Skip to the content
4 layers99.3 × 92.2 mmUWU PDB, the printed circuit board in 3D

[SUTD SOAR] 8-Thruster Central Star-Node PDB for 8× Blue Robotics T200 + Basic ESC System

Size
99.3 × 92.2 mm
Copper layers
4
Thickness
2.02 mm
Parts
67
Nets
27
Pads
188
Tracks, vias
155, 236
Pours
37
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 May 2026
Updated
19 Sep 2026

Overview

UWU PDB is an open-source printed circuit board by markantosa, from the markantosa/swimbladder repository on GitHub, published under the MIT licence. It is a 4-layer board of 99.3 × 92.2 mm with 67 parts on 27 nets, routed with 155 tracks and 236 vias.

Its parts include 19 connectors and 2 diodes. It belongs with the robots and motor control boards of this library.

README

README.md

SwimBladder

Assembled SwimBladder PDB

Power distribution board (PDB) project files for the SwimBladder project.

Silkscreen tag: SOAR UWU | 8 x T200 | V1.1

[!WARNING] This board is an unvalidated, untested work in progress (WIP). It has not completed electrical, thermal, or in-water system validation. Do not treat this design as production-ready hardware.

Project Status

  • Current state: WIP (design in progress)
  • Revision: V1.1
  • Validation status: not electrically validated
  • Test status: not thermally validated, not full-load validated, not field-tested
  • Use at your own risk until formal verification is completed

Repository Contents

  • KiCad Project Files v1.1/ - Canonical KiCad project, PCB, schematic, and the SwimBladder Custom Footprints library. Open KiCad Project Files v1.1/UWU PDB.kicad_pro.
  • KiCad Project Files/ - Deprecated earlier project set, kept for history. Do not edit.
  • SwimBladder PDB.kicad_sch (repo root) - Stale May snapshot, superseded by the schematic inside KiCad Project Files v1.1/. Do not use.
  • Screenshots/ - Board and schematic screenshots. v1.1 *.png are current; the unprefixed files are the earlier V1.0 captures.
  • SwimBladderV1.0.step - 3D board model (V1.0 geometry).
  • Swim_Bladder_Doc_v3_0.pdf - Full engineering reference and calculations. Component values in this PDF predate the V1.1 schematic changes listed below.

Project Overview

This board is designed as a compact 8-thruster central star-node PDB for Blue Robotics T200 systems with 4S battery input. It is currently in a pre-validation state and should be treated as a reference design draft.

  • System topology: battery -> cable-side main fuse -> optional e-stop/contactor -> dual XT90 input -> central high-current node -> 8 fused ESC branches -> XT60 outputs
  • Nominal battery voltage: 14.8 V (4S), full charge: 16.8 V
  • Thruster design current: about 25 A each
  • Total design current: 200 A (with burst targets up to around 280-300 A)
  • Per-branch fuse target: 30 A

Schematic Summary (V1.1)

Input / central node

  • Dual XT90 input connectors (J1, J19) feeding one common +VBAT star node, symmetrical wiring for current sharing.
  • Bulk capacitance at the node: C_MAIN1, C_MAIN2 = 4700 uF each.
  • Input TVS: D1 (D_TVS), 22-24 V standoff class for 4S. Recommended part: SMDJ22A (unidirectional, 3 kW, DO-214AB / SMC footprint, Diode_SMD:D_SMC or D_SMC_HandSolder).
  • Rail bleed / discharge: R_BLEED1 = 22 kOhm. Draws ~0.76 mA / ~13 mW continuously at full charge - trivial dissipation for a 0603, well within its power/voltage rating.
  • Power/status LED: D2 (LED) with series resistor R_LED1 = 10 kOhm.

Per-ESC branch (x8)

  • Branch fuse: F_ESC1..F_ESC8 = 30 A.
  • Branch bulk cap: C_ESC1..C_ESC8 = 1000 uF.
  • Branch high-frequency cap: C_HF1..C_HF8 = 1 uF.
  • Output: J3..J10, XT60 per branch.
  • Branch decoupling is now two caps (1000 uF + 1 uF). The earlier third per-branch cap (1 nF high-frequency) has been removed - on a high-current motor branch it contributes negligible benefit and can create anti-resonance with the larger caps.

PWM signal

  • 16-pin IDC header J2 (Conn_02x08_Odd_Even, 2x8, 2.54 mm), alternating PWM / GND pins. Suggested part footprint: Connector_IDC:IDC-Header_2x08_P2.54mm_Vertical.
  • Individual PWM channel inputs: J11..J18 (PWM1..PWM8).
  • Per-channel series resistor: R_PWM1..R_PWM8 = 100 Ohm.
  • Per-channel pulldown resistor: R_PD1..R_PD8 = 10 kOhm.

Passive Footprint Notes

  • PWM channel series resistors (R_PWM*): 0402 hand-solder land pattern (Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder) for IDC header pitch.
  • All other signal passives (R_BLEED1, R_LED1, R_PD*) and branch HF caps: 0603 hand-solder (R_0603_1608Metric_Pad0.98x0.95mm_HandSolder / C_0603_1608Metric_Pad1.08x0.95mm_HandSolder).
  • Custom / project-specific footprints live in KiCad Project Files v1.1/SwimBladder Custom Footprints.

Key Engineering Notes (from the PDF)

  • Architecture: single compact central +VBAT node, not dual banks, for a roughly 90 mm x 90 mm board.
  • Safety: main fuse should be upstream on the battery cable (recommended 225-250 A), close to the battery.
  • Copper strategy: use a short, wide, via-stitched central polygon (L1 + L3 for +VBAT), and strong common ground return (L2 + L4).
  • Copper thickness for the 200 A / 300 A rating: 1 oz (35 um) is not sufficient. Spec 2 oz (70 um) minimum on the outer layers, 3 oz preferred, and carry +VBAT and GND on two layers each in parallel (~4 oz-equivalent per net) with dense inter-layer via stitching. Treat the central node as a plane, not a trace, and size pours/vias for <= 20-30 C rise. Per-branch (~25 A): 2 oz outer with ~10-15 mm pour width is adequate.
  • Via stitching: use two via classes - large power vias (~1.2 mm pad / 0.6 mm drill or bigger) for the +VBAT node and ground return, and a smaller class (~0.6-0.8 mm pad / 0.3-0.4 mm drill) for signal-ground / thermal stitching around the PWM header.
  • Branch geometry: practical branch widths around 12-15 mm (8-10 mm absolute compact minimum for very short sections).
  • Connectors: dual XT90 input for current sharing (symmetrical wiring), XT60 per ESC branch preferred.
  • Protection/passives: 22-24 V standoff TVS class for 4S input, bulk capacitance near input/node plus branch-level capacitors.
  • Signal: 16-pin IDC PWM header with alternating PWM/GND and per-channel series + pulldown resistors.

Known Issues / TODO (V1.1)

  • No outstanding items. TVS placement, input HF cap grouping, indicator LEDs, and the R_BLEED1 value (now 22 kOhm) have all been resolved.

Quick Calculation Snapshot

  • Per thruster power at 16 V and 25 A: 400 W
  • System power for 8 thrusters: 3200 W
  • Example central copper section in the doc (50 mm width, 140 um thickness, 25 mm length, one layer):
    • Estimated R ~= 0.0616 mOhm
    • Vdrop at 200 A ~= 0.012 V
    • Copper loss at 200 A ~= 2.46 W

For complete assumptions, formulas, BOM guidance, and test plan, see Swim_Bladder_Doc_v3_0.pdf.

Screenshots (V1.1)

Assembled Board (1)Assembled Board (2)
Assembled SwimBladder PDB, angle 1Assembled SwimBladder PDB, angle 2
Routing3D Render - Top3D Render - Isometric
V1.1 routingV1.1 render, top viewV1.1 render, isometric view

Earlier V1.0 captures (Schematic.png, PCB Editor View.png, 3D View.png) remain in Screenshots/ for reference.

Getting Started

  1. Install KiCad (recommended version 8+).
  2. Open the project from KiCad Project Files v1.1/UWU PDB.kicad_pro.
  3. Review schematic, layout, and engineering assumptions from the PDF before fabrication, noting the V1.1 changes and open TODO items above.

Changelog

V1.1 (in progress)

  • Canonical project files moved to KiCad Project Files v1.1/; earlier KiCad Project Files/ and the repo-root SwimBladder PDB.kicad_sch are deprecated.
  • Added SwimBladder Custom Footprints library.
  • Main bulk capacitance specified as C_MAIN1/2 = 4700 uF each.
  • Removed the 1 nF per-branch decoupling cap; branches now use 1000 uF + 1 uF only.
  • PWM front-end defined: R_PWM* = 100 Ohm series, R_PD* = 10 kOhm pulldown, inputs J11..J18.
  • Added rail bleed resistor R_BLEED1 (value still a placeholder) and status LED D2 / R_LED1.
  • Input TVS D1 present; placement correction pending (see Known Issues).

V1.0

  • Initial 8-branch central star-node PDB layout.

Procurement (2-board build)

Bare PCB via JLCPCB; most components via LCSC (SwimBladder_LCSC_BatchBOM_v1.1.csv); full reference BOM in SwimBladder_BOM_v1.1.csv. JLCPCB and LCSC ship separately even though they're sister companies - no combined-box option outside of paying for JLC's PCBA assembly service.

Still need to source separately (not in the LCSC batch order)

  • R_BLEED1, 22k Ohm, 0603 (LCSC C114065) - MOQ is Min:100/Mult:100, not worth it for ~3 pieces; ask around for spares or buy loose.
  • R_LED1 + R_PD1..R_PD8, 10k Ohm, 0603 (LCSC C98220) - same MOQ issue, ~23 pieces needed.
  • 30 A mini blade fuse elements (x16) for F_ESC1..F_ESC8 - these plug into the Keystone 3568 holder (which is in the LCSC order) but the fuse element itself isn't an LCSC/electronics- distributor item; source from an automotive parts store or RC supplier.
  • F_ESC1..F_ESC8 fuseholders, Keystone 3568 (x8) - LCSC C5249699 was out of stock, dropped from the batch order; source from Digi-Key/Mouser instead.

Already owned, not in the order

  • D2 status LED
  • J2 IDC 2x08 header
  • R_PWM1..R_PWM8, 100 Ohm, 0402 (from sample book)

License

This project is licensed under the MIT License. See the LICENSE file for details.

Parts

67
QtyValueFootprintReferences
81 uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC_HF1, C_HF2, C_HF3, C_HF4, C_HF5, C_HF6, C_HF7, C_HF8
8100 OhmResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR_PWM1, R_PWM2, R_PWM3, R_PWM4, R_PWM5, R_PWM6, R_PWM7, R_PWM8
81000 µFCapacitor_THT:CP_Radial_D12.5mm_P5.00mmC_ESC1, C_ESC2, C_ESC3, C_ESC4, C_ESC5, C_ESC6, C_ESC7, C_ESC8
810k OhmResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR_PD1, R_PD2, R_PD3, R_PD4, R_PD5, R_PD6, R_PD7, R_PD8
830 AFuse:Fuseholder_Blade_Mini_Keystone_3568F_ESC1, F_ESC2, F_ESC3, F_ESC4, F_ESC5, F_ESC6, F_ESC7, F_ESC8
8XT60 ESCConnector_AMASS:AMASS_XT60PW-F_1x02_P7.20mm_HorizontalJ3, J4, J5, J6, J7, J8, J9, J10
24700 µFCapacitor_THT:CP_Radial_D16.0mm_P7.50mmC_MAIN1, C_MAIN2
2XT90Connector_AMASS:AMASS_XT90PW-M_1x02_P10.90mm_HorizontalJ1, J19
1100 OhmResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR_BLEED1
110k OhmResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR_LED1
1Conn_02x08_Odd_EvenConnector_IDC:IDC-Header_2x08_P2.54mm_VerticalJ2
1D_TVSDiode_SMD:D_SMCD1
1LEDLED_SMD:LED_1206_3216MetricD2
1LOGOSwimBladder Custom Footprints:uwuG***
1LOGOSwimBladder Custom Footprints:1G***
1PWM1Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ11
1PWM2Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ12
1PWM3Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ13
1PWM4Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ14
1PWM5Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ15
1PWM6Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ16
1PWM7Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ17
1PWM8Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ18

More from markantosa/swimbladder

1
  • 4 layers96.5 × 92.2 mmUWU PDB, the printed circuit board in 3D

    UWU PDB

    markantosa/swimbladder

    [SUTD SOAR] 8-Thruster Central Star-Node PDB for 8× Blue Robotics T200 + Basic ESC System

    77 parts1MIT

Similar boards

  • 4 layers22 × 15 mmAmp cpw hmc311, the printed circuit board in 3D

    Amp cpw hmc311

    loxodes/vna

    Under development open hardware microwave vector network analyzer

    67 parts205
  • 4 layers51.4 × 60.6 mmGb rp2040 cart, the printed circuit board in 3D

    Gb rp2040 cart

    deltabeard/DBGC

    A Game Boy cartridge using the Raspberry Pi RP2040 with RTC and MBC support.

    67 parts57
  • 4 layers100 × 40 mmMotor controller, the printed circuit board in 3D

    Motor controller

    reubenstr/zuko

    A quadruped robot dog!

    67 parts51MIT
  • 4 layers49 × 43 mmSk005-monitor resyncer, the printed circuit board in 3D

    Sk005-monitor resyncer

    mirdej/synkie

    The Synkie is a modular open source analog video processor, developed by Michael Egger, Max Egger and Flo Kaufmann

    67 parts47
  • 4 layers30 × 26.5 mmDriver tmc2208, the printed circuit board in 3D

    Driver tmc2208

    calithameridi/corevus

    High-flexibility, low-cost mechatronics controller for 3D printers

    67 parts25
  • 4 layers50.3 × 33 mm154-watch, the printed circuit board in 3D

    154-watch

    martinberlin/H-spi-adapters

    PCB design for SPI adapters (HATs)

    67 parts23
  • 4 layers82.3 × 37.2 mmRIDE, the printed circuit board in 3D

    RIDE

    LIV2/RIDE

    To add the A0 Bonus RAM to the system you will need to use the addram command included in the RIDE-Software adf/lha found under Releases.

    67 parts17
  • 4 layers76 × 76.5 mmNumbpad, the printed circuit board in 3D

    Numbpad

    calvin-mcd/travaulta

    topre pcb for the vault35

    67 parts16

Questions

How big is the UWU PDB PCB?

It measures 99.3 × 92.2 mm and has 4 copper layers, 2.02 mm thick.

What parts does the UWU PDB use?

67 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the UWU PDB KiCad files?

From the markantosa/swimbladder repository on GitHub, at the commit this page was made from: the board is KiCad Project Files v1.1/UWU PDB.kicad_pcb and its schematic KiCad Project Files v1.1/UWU PDB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the UWU PDB design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).