for routing the wires and for the thermistors. BAT+ and BAT- connect to the BMS input, thermistors and the balance lead connect to the BMS battery sense connector.

The button has to be soldered to the main PCB. The pogo connector is connected to the main PCB.

LED controller

Not much wiring to do here just connect the pogo connector to the PCB.

Output pinout:

LED controller pinout.png

Firmware

Firmware is currently very limited. Version 0.1 has a basic menu to check some battery information, that's about it. It relies on the ArduinoSMBus library for communicating with the BMS and the Adafruit_SSD1306 and Adafruit GFX Library libraries for drawing on the OLED. I plan to move away from these libraries in the future.

There is still a lot left to be implemented.

Why did I make this?

It all started because I was tired of changing the AA batteries in my mom's battery-powered lights. I wanted to make the process faster and less wasteful, so I thought it would be a good idea to design an easily removable, rechargeable battery pack for the lights and also integrate them with Home Assistant. The original idea was going to have 2 parts the battery pack and a controller board. They were supposed to be held together with magnets, connected with pogo pins and communicate over UART. Then I thought, why not turn the battery pack into a power bank so it could be used for things other than the lights? That's what I did. The idea of making the battery pack easily removable led me to make the power bank modular. That's how Pikne was born.

Parts

7
QtyValueFootprintReferences
3TestPointTestPoint:TestPoint_Pad_D1.0mmTP1, TP2, TP3
1Conn_01x03_PinPogo_Connector:Pogo 3 PinJ1
1TPD2E2U06DCKPackage_TO_SOT_SMD:SOT-323_SC-70U1

The 5 most common of 7 parts.

More from marksdude/Pikne

7
  • 2 layers72 × 26.7 mmLiPo charger Rev 1.0, the printed circuit board in 3D

    LiPo charger Rev 1.0

    marksdude/Pikne

    A modular and repairable power bank

    117 parts1
  • 4 layers60 × 30 mmPikne Rev 1.1, the printed circuit board in 3D

    Pikne Rev 1.1

    marksdude/Pikne

    A modular and repairable power bank

    112 parts1
  • 2 layers73 × 20.8 mmLED driver Rev 1.1, the printed circuit board in 3D

    LED driver Rev 1.1

    marksdude/Pikne

    A modular and repairable power bank

    67 parts1
  • 2 layers74 × 21.5 mmLED, the printed circuit board in 3D

    LED

    marksdude/Pikne

    A modular and repairable power bank

    38 parts1
  • 4 layers50.9 × 18 mmBMS Rev 1.1, the printed circuit board in 3D

    BMS Rev 1.1

    marksdude/Pikne

    A modular and repairable power bank

    35 parts1
  • 2 layers37.5 × 10 mmConnector, the printed circuit board in 3D

    Connector

    marksdude/Pikne

    A modular and repairable power bank

    5 parts1

Similar boards

  • 4 layers100 × 75 mmOpenAirScope, the printed circuit board in 3D

    OpenAirScope

    emertcakir/OpenAirScope

    Open-source air quality and environmental monitoring node with STM32H743 + ESP32-C3, LoRaWAN, RS485, USB-C, Li-ion charging, and multi-sensor support.

    282 parts26MIT
  • 4 layers58.8 × 29 mmSparkAltBatteryBoardV1, the printed circuit board in 3D

    SparkAltBatteryBoardV1

    fahreddinaykut/SparkAltBatteryBoard

    A custom research-oriented battery interface and telemetry board for the DJI Spark platform, built around a standard 3S LiPo battery pack instead of the discontinued, hard-to-find OEM Smart Battery.

    46 parts20
  • 2 layers93.6 × 102.8 mmMote hardware, the printed circuit board in 3D

    Mote hardware

    empriselab/mote

    A low cost, high confidence mobile robot optimized for education.

    75 parts5MIT
  • 4 layers52.7 × 42.5 mmOmniProbe, the printed circuit board in 3D

    OmniProbe

    emertcakir/OmniProbe

    Open-source SWD, JTAG, UART, SPI, I2C and Logic Analyzer platform powered by RP2040

    77 parts4MIT
  • 2 layers66.6 × 41.3 mmUPIC46, the printed circuit board in 3D

    UPIC46

    emertcakir/uPIC46

    PIC18F46K22-based versatile development board with CAN, RS-485, EEPROM, RTC, and user LEDs

    111 parts2MIT
  • 4 layers100 × 100 mmBase module, the printed circuit board in 3D

    Base module

    KoNarRobotics/ModuCard-base-module

    Template for ModuCard PCBs

    163 parts2
  • 4 layers22.9 × 50.8 mmSpethernet featherwing, the printed circuit board in 3D

    Spethernet featherwing

    parzivail/adin1110-breakout

    ADIN1110 Single-pair Ethernet controller breakout with SPI

    48 parts2CERN-OHL-P-2.0
  • 2 layers125 × 78.2 mmRC ESP32 V2, the printed circuit board in 3D

    RC ESP32 V2

    Poent/RC-Snowblower

    Working on designing the impeller and auger portion of the snowblower. Switched from using a worm gear assembly to a custom ring and pinion setup using a spiral bevel gear.

    84 parts2

Questions

How big is the Connector PCB?

It measures 25 × 6.5 mm and has 2 copper layers, 0.8 mm thick.

What parts does the Connector use?

7 parts, built around the TPD2E2U06DCK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Connector KiCad files?

From the marksdude/Pikne repository on GitHub, at the commit this page was made from: the board is Modules/Flashlight/PCB/connector/connector.kicad_pcb and its schematic BMS/BMS Rev 1.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Connector design in my own project?

Its repository states no licence, so its author keeps all rights: ask marksdude before reusing the design.