Skip to the content
2 layers99.8 × 50 mmAQM AGS10, the printed circuit board in 3D

Battery-powered indoor air quality monitor that reads VOC every 60 seconds and displays it on an e-ink screen.

Size
99.8 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
26
Nets
22
Pads
63
Tracks, vias
119, 13
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 May 2026
Updated
15 Sep 2026

Overview

AQM AGS10 is an open-source printed circuit board by lmiez, from the lmiez/AGS10-VOC-Monitor repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 99.8 × 50 mm with 26 parts on 22 nets, routed with 119 tracks and 13 vias.

It is built around the MCP73831T-2ACI/OT-HXY. Its parts include 6 resistors, 3 capacitors, 3 ICs and 2 diodes. It belongs with the lEDs and displays and power boards and the RP2040 boards of this library.

Main components

1

README

README.md

air quality monitor-bom.csv

AGS10-VOC-Monitor

Battery-powered indoor air quality monitor that reads VOC every 60 seconds and displays it on an e-ink screen.

Functionality

It uses an AGS10 TVOC sensor which samples the air every 60 seconds, when it's not sampling it goes into a sleep mode where the resistive heater turns off, the PCB includes an MCP73831 which charges LiPo batteries at 0.5A which is perfect for a 500mAh or 800mAh LiPo (1C/0.625C charge rate) The MCU is the seeed studios RP2040 which has a trace going from BATT+ to an ADC pin with a voltage divider so that we can know when to charge the batteries. The sample is then displayed on a 2.66in E-ink which is also updated every 60 seconds, It displays voltage and ppb.

Bill of Materials

(2 PCBS)

NamePurposeQuantityTotal Cost (USD)LinkDistributor
PassivesCaps,Resistors,Diodes221.00linkJLCPCB
MICROCHIP MCP73831T-2ATI/OTlipo charger22.40linkJLCPCB
AGS10VOC sensor23.20linkJLCPCB
SEEED rp2040MCU211.30linkTME EU
PCBPCBA517.00linkJLCPCB
Waveshare 18321eink display114.28linkTME EU

Photos

image image image image image

Build photos

1000068132 1000068139 1000068131 1000068133

Build Instructions

  • Create PCB jig
  • Apply solder paste using stencil
  • place components
  • add to hotplate to melt solder
  • solder mcu + eink
  • flash firmware by pressing boot and adding the firmware file to the root directory and thats all.

Parts

26
QtyValueFootprintReferences
9BATT+TestPoint:padroundTP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10
2100KResistor_SMD:R_0402_1005MetricR5, R6
24.7KCapacitor_SMD:C_0402_1005MetricR1, R2
24.7uFCapacitor_SMD:C_0603_1608MetricC3, C4
2MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_PadH3, H4
1100nFCapacitor_SMD:C_0402_1005MetricC1
12KResistor_SMD:R_0402_1005MetricR3
1470Resistor_SMD:R_0402_1005MetricR4
1BATT-TestPoint:padroundTP1
1D_Schottky_SmallDiode_SMD:D_SOD-123D2
1LED_SmallLED_SMD:LED_0603_1608MetricD1
1MCP73831T-2ACI_OTlipo:SOT95P280X145-5NU3
1XIAO-RP2040-SMDxiao:XIAO-RP2040-SMDU2
1~Sensor:AGS10U1

Similar boards

  • 4 layers45 × 41 mmOsw, the printed circuit board in 3D

    Osw

    Open-Smartwatch/open-smartwatch-gps

    Hardware design files for the GPS version of the open-smartwatch

    70 parts243GPL-3.0
  • 4 layers38.4 × 128.5 mmPlantpal, the printed circuit board in 3D

    Plantpal

    teapotlaboratories/plantpal

    Your pal in plant care

    121 parts98MIT
  • 2 layers61 × 61 mmCo2-sensor, the printed circuit board in 3D

    Co2-sensor

    blinry/co2-canary

    An open-hardware, ultra-low power CO2 sensor

    57 parts78
  • 4 layers58.4 × 22.9 mmQuickfeather board, the printed circuit board in 3D

    Quickfeather board

    QuickLogic-Corp/quick-feather-dev-board

    100% open source dev kit for EOS S3 MCU+eFPGA SoC supported by fully open source SDK and FPGA Toolchain

    101 parts66CC-BY-SA-4.0
  • 2 layers40.2 × 19.6 mmCompact, the printed circuit board in 3D

    Compact

    jgillick/ThunderPack

    A self-contained microcontroller, battery, and power management system that fits in your pocket.

    59 parts44MIT
  • 4 layers100 × 100 mmV25Panel, the printed circuit board in 3D

    V25Panel

    maholli/SAM32

    Feather-sized SAMD51 with M4 core serving as UART bridge to WROOM ESP32

    211 parts43
  • 2 layers51 × 23.1 mmFeather rak3172, the printed circuit board in 3D

    Feather rak3172

    teapotlaboratories/feather-rak3172

    Teapotlabs Feather RAK3172: Low-cost Low-power LoRaWAN Development Board

    53 parts43MIT
  • 2 layers108 × 95.3 mmBlue Wizard, the printed circuit board in 3D

    Blue Wizard

    wizarddata/Blue-Wizard-Mod

    Bluetooth Controller for the Kinesis Advantage line of keyboards using the BlueMicro firmware

    47 parts38

Questions

How big is the AQM AGS10 PCB?

It measures 99.8 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the AQM AGS10 use?

26 parts, built around the MCP73831T-2ACI/OT-HXY. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the AQM AGS10 KiCad files?

From the lmiez/AGS10-VOC-Monitor repository on GitHub, at the commit this page was made from: the board is KiCad/AQM AGS10.kicad_pcb and its schematic KiCad/AQM AGS10.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the AQM AGS10 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).