Skip to the content
2 layers49.9 × 99.9 mmLed segment, the printed circuit board in 3D

PoV globe

Size
49.9 × 99.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
52
Nets
39
Pads
226
Tracks, vias
878, 135
Pours
1
Routed
Yes
KiCad
KiCad 3
Created
13 Jun 2014
Updated
19 Oct 2014

Overview

Led segment is an open-source printed circuit board by makers-ie, from the makers-ie/pov-globe repository on GitHub, published under the MIT licence. It is a 2-layer board of 49.9 × 99.9 mm with 52 parts on 39 nets, routed with 878 tracks and 135 vias.

It is built around the FDV301N. Its parts include 32 diodes, 7 resistors, 6 transistors, 4 connectors and 2 capacitors.

Main components

1

README

README.md

PoV Globe

Persistence of vision globe project.

Requirements

  • Use an FPGA
  • The size should be noticable
  • Rotation should be well balanced
  • Should be easy to interface with from a PC

Design

  • One ring of LEDs, stuck on a pivoting axis.
  • Ring diameter 50 cm is noticable.
  • Stepper motor to drive the ring, for speed control.
  • Encoder to avoid drifting.
  • RGB LEDs
  • Stick LEDs on both halves of the ring for better balance.
  • Shift LEDs on one half one half-LED for increased resolution.
  • Use wireless for interfacing, so we don't have to transfer high-bandwidth data to the rotor.
    • Bluetooth module is suggested.
    • NRF24L01 pair with Teensy USB interface suggested.
  • Build PCB ring segments with SMD LEDs mounted on the edge.

Limits

  • Ring diameter 50 cm; circumference 1.6 m
  • PLCC4 RGB LEDs are 3.5x2.8 mm; maximum resolution is 9 dpi
  • With interlacing; maximum resolution is 18 dpi
  • At 18 dpi, would use 535 LEDs
  • Divide circle into 16 sectors, ignore the two bottom sectors
  • Each sector has 32 LEDs, for a total of 64 LEDs ignored
  • In total, we have 448 LEDs
  • Control for RGB needs 1,344 channels
  • Spin ring at 60 rps
  • We should have the same resolution both horizontally and vertically
  • Each slice must update 1,344 channels
  • FPGA board has 42 I/O pins
  • Divide channels into matrix of 32x42
  • With a shift-register column driver, this requires 34 FPGA connections
  • Each slice must update 42 columns; FPGA scans at 1.3 MHz
  • With RGB555; 32 shades per base color; FPGA runs PWM at 42 MHz
  • With RGB555; framebuffer memory is 572 kB; with double-buffering 1.14 MB

Mechanical

  • A ring divided into 16 sectors, each with a PCB
  • Cross-bars horizontally and vertically for rigidity
  • Stepper-motor located in center of ring to avoid unbalanced twisting forces
  • Plastic fasteners to attach cross-bars to stepper motor and ring PCBs
  • Ring PCBs on one side shifted 1/2 LED for interlacing
  • Foundation in reinforced concrete with a fixed steel axis extending to the stepper motor
  • Steel axis connected to stepper motor with locking pin?
  • FPGA board located in the lower part of the ring to utilize the space created by not having LED PCBs there
  • Stepper motor driver could be counter-weight for FPGA board
  • One (or two?) ball bearings in the lower ring part
  • Ball bearings inside copper pipe or plastic to make it easy to fasten the ring PCBs and FPGA
  • We can run ground in the fixed steel axis, unless the stepper motor is weird
  • If one ball bearing is insulated from the fixed axis, the other pole can go through the bearing
  • Hall/optical-sensor for motor auto-calibration (1 pulse/revolution)
  • Ring PCBs
    • Copper traces going to the edge, connecting by direct soldering should be rigid and good
    • We will be running MHz signals, so 4-layer PCB is probably needed to have a full ground plane

Electrical

  • We should be fine with 5 V
    • FPGA board needs Vcc = 5 V
    • LEDs are Vf <= 3.5 V
    • Stepper motor (42BYGHW609, NEMA 17?) needs 3.4 V (resistive)
  • Current usage is max 3 A
    • FPGA likely less than 100 mA
    • LEDs are Ifm < 32*25 mA < 1 A
    • Stepper motor can do 1.7 A (resistive)
  • Power usage is max 15 W
  • Components
    • Stepper motor driver
    • Power supply 5V/15W
    • Ring sector PCBs x14
    • FPGA interface PCBs x2
      • Ring-side PSU filter
      • Hall/optical-sensor
      • Stepper motor driver
      • LED row drivers
  • Each ring PCB will have 32x3 channels
    • With 16 rows, this means 6 columns
    • We split the PCB in two column groups and drive each color as a column, i.e. a 2x3 column configuration
    • Need a 6-bit high-speed shift register, f <= 42 MHz, 23 ns per cycle
    • Prefer ICs that can drive 25 mA LEDs by themselves
    • Candidate is 74VHC595, Iout <= 25 mA, Vcc <= 5.5 V, f <= 155 MHz
  • FPGA I/O, 48 max
    • 1 Rotation sensor (analog?)
    • 2 LED columns (clock, data)
    • 3 Communications (SPI)
    • 4 Stepper motor output (Bipolar H-bridge)
    • 32 LED rows
    • Max IOH 24 mA when using LVCMOS33 outputs. Datasheet, page 10.

Datasheets

These are components which we already have:

Candidates for new parts:

Parts

52
QtyValueFootprintReferences
32PLCC4RGBCT-CAplcc4-edgeLED1, LED2, LED10, LED11, LED12, LED13, LED14, LED15, LED16, LED17, LED18, LED19, LED20, LED21, LED22, LED23 +16
7RSM0603R1, R2, R3, R4, R5, R6, R7
6FDV301NSOT23GDSQ1, Q2, Q3, Q4, Q5, Q6
2CSM0603_CapaC1, C2
2CONN_20boardedge_20P2, P4
2CONN_3boardedge_3P1, P3
174164ssop-16U1

Similar boards

  • 12 layers160.1 × 233.5 mmVme wren, the printed circuit board in 3D

    Vme wren

    KiCad/kicad-source-mirror

    This is an active mirror of the KiCad development branch, which is hosted at GitLab (updated every time something is pushed). Pull requests on GitHub are not accepted or watched.

    1,508 parts3.1kGPL-3.0
  • 2 layers88 × 102 mmToniebox v1v2, the printed circuit board in 3D

    Toniebox v1v2

    toniebox-reverse-engineering/toniebox-pcb

    KiCad schematic of the Toniebox PCB (including datasheets).

    11 parts37
  • 4 layers73.4 × 72.7 mmAwatch2, the printed circuit board in 3D

    Awatch2

    jwise/aWatch2-hw

    hardware for aWatch2

    177 parts18
  • 4 layers229 × 157 mmOMower, the printed circuit board in 3D

    OMower

    vasimv/OMower

    SDK for open-source open-hardware 2/4 wheels robots platform

    421 parts11GPL-3.0
  • 6 layers90 × 180 mmDvk mx8m bsb, the printed circuit board in 3D

    Dvk mx8m bsb

    gralco/dvk-mx8m-bsb

    Librem 5 Developer Kit using EmCraft's i.MX 8M System-on-Module.

    684 parts7GPL-3.0
  • 2 layers58 × 63 mmCamping LightRelay, the printed circuit board in 3D

    Camping LightRelay

    Rustaphor/LightRelay4Camping

    Analog light sensor to night power up LED garland. For Camping use.

    91 parts2GPL-3.0
  • 6 layers130.3 × 100 mmNoob sdr, the printed circuit board in 3D

    Noob sdr

    ainnovators/noob-sdr

    An open source SDR board derived from Michael Ossmann's Hackrf project. It should include an onboard FPGA for DSP purposes.

    473 parts1GPL-3.0

Questions

How big is the Led segment PCB?

It measures 49.9 × 99.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Led segment use?

52 parts, built around the FDV301N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Led segment KiCad files?

From the makers-ie/pov-globe repository on GitHub, at the commit this page was made from: the board is electrical/led-segment.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Led segment design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).