

Anc without 7805
ANC design files
- Size
- 35.7 × 54.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 91
- Pads
- 236
- Tracks, vias
- 486, 51
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 22 Apr 2026
- Updated
- 22 Apr 2026
Overview
Anc without 7805 is an open-source printed circuit board by manojr005, from the manojr005/PCB-design-files repository on GitHub. It is a 2-layer board of 35.7 × 54.5 mm with 70 parts on 91 nets, routed with 486 tracks and 51 vias.
It is built around the LM358, LD39015M12R and LD39015M18R, with the PV36W203C01B00 and ASFL1-12.288MHZ-EC-T among its other parts. Its parts include 29 capacitors, 20 resistors, 6 ICs, 2 connectors and 1 crystal.
Main components
5LM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierLD39015M12R
SOT-23-5L-40℃~+125℃@(Tj) 1 1.2V 150mA 18uA 29uVrms 5.5V 65dB@(1kHz) 80mV@(100mA) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-23-5L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD39015M18R
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 100mV@(100mA) 150mA 18uA 29uVrms 5.5V 62dB@(10kHz) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPV36W203C01B00
SIP-3P,9.6x5mm20kΩ 25 500mW ±10% ±100ppm/℃ SIP-3P,9.6x5mm Potentiometers, Variable Resistors ROHSBournsPotentiometers & Variable ResistorsASFL1-12.288MHZ-EC-T
SMD5032-4P-20℃~+70℃ 12.288MHz 15mA 3.3V HCMOS、TTL SMD5032-4P Crystal Oscillators ROHSAbraconCrystal Oscillators
README
README.mdAnalog Noise Cancellation PCB with I2S Audio Output
Overview
This project presents a custom-designed PCB for an Analog Noise Cancellation (ANC) system. The design uses dual microphones to capture desired voice and ambient noise, and processes them through an analog front-end using operational amplifiers to suppress noise before digitization.
The filtered analog signal is then fed into an audio codec, which converts it into a digital I2S stream for further processing by a processor or FPGA.
System Architecture
-
Primary Microphone (Voice Input) Captures the desired speech signal.
-
Secondary Microphone (Noise Reference) Captures environmental noise.
-
Analog Processing (Op-Amp Stage)
- Signal conditioning
- Phase inversion of noise signal
- Summation for noise cancellation
-
Audio Codec
- Converts analog signal → digital
- Outputs via I2S protocol
-
Digital Interface (I2S Output)
- Connected to processor / FPGA for further processing
Working Principle
The system is based on destructive interference:
- The noise signal is inverted using an op-amp.
- The inverted noise is summed with the original signal.
- Ideally, noise components cancel out, leaving clean voice.
Features
- Dual-microphone input (voice + noise reference)
- Analog noise cancellation using op-amps
- Pre-digitization noise suppression
- I2S digital audio output
- Compatible with FPGA / embedded processors
- Low-latency processing (pure analog front-end)
Hardware Components
- Operational Amplifiers (Op-Amps)
- Dual Microphones
- Audio Codec (I2S compatible)
- Passive Components (Resistors, Capacitors)
- Power Supply Regulation Circuit
Interfaces
-
Analog Inputs:
- Mic 1 (Voice)
- Mic 2 (Noise)
-
Digital Output:
- I2S (BCLK, LRCLK, DATA)
🛠️ Tools Used
- PCB Design: KiCad
👤 Author
Manoj R Electronics and Communication Engineering
Top Layer Layout
Bottom Layer Layout
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4, C7, C8, C9, C10, C11, C12, C13, C14, C18, C19, C20, C21 |
| 10 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11, R12, R13, R14, R15, R16, R19, R20, R21, R22 |
| 5 | 22 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R25, R26, R27, R28 |
| 5 | Conn_01x02_Socket | Connector_PinSocket_1.27mm:PinSocket_1x02_P1.27mm_Vertical | in_1, in_2, out__2, out_1, out_3 |
| 3 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R4, R5 |
| 3 | 10uf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C27, C28, C33 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP1, TP2, TP3 |
| 2 | 0.001uf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C25, C26 |
| 2 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C15, C23 |
| 2 | 100uf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C29, C30 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16, C24 |
| 2 | 47uf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C31, C32 |
| 2 | LM358 | KiCADv6:M08A | U5, U6 |
| 2 | MountingHole | MountingHole:MountingHole_3.5mm | H1, H2 |
| 2 | PV36W203C01B00 | PV36W203C01B00:TRIM_PV36W203C01B00 | RV1, RV2 |
| 1 | 0.01uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1 |
| 1 | 1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 47uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C22 |
| 1 | 9Ω | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23 |
| 1 | ASFL1-12.288MHZ-EC-T | ASFL1_12_288MHZ_EC_T:XTAL_ASFL1-12.288MHZ-EC-T | Y1 |
| 1 | Conn_02x20_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Horizontal | J6 |
| 1 | LD1117S33TR_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | LD39015M12R | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | LD39015M18R | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | MAX98090AETL_T | MAX98090AETL_T:QFN40P500X500X80-41N | U1 |
| 1 | Screw_Terminal_01x02 | 282836_2:TE_282836-2 | J3 |
Similar boards
- 2 layers46.1 × 58.8 mm

- 4 layers310 × 210 mm

- 4 layers65 × 45.4 mm

Kimchi ulid
adamjvr/kimchi-HiFi-lid
A lid for the Kimchi SBC that provides: Stereo audio ouptut/input, mic in, and headphone output.
51 parts1 - 2 layers136.5 × 81.5 mm

- 2 layers46.9 × 46.6 mm

Fourth
Bhakti-A/Maya_V_FlightController
This is a custom flight controller PCB designed for drones.
84 parts1 - 2 layers48.1 × 48 mm

- 4 layers45.5 × 69.7 mm

Astrum
LtBrain/astrum
A control system board/robot for Science Olympiads Robot Tour. It will have 2 brushed motor drivers, at least 2 encoder inputs, and support for ultrasonic and TOF sensors, all in a compact package.
77 partsMIT - 2 layers53.3 × 54.9 mm

Questions
How big is the Anc without 7805 PCB?
It measures 35.7 × 54.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Anc without 7805 use?
70 parts, built around the LM358, LD39015M12R, LD39015M18R and PV36W203C01B00. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Anc without 7805 KiCad files?
From the manojr005/PCB-design-files repository on GitHub, at the commit this page was made from: the board is anc_without_7805.kicad_pcb and its schematic Analog_anc_input.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Anc without 7805 design in my own project?
Its repository states no licence, so its author keeps all rights: ask manojr005 before reusing the design.