

calculator made using super ancient PIC μController.
- Size
- 125 × 185 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 128
- Nets
- 163
- Pads
- 504
- Tracks, vias
- 790, 64
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 13 Dec 2024
- Updated
- 19 Oct 2026
Overview
Proj is an open-source printed circuit board by kpzip, from the kpzip/PICalculator repository on GitHub, published under the EPL-2.0 licence. It is a 2-layer board of 125 × 185 mm with 128 parts on 163 nets, routed with 790 tracks and 64 vias.
It is built around the ISL9111EH50Z-T7A, 74HC238D and SN74LVC1G32DBVR, with the MMBT3904 and WT-1205 among its other parts. Its parts include 46 diodes, 45 switches, 15 resistors, 8 capacitors and 5 ICs. It belongs with the STM32 and PIC boards of this library.
Main components
5ISL9111EH50Z-T7A
SOT-23-6-20℃~+85℃@(TA) 1 1.2MHz 5V Boost Boost Built-in Fixed Yes SOT-23-6 DC-DC Converters ROHSRenesas ElectronicsDC-DC Converters74HC238D
SOP-16SOP-16 Signal Switches, Multiplexers, Decoders ROHSMDDSignal Switches, Multiplexers, DecodersSN74LVC1G32DBVR
SOT-23-5SOT-23-5 Logic Gates ROHSTECH PUBLICLogic GatesMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)WT-1205
插件,D=12mm-20℃~+70℃ 12mm 2.4kHz 4V~6V 50mA 5V 87dB 9.8mm Electromagnetic Passive (Externally Driven) Through-hole 插件,D=12mm Buzzers ROHSSoberton Inc.Buzzers
README
README.mdAward Winning PICalculator
calculator made using super ancient PIC μController.
Past customers have said:
"Fairly risky project that will depend a lot on the development environment. Not clear why 74HC138 will help read the buttons (could probably use SR for same purpose). need to check what exists in terms of development environment "This group chose the hardware as they "wanted a challenge". They are definitely one of the smarter groups in my section so I don't have much doubt that they will get it done.
If you guys do think the hardware is more complex than neccesary, I'm sure they'd be okay with changing out the parts list." "Are these people really experienced or did they find this project online? If the former, will all group members be able to contribute?
PIC16C74 likely does not have Arduino support. "ARM Cortex M4" is vague and any bare chip will likely only come in an SMD package. Both need a special programmer and special compiler setups. Would need to make a custom PCB or buy a dev board.
Why not just do everything in the M4 since it's vastly more powerful than the PIC?" Looks like a very challenging project. I am not sure if all group members can contribute if they decide to go with this idea. I think one or two group members are pretty advanced. I feel like it would be hard to provide help to them since most mentors dont have experience with this microcontroller and it requires a different development environment. Fairly sophisticated, were having issues with some operations outputting the wrong values"
Parts
128| Qty | Value | Footprint | References |
|---|---|---|---|
| 42 | S040S2R0 | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +26 |
| 4 | 100nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3, C4, C5, C6 |
| 4 | 10kΩ | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R11, R12, R13, R14 |
| 4 | 470Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4 |
| 3 | 1kΩ | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5, R7, R9 |
| 3 | 2kΩ | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6, R8, R10 |
| 2 | 22pF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2 |
| 2 | 4.7µF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C7, C8 |
| 2 | Reset | Button_Switch_THT:SW_PUSH_6mm | SW1, SW45 |
| 1 | (/) | Button_Switch_THT:SW_PUSH_6mm | SW26 |
| 1 | + | Button_Switch_THT:SW_PUSH_6mm | SW30 |
| 1 | +/- | Button_Switch_THT:SW_PUSH_6mm | SW5 |
| 1 | - | Button_Switch_THT:SW_PUSH_6mm | SW24 |
| 1 | ./, | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | / | Button_Switch_THT:SW_PUSH_6mm | SW12 |
| 1 | 0 | Button_Switch_THT:SW_PUSH_6mm | SW4 |
| 1 | 1 | Button_Switch_THT:SW_PUSH_6mm | SW21 |
| 1 | 10kΩ | Resistor_THT:R_Array_SIP7 | RN1 |
| 1 | 10kΩ | Potentiometer_SMD:Potentiometer_Bourns_TC33X_Vertical | RV1 |
| 1 | 2 | Button_Switch_THT:SW_PUSH_6mm | SW22 |
| 1 | 200Ω | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R15 |
| 1 | 20MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | 2nd | Button_Switch_THT:SW_PUSH_6mm | SW31 |
| 1 | 2nd | LED_THT:LED_D5.0mm | D43 |
| 1 | 2x AA | Battery:BatteryHolder_MPD_BC2AAPC_2xAA | B1 |
| 1 | 3 | Button_Switch_THT:SW_PUSH_6mm | SW23 |
| 1 | 4 | Button_Switch_THT:SW_PUSH_6mm | SW15 |
| 1 | 4.7µH | Inductor_SMD:L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L1 |
| 1 | 5 | Button_Switch_THT:SW_PUSH_6mm | SW16 |
| 1 | 6 | Button_Switch_THT:SW_PUSH_6mm | SW17 |
| 1 | 7 | Button_Switch_THT:SW_PUSH_6mm | SW9 |
| 1 | 74HC238 | Package_DIP:DIP-16_W7.62mm_Socket_LongPads | U3 |
| 1 | 8 | Button_Switch_THT:SW_PUSH_6mm | SW10 |
| 1 | 9 | Button_Switch_THT:SW_PUSH_6mm | SW11 |
| 1 | Alpha | LED_THT:LED_D5.0mm | D44 |
| 1 | Alpha | Button_Switch_THT:SW_PUSH_6mm | SW25 |
| 1 | Clear | Button_Switch_THT:SW_PUSH_6mm | SW14 |
| 1 | Conn_02x05_Odd_Even | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J1 |
| 1 | Constants | Button_Switch_THT:SW_PUSH_6mm | SW19 |
| 1 | Cos(x)/Cos-1(x) | Button_Switch_THT:SW_PUSH_6mm | SW28 |
| 1 | Deg | LED_THT:LED_D5.0mm | D45 |
| 1 | Deg/Rad | Button_Switch_THT:SW_PUSH_6mm | SW13 |
| 1 | Del | Button_Switch_THT:SW_PUSH_6mm | SW20 |
| 1 | Down | Button_Switch_THT:SW_PUSH_6mm | SW42 |
| 1 | ERM12864-7 | Parts:ERM12864-7 | DS1 |
| 1 | FPU BOOT0 | Button_Switch_THT:SW_PUSH_6mm | SW44 |
| 1 | Graph | Button_Switch_THT:SW_PUSH_6mm | SW37 |
| 1 | ISL9111EH50Z-T7A | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U4 |
| 1 | Left | Button_Switch_THT:SW_PUSH_6mm | SW39 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | PIC16C74 | Package_DIP:DIP-40_W15.24mm_Socket_LongPads | U1 |
| 1 | Power | Button_Switch_THT:SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW43 |
| 1 | Programs | Button_Switch_THT:SW_PUSH_6mm | SW38 |
| 1 | Rad | LED_THT:LED_D5.0mm | D46 |
| 1 | Right | Button_Switch_THT:SW_PUSH_6mm | SW41 |
| 1 | SN74LVC1G32DBVR | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U5 |
| 1 | STM32F401RCTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | Sci/Norm | Button_Switch_THT:SW_PUSH_6mm | SW7 |
| 1 | Sin(x)/Sin-1(x) | Button_Switch_THT:SW_PUSH_6mm | SW27 |
| 1 | Solve/= | Button_Switch_THT:SW_PUSH_6mm | SW6 |
| 1 | Tan(x)/Tan-1(x) | Button_Switch_THT:SW_PUSH_6mm | SW29 |
| 1 | Up | Button_Switch_THT:SW_PUSH_6mm | SW40 |
| 1 | WT-1205 | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | X | Button_Switch_THT:SW_PUSH_6mm | SW18 |
| 1 | X/Matrix | Button_Switch_THT:SW_PUSH_6mm | SW8 |
| 1 | Y/Stats | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | e^x/10^x | Button_Switch_THT:SW_PUSH_6mm | SW36 |
| 1 | log(x)/ln(x) | Button_Switch_THT:SW_PUSH_6mm | SW35 |
| 1 | x^2/√x | Button_Switch_THT:SW_PUSH_6mm | SW34 |
| 1 | x^y/y√x | Button_Switch_THT:SW_PUSH_6mm | SW33 |
| 1 | Γ(x) | Button_Switch_THT:SW_PUSH_6mm | SW32 |
More from kpzip/PICalculator
2- 2 layers125 × 185 mm

- 2 layers125 × 185 mm

Similar boards
- 2 layers76.2 × 165.1 mm

- 4 layers154 × 81 mm

System candidate
bernardopg/ps28-modern-amp
Infinity Primus PS28 amplifier modernization: TPA3255 engineering, validation and safety-gated workflow
269 parts1 - 4 layers155.3 × 50 mm

- 6 layers85.9 × 77.5 mm

Frob2354
tschak909/frob-modern
The Frob, An Apple II Atari 2600 Development System, re-made as an RP2354 based device.
80 parts8 - 4 layers

Service section controller
olin-electric-motorsports/MKV-Boards
Repository for all OEM MKV PCB Projects
226 parts3 - 6 layers65.3 × 65 mm

Fast computer condom
American-Embedded/isolated_reindvstrialize_usb_hub
This repository contains a KiCad project template provided by American Embedded. It is designed to be a starting point for new electronic designs, pre-configured with common settings, layers, and manufacturing outputs.
157 parts1CERN-OHL-P-2.0 - 4 layers275 × 240 mm

- 4 layers50 × 61 mm

Radar
Maritime-Hacking-Village/SAO-2026-Radar
Public repository for the MHV 2026 SAO.
217 parts1CERN-OHL-W-2.0
Questions
How big is the Proj PCB?
It measures 125 × 185 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Proj use?
128 parts, built around the ISL9111EH50Z-T7A, 74HC238D, SN74LVC1G32DBVR and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Proj KiCad files?
From the kpzip/PICalculator repository on GitHub, at the commit this page was made from: the board is pcb/1.2/proj.kicad_pcb and its schematic pcb/1.0/proj.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Proj design in my own project?
Its repository publishes it under the EPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).