Skip to the content
2 layersTestTarget, the printed circuit board in 3D

AVR-Based easily modifyable DIY Lasertag!

Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
16
Pads
39
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 4
Created
20 Feb 2016
Updated
2 Jan 2023

Overview

TestTarget is an open-source printed circuit board by lzrtag, from the lzrtag/LZRTag repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 13 parts on 16 nets.

It is built around the ATTINY13A-PU. Its parts include 5 resistors, 4 diodes, 1 IC, 1 connector and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

LZRTag

ESP32-Based Lasertag

Ever wanted to set up your own system of Lasertag? Interested in having an easily modifiable system to create your own gamemodes and styles with? Or just looking for a cool project to try out? Well, why not take a spin at this!

Note: This project is not in serious development. I (Xasin) take no responsibility for what is done with this code, and I can't guarantee it'll do exactly what I tell it to (even if I try to give it treats >:c) However, it is a fully functional system, if you know how to use it, and it has proven itself to be pretty reliable and useful!

The components

In order to have a functional game, you will need at least the following:

  • Two or more soldered Lasertag Sets
  • A WiFi access point or a newtwork of points throughout the arena.
  • A MQTT Server, preferrably in the local network, to reduce ping.
  • And a system running Ruby 2.4 or better, to run the Lasertag Backend and your gamemodes

The Electronics

Attention: The electronics aren't necessarily beginner-friendly. I've designed them with components no smaller than a TSOP package or a 0805 resistor, but the newer versions of the hardware do include two QFN Packages - one for a optional IMU, so it can be left out, and one for a standard I2S audio chip, for which you can use any breakout board that supports 44100Hz, 16 bit playback. If you have a hot air gun, definitely make use of it!

The electronics are based around the ESP32, a fairly cheap, powerful, WiFi and Bluetooth capable chip. The PCB includes all necessary support structures, including a battery charge circuit and a USB to UART converter to reprogram and debug the ESP. It comes with the following hardware:

  • The ESP32 plus beefy voltage regulation, ESD protection, etc. It ain't gonna break!
  • A MAX I2S decoder + amplifier, for on-board, high quality audio.
  • A LSM6D IMU, to detect movement, collisions, gestures, etc.
  • Peripherals to receive and send IR Signals (documented here: TODO)
  • Feedback in the shape of WS2812 LEDs and a vibration motor
  • Trigger, Gun Select and Reload buttons.

The vest connection is exposed with a D-SUB connector, and I2C lines are available to make more complex add-ons easier to achieve. There's also a I2C breakout connection on the PCB itself!

The Vest itself can be as simple as a couple of Vishay 40kHz IR receivers and WS2812 LEDs, but there is a connection for vest-specific haptic feedback, and via the I2C connection it's easy to add more complex features.

To solder one, check out the Aisler project here: https://aisler.net/p/QLILZEMV Or head to the "Electronics" folder and generate your own Gerber files!

The Casing

The 3D printed casing I designed is totally optional - the electronics can be easily fitted into any other casing, provided it has space for a switch, a speaker and a couple of LEDs! However, if you do want to print it out, there's the Fusion360 page here: https://a360.co/2Lbm2zJ

Parts

13
QtyValueFootprintReferences
3470ΩDiscret:R1R1, R2, R3
2DDiscret:R1D2, D4
11MΩDiscret:R1R4
15KΩDiscret:R1R5
1ATTINY13A-PHousings_DIP:DIP-8_W7.62mmIC1
1BatteryPin_Headers:Pin_Header_Straight_1x02BT1
1CONN_02X03Pin_Headers:Pin_Header_Angled_2x03P1
1LED-GLEDs:LED-3MMD3
1LED_RCBGPin_Headers:Pin_Header_Straight_1x04D1
1SPSTPin_Headers:Pin_Header_Straight_1x03SW1

More from lzrtag/LZRTag

3
  • 2 layers57.2 × 35.1 mmMainBoard Rev2, the printed circuit board in 3D

    MainBoard Rev2

    lzrtag/LZRTag

    AVR-Based easily modifyable DIY Lasertag!

    70 parts111GPL-3.0
  • 2 layers57.8 × 31.1 mmLZRTag, the printed circuit board in 3D

    LZRTag

    lzrtag/LZRTag

    AVR-Based easily modifyable DIY Lasertag!

    30 parts111GPL-3.0
  • 2 layers28.4 × 21.3 mmSensorBoard, the printed circuit board in 3D

    SensorBoard

    lzrtag/LZRTag

    AVR-Based easily modifyable DIY Lasertag!

    8 parts111GPL-3.0

Similar boards

  • 2 layers99.7 × 63.9 mmNES CN ROM-256-05, the printed circuit board in 3D

    NES CN ROM-256-05

    emeargt/nes-cnrom

    KiCad project for NES-CN-ROM-256-05 cartridge schematic and PCB

    17 parts31CC-BY-SA-4.0
  • 2 layers100 × 61.4 mmCart, the printed circuit board in 3D

    Cart

    digilogistist/The-Open-Source-USB-NES-Project

    USB-NES and NES-FASTGFX product engineering repository

    38 parts24CC0-1.0
  • 2 layers100 × 100 mmMotherboard, the printed circuit board in 3D

    Motherboard

    Terminus-IMRC/RPiCluster2

    Yet another Raspberry Pi cluster, version 2

    334 parts9
  • 2 layers22.9 × 30.7 mmOnewire led, the printed circuit board in 3D

    Onewire led

    kcuzner/onewire-leds

    An RGB LED driver on a modified one-wire bus

    11 parts4MIT
  • 4 layers243.8 × 243.8 mmSbc 8088, the printed circuit board in 3D

    Sbc 8088

    miselin/M88

    The M88 Computer

    218 parts2CERN-OHL-P-2.0
  • 6 layers100.1 × 112 mmPicones, the printed circuit board in 3D

    Picones

    WiiMake/picones

    In the last 40 years, technology has advanced to the point were what used to be done in hardware can now be done in software. This project uses an rp2350 to emulate a ROM chip on an NES Cartridge.

    59 parts1
  • 2 layers27.9 × 15.2 mmFF2 20241213 1510, the printed circuit board in 3D

    FF2 20241213 1510

    25mmHg/AlteFabrik191126

    Flimmerfeen2.0

    12 partsBSD-3-Clause
  • 2 layers140 × 60 mmA277d led tachometer, the printed circuit board in 3D

    A277d led tachometer

    bazsimarkus/a277d-led-tachometer

    An analog LED tachometer controlled by an East German A277D chip (clone of UAA180), featuring an integrated ATtiny13A-based digital ignition pulse generator for testing.

    61 parts

Questions

What parts does the TestTarget use?

13 parts, built around the ATTINY13A-PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the TestTarget KiCad files?

From the lzrtag/LZRTag repository on GitHub, at the commit this page was made from: the board is Electronics/TestTarget/TestTarget.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the TestTarget design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).