Skip to the content
2 layers100.1 × 49.9 mmRC2014-Ethernet, the printed circuit board in 3D

RTL8019 Ethernet card for the RC2014 Z80 computer

Size
100.1 × 49.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
29
Nets
93
Pads
244
Tracks, vias
286, 94
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
25 Aug 2020
Updated
19 Mar 2021

Overview

RC2014-Ethernet is an open-source printed circuit board by Manawyrm, from the Manawyrm/RC2014-Ethernet repository on GitHub. It is a 2-layer board of 100.1 × 49.9 mm with 29 parts on 93 nets, routed with 286 tracks and 94 vias.

It is built around the RTL8019AS-LF and 13F-39MNL. Its parts include 11 capacitors, 7 resistors, 3 connectors, 2 ICs and 1 crystal. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

README.md

RC2014 RTL8019 Ethernet card

RTL8019 network card

The design is optimized for automated assembly at JLCPCB.

Schematic
Firmware

Rev. A Errata:

  • Reset polarity is wrong, reset trace needs to be cut and wired to VCC (reset is done in software)
  • Interrupt polarity is also wrong, remove R7. (to use interrupts, use an N-channel MOSFET to drive the INT line. Untested!)
  • RTL8019 requires an SPI 9346 EEPROM for it's configuration data (for full-duplex ethernet, correct function of the LEDs, proper MAC addresses), which is missing
  • RTL8019 footprint is wrong (too small). JLCPCB can still assemble these boards, but it's marked as a manufacturing error.

Parts

29
QtyValueFootprintReferences
5100nCapacitor_SMD:C_0402_1005MetricC7, C8, C9, C10, C11
41nFCapacitor_SMD:C_1206_3216MetricC1, C2, C5, C6
21kResistor_SMD:R_0402_1005MetricR5, R6
2200RResistor_SMD:R_0402_1005MetricR4, R7
220pCapacitor_SMD:C_0402_1005MetricC3, C4
2MountingHoleToolingHole:ToolingHole_JLCSMTH1, H2
110kResistor_SMD:R_0402_1005MetricR3
113F-39MNLPackage_SO:SOIC-16W-12_7.5x10.3mm_P1.27mmT1
11MResistor_SMD:R_0402_1005MetricR2
120MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
127kResistor_SMD:R_0402_1005MetricR1
174LS138Package_SO:SOIC-16_3.9x9.9mm_P1.27mmU2
18P8C_ShieldedConnector_Ethernet:8P8C_yellow_green_Ckmtw_C133529J2
1AddressConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ3
1Ferrite_BeadInductor_SMD:L_0805_2012MetricFB3
1IOCHRDYTestPoint:TestPoint_Pad_2.5x2.5mmTP1
1RC2014_BUSConnector_PinHeader_2.54mm:PinHeader_1x39_P2.54mm_VerticalJ1
1RTL8019ASPackage_QFP:PQFP-100_14x20mm_P0.65mmU1

Similar boards

  • 2 layers157.4 × 74.2 mmISA8019, the printed circuit board in 3D

    ISA8019

    Manawyrm/ISA8019

    RTL8019-based ISA network card, NE2000-compatible

    56 parts129GPL-3.0
  • 2 layers85.7 × 132.2 mmXt cf tandy, the printed circuit board in 3D

    Xt cf tandy

    retrotheory/tandy-XT-CF-Lite-LAN

    Tandy XT-CF-Lite LAN Rev 0.9a ReadMe ---------------------------- This is a Compact Flash HD and Realtek LAN card for the Tandy 1400. It uses the expansion slot on the rear of the Tandy to add a bootable HD.

    44 parts8GPL-3.0
  • 2 layers104.1 × 71.9 mmISA8019, the printed circuit board in 3D

    ISA8019

    kitspace-test-repos/kicad6-file-collection

    57 partsMIT
  • 4 layers239.4 × 165.7 mmMAXI030, the printed circuit board in 3D

    MAXI030

    aslak3/MAXI030

    MC68030 based expandable computer design

    222 parts38GPL-2.0
  • 2 layers100 × 64.8 mmObsonet 1, the printed circuit board in 3D

    Obsonet 1

    cristianoag/obsonet

    Repository to host source files for the Obsonet Reloaded

    35 parts4
  • 2 layers103.8 × 73.2 mmRTL8019, the printed circuit board in 3D

    RTL8019

    Vakon84/Chanterelle-RTL8019AS

    58 parts
  • 2 layers104.1 × 74.9 mmISA8 Ethernet, the printed circuit board in 3D

    ISA8 Ethernet

    Vakon84/isa8_eth

    If EEPROM has not been programmed prior to assembly, now it is a good time to do so. The U3 EEPROM contains the following configuration for the RTL8019AS chip: MAC address ISA resources for jumperless configuration Base…

    34 partsCERN-OHL-S-2.0
  • 2 layers100 × 100 mmZ80ENET, the printed circuit board in 3D

    Z80ENET

    lynchaj/nhyodyne

    Modular Backplane Computer

    48 parts31

Questions

How big is the RC2014-Ethernet PCB?

It measures 100.1 × 49.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the RC2014-Ethernet use?

29 parts, built around the RTL8019AS-LF and 13F-39MNL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the RC2014-Ethernet KiCad files?

From the Manawyrm/RC2014-Ethernet repository on GitHub, at the commit this page was made from: the board is RC2014-Ethernet.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the RC2014-Ethernet design in my own project?

Its repository states no licence, so its author keeps all rights: ask Manawyrm before reusing the design.