Skip to the content
2 layers25.1 × 25 mmNoncontact electrodes, the printed circuit board in 3D

Noncontact electrodes

logical/telepathy10

Telepathy is a wireless eeg device.

Size
25.1 × 25 mm
Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
10
Pads
26
Tracks, vias
30, 0
Pours
1
Routed
Yes
KiCad
KiCad 3
Created
13 Nov 2014
Updated
20 Jan 2018

Overview

Noncontact electrodes is an open-source printed circuit board by logical, from the logical/telepathy repository on GitHub. It is a 2-layer board of 25.1 × 25 mm with 13 parts on 10 nets, routed with 30 tracks and 0 vias.

It is built around the LMP7702MA. Its parts include 6 connectors, 3 capacitors, 3 resistors and 1 IC.

Main components

1

README

README.md

THIS PROJECT IS DISCONTINUED FOR NOW.

The research is proving more difficult than I have hoped and there are alternatives available.

This is telepathy the mostly HARDWARE project not telepathy the software project Sorry for my lack of creativity in choosing a name.

This poject contains an EXPERIMENTAL wireless eeg circuit.

GOAL

This project is under development so it is not working. I welcome suggestions.

The goal is to do brain computer interface experments.I want to make a wireless headband that runs on a battery.

It contains.

STATUS

I made one pcb but it didn't work. I'm still interested in the project so I am currently doing a complete redesign of the hardware. I will be etching the boards myself they will be single sided SMT and divided in sections.Here are some of the changes I'm planning.

  1. Split the device into sections for power, amplifier and input/output.
  2. Replace the wireless module and pic with a wireless capable microcontroller. (telepathy with esp8266?)
  3. The whole design will be based on active electrodes.

ELECTRODES:

I have 2 designs for active electrodes. Active dry electrodes and active noncontact electrodes. The dry electrodes are based on the openeeg design. The noncontact electrodes are based on a design I found here:

http://www.isn.ucsd.edu/pubs/bsn10.pdf

I'm assuming it is creative commons.

AMPLIFIER BOARD:

The amplifier board is under testing I plan to use one filter for aliasing and filter the rest in software. None of the resistor and capacitor values are decided yet.
I have the source voltage at 3.3v from a cell phone battery. So far I can pick up a heartbeat .

EEGDATA:

A GUI software program for linux that retreives the data from the /dev/rfcomm0 bluetooth serial terminal and analyzes and displays the data. I started the project in C but it was more convenient to write the data analysis portion in C++.

On my system I use these commands to setup the bluetooth serial port.

text
#find the address
$hcitool scan
#bind the address
$sudo rfcomm bind rfcomm0 device_address

For BLE

text
#find the adapter address
$hcitool dev
#find the device address
$sudo hcitool -i hci0 lescan

Then you need to run any programs that access serial terminal as root unless you have sufficient permission.

FIRMWARE:

The firmware is for a PIC microcontroller 16f1788 and a bluetooth serial module hc-05.

I have wrote a bootloader so I can more easily install firmware.The bootloader sets the hc-05 up at 38400 and waits for a program. When the program successfully loads it sets a byte in ee memory.when the FLASH command is sent to the program it erases the byte so the bootloader will again wait for a progam. You can use a standard serial terminal to send the program but you have to set a long delay (~30ms) between characters so the program has time to write. Custom coding the serial interface for the bootloader would be faster but this works for now.

Hopefully I have no glitches in the bootloader or a firmware update could brick the device! If so the glitch would have to be fixed and the bootloader reprogrammed.

The microcontroller first sets up the hc-05 at 230400, then wait for a request.When it receives a request it begins sampling the analog to digital converter and sending the samples to the hc-05.

I have included the makefiles so they should build with the make command but they may require modification . MPLABX should be able to load them as a makefile project but I have not tried.

SCHEMATIC:

I'm developing the amplifier board first. amplifier-board.png is the current design.

DISCLAIMER:

This project is an EXPERIMENT. I make no claims that it actually does anything.It may be harmful to individuals or property. THIS DEVICE AND SOFTWARE MAY BE DANGEROUS. DO NOT BUILD IT.

Parts

13
QtyValueFootprintReferences
5CONN_11PIN_SMDP2, P3, P4, P5, P6
1.22upfc_0805C3
1100SM0805R3
1100nfc_0805C2
110kSM0805R1
110nfc_0805C1
11MegSM0805R2
1CONN_1PIN_ARRAY_1P1
1lmp7702SO8EU1

More from logical/telepathy

2
  • 2 layers70.1 × 50 mmAmp board, the printed circuit board in 3D

    Amp board

    logical/telepathy

    Telepathy is a wireless eeg device.

    35 parts10
  • 2 layers15.6 × 14.7 mmActive electrode, the printed circuit board in 3D

    Active electrode

    logical/telepathy

    Telepathy is a wireless eeg device.

    13 parts10

Similar boards

  • 2 layers139.7 × 41.9 mmKstat mainboard, the printed circuit board in 3D

    Kstat mainboard

    nfroehberg/GlazerLab_KStat

    Firmware, PCB design and Python interface for the KStat potentiostat developed in the Glazer Lab, University of Hawaii.

    121 parts
  • 2 layers40 × 20 mmUsb uart, the printed circuit board in 3D

    Usb uart

    earthtojake/text-to-cad

    Design physical products with AI

    13 parts26kMIT
  • 2 layers35 × 29 mmMagSpoofTC, the printed circuit board in 3D

    MagSpoofTC

    samyk/magspoof

    A portable device that can spoof/emulate any magnetic stripe, credit card or hotel card "wirelessly", even on standard magstripe (non-NFC/RFID) readers.

    13 parts4.2k
  • 2 layers20.6 × 23.6 mmAO-03 signal amplifier, the printed circuit board in 3D

    AO-03 signal amplifier

    fossasia/pslab-scripts

    Pocket Science Lab - Scripts for Sensor Experiments

    13 parts1.6kApache-2.0
  • 2 layers47 × 35.6 mmMX7-C-35PL C11, the printed circuit board in 3D

    MX7-C-35PL C11

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    13 parts1.2k
  • 2 layers95 × 95 mmCube batteryboard, the printed circuit board in 3D

    Cube batteryboard

    willem-pennings/balancing-cube

    A cube that balances itself in a corner or edge using reaction wheels

    13 parts1.1kGPL-3.0
  • 2 layers15.2 × 20.3 mmPt100stick, the printed circuit board in 3D

    Pt100stick

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    13 parts1.1kGPL-3.0

Questions

How big is the Noncontact electrodes PCB?

It measures 25.1 × 25 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Noncontact electrodes use?

13 parts, built around the LMP7702MA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Noncontact electrodes KiCad files?

From the logical/telepathy repository on GitHub, at the commit this page was made from: the board is noncontact-electrodes/noncontact-electrodes.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Noncontact electrodes design in my own project?

Its repository states no licence, so its author keeps all rights: ask logical before reusing the design.