2 layers116.8 × 92.2 mm
2 layers100.1 × 100.1 mm
Horno
m4v/Proyecto-finalProyecto Final - Cátedra de Ingeniería Electronica - 2016
- Size
- 100.1 × 100.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 51
- Nets
- 87
- Pads
- 240
- Tracks, vias
- 526, 19
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 20 Jun 2016
- Updated
- 2 Dec 2016
Overview
Horno is an open-source printed circuit board by m4v, from the m4v/Proyecto-final repository on GitHub, published under the MIT licence. It is a 2-layer board of 100.1 × 100.1 mm with 51 parts on 87 nets, routed with 526 tracks and 19 vias.
It is built around the OP07, L293D and LTC1050CP, with the LM35 and BC547 among its other parts. Its parts include 15 capacitors, 10 resistors, 9 connectors, 6 ICs and 1 transistor. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
5
OP07
SOP-8-20℃~+85℃ -22V~-3V、3V~22V 1 1.8nA 1.8uV/℃ 10nV/√Hz@1kHz 120dB 15pA/℃ 170V/ms 2.7mA 22V 500kHz 60uV 800pA SOP-8 Operational Amplifier ROHSSlkorOperational Amplifier
L293D
DIP-16-40℃~+150℃ 1.2A 2 4.5V~36V 4mA 600mA DIP-16 Brushed DC Motor Drivers ROHSSTMicroelectronicsStepper Motor DriverLTC1050CP
-- Operational Amplifier ROHSTexas InstrumentsOperational Amplifier
LM35
TO-92UncategorisedSilicore
BC547
TO-92Bipolar (BJT)Jiangsu Changjing Electronics Technology (CJ)
README
README.mdProyecto Final - Cátedra de Ingeniería Electrónica - 2016
El objetivo de este proyecto es diseñar un sistema de control digital para un horno de prótesis dentales.
Contenido del repositorio
- firmware/ - Directorio con el programa del horno.
- horno/ - Código fuente específico del horno.
- lpc_board_nxp_lpcxpresso_1769/ - Biblioteca de la placa LPCxpresso 1769.
- lpc_chip_175x_6x/ - Biblioteca del microcontrolador LPC1769.
- periph_*/ - ejemplos de LPCOpen.
- kicad/ - Archivos del esquemático y PCB
- datasheet/ - documentación de los integrados utilizados.
- notas de aplicaciones/ - documentación sobre temas relevantes al proyecto.
- documentación/ - archivos del horno en formato .pdf. Ej. esquemáticos
- pcb/ - pdfs de las capas del circuito impreso.
- mediciones/ - Archivos .csv con los resultados de mediciones hechas.
- graficos/ - Gráficos de las mediciones hechas.
- NOTAS.txt - información sobre algunas mediciones.
- octave/ - scripts de Octave
- matlab/ - archivos de simulink y del identificador de sistemas.
Autores
- Gastón Riera
- Elián Hanisch
- Rodrigo Oliver
Parts
51| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0,1uF | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C5, C7, C9, C11, C14 |
| 4 | 0.1uF | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C6, C8, C10, C12 |
| 4 | 220nF | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C1, C2, C3, C4 |
| 3 | 56k | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R2, R3, R7 |
| 3 | OP07 | Housings_DIP:DIP-8_W7.62mm_LongPads | U1, U2, U4 |
| 3 | POT | Potentiometers:Potentiometer_Bourns_3005_Angular_ScrewFront | RV1, RV2, RV3 |
| 2 | 330k | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R4, R8 |
| 2 | R | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R9, R10 |
| 1 | 1,5k | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R5 |
| 1 | 10k | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R1 |
| 1 | 120k | Resistors_ThroughHole:Resistor_Horizontal_RM10mm | R6 |
| 1 | 1uF | Capacitors_ThroughHole:C_Radial_D5_L6_P2.5 | C13 |
| 1 | 24V | Pin_Headers:Pin_Header_Straight_1x02 | P5 |
| 1 | Alimentación | Pin_Headers:Pin_Header_Straight_1x03 | P10 |
| 1 | BC547 | TO_SOT_Packages_THT:TO-92_Inline_Wide | Q1 |
| 1 | C | Capacitors_ThroughHole:C_Disc_D3_P2.5 | C15 |
| 1 | GPIO | Pin_Headers:Pin_Header_Straight_2x12 | P9 |
| 1 | L293D | Housings_DIP:DIP-16_W7.62mm_LongPads | U5 |
| 1 | LM35 | TO_SOT_Packages_THT:TO-92_Inline_Wide | U6 |
| 1 | LPC1769 | Horno:Pin_Header_LPCXpresso_LPC1769 | P1 |
| 1 | LTC1050 | Housings_DIP:DIP-8_W7.62mm_LongPads | U3 |
| 1 | Lm1 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W1 |
| 1 | Lm2 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W2 |
| 1 | Lm3 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W3 |
| 1 | Motor | Pin_Headers:Pin_Header_Angled_1x05 | P6 |
| 1 | Pantalla | Pin_Headers:Pin_Header_Straight_2x11 | P7 |
| 1 | RST | Buttons_Switches_ThroughHole:SW_PUSH_6mm | SW1 |
| 1 | TRIAC | Pin_Headers:Pin_Header_Straight_1x02 | P4 |
| 1 | Termocupla | Connect:bornier2 | P3 |
| 1 | Th1 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W4 |
| 1 | Th2 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W5 |
| 1 | Th3 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | W6 |
| 1 | UART | Pin_Headers:Pin_Header_Straight_1x03 | P8 |
Questions
How big is the Horno PCB?
It measures 100.1 × 100.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Horno use?
51 parts, built around the OP07, L293D, LTC1050CP and LM35. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Horno KiCad files?
From the m4v/Proyecto-final repository on GitHub, at the commit this page was made from: the board is kicad/horno.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Horno design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers245.6 × 85.9 mm
- 2 layers60 × 90 mm
- 2 layers95 × 95 mm
- 2 layers88.9 × 73.2 mm
- 2 layers99.6 × 50.4 mm
- 2 layers210 × 125 mm
Controller bldc
david8128/Electeam-Sharky
Firmware designed in ESP32 DEVKIT microcontroller where motor, throttle, breaks, Nextion touch screen and more systems are integrated.
73 parts2GPL-3.0 - 2 layers100 × 50 mm
Carga Electronica
kr4fty/Carga-Electronica-STM32
Desarrollo de un Sistema de Control PID para una Carga Electrónica utilizando un STM32
49 parts1