Skip to the content
2 layers323.8 × 169.8 mmAegis, the printed circuit board in 3D

unibody CRBKD-compatible PCB and cases.

Size
323.8 × 169.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
110
Nets
82
Pads
573
Tracks, vias
1,424, 76
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
24 Oct 2020
Updated
12 Mar 2021

Overview

Aegis is an open-source printed circuit board by Koumbaya, from the Koumbaya/Aegis repository on GitHub. It is a 2-layer board of 323.8 × 169.8 mm with 110 parts on 82 nets, routed with 1,424 tracks and 76 vias.

It is built around the SK6812MINI-E and TIP120. Its parts include 58 diodes, 1 resistor, 1 IC and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

Aegis

The Aegis is a keyboard that uses the same layout as the crkbd by foostan : https://github.com/foostan/crkbd

pic pic

I wanted certain features like the solenoid so I made a quick PCB that's similar in layout to a crkbd but with only one pro-micro, you can make this PCB if you want a single PCB with underglow and a solenoid, or you can take the crkbd version of the case and slap both halves into this bad boy ! With the brass plate, it weight around 1Kg.

CASE

If you're going for a metal 1,5mm switchplate (which you should, better sound yay !), you'll need to cut :

  • One of every : Aegis_top1, Aegis_top2, Aegis_top3, Aegis_bottom in 3mm acrylic.
  • Three times the Aegis_middle in 3mm acrylic
  • One Aegis_switch_plate in 1,5mm metal of your choosing.

If you want to make everything in acrylic : just do as above minus one Aegis_middle.

You'll need 13 x M3 hex standoffs, >9mm if you have 3 "middle" part, >6 if you have only 2. I've noticed that nylon standoffs are way larger than brass standoffs, so the dxf are designed for nylon standoff (brass ones will turn free) but can be modified. You'll also need 13 x M3x5mm and 13 x M3x8mm screws. The screws heads are hidden underneath the topmost plate, so you'll need something to hold it in place, probably some slim double-sided tape (will update once I've tested). Note : be careful with the top1 and top2 cutouts, I broke mine when peeling the protective plastic sheet. (shoudn't have this problem on the crkbd version I think

3D printed case

This one is pretty much straightforward : print, put PCB inside, close. There is a CRKBD version too.

PCB

The footprints for the diodes are either THT or SMD.

The PCB uses SK6812mini-E for easier soldering, but the footprints are inverted compared to most keyboards : here the underglow LEDs are soldered from under the PCB (facing you when you solder them), instead of being soldered from the top.

top

(soldered from under the PCB, led facing you. beware of the different orientations : the cut tab goes with the dot on the PCB)

I did this because on my previous board some of the LEDs failed after that I had soldered all of the switches, meaning that to change them I had to desolder the switches.

The center LED is soldered like a switch backlight led (from under the PCB, shining towards the top, through the PCB) because it's here to shine on the plate which have a logo cutout (a version without the logo is also available, in which case you'll probably want to just jump the trace for the led from IN to OUT).

inverted

(the cut tab goes on the top/right orientation, led facing back at you)

For the solenoid you'll need 1 TIP120, 1 1N4001 diode, 1 1.1KOhms resistor and 1 5V solenoid. Should look like this solenoid Note : in the v1.1, I've added a hole for the TIP120 because it's too big (by 0.3mm) to fit in the case. In mine I had to sand it down.

Note 2 : I couldn't get the solenoid to work :( with a pro micro I got a reboot, with the elite-c I discovered that the RAW port doesn't exist on it, so I took the VCC, with the same result. I've checked the schematics with some people and it should be good, so I'm putting in on the PCB anyway if someone want to have a crack at it(I've added 2 jumpers to get either VCC or RAW to the solenoid, if you have a pro micro, solder RAW, elite-c : solder VCC. Never both). If you find a solution let me know.

Parts

110
QtyValueFootprintReferences
43D_Smallfootprints:D3_TH_SMDD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +27
42MX-NoLEDMX_Only:MXOnly-1U-NoLEDMX1, MX2, MX10, MX11, MX12, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX21, MX22, MX23 +26
14SK6812MINI-Efootprints:INV-YS-SK6812MINI-LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED9, LED10, LED11, LED12, LED13, LED14, LED15
2Jumper_NO_SmallJumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mmRAW -> SOL, VCC -> SOL
1Connector_Generic_Conn_01x03Connector:FanPinHeader_1x03_P2.54mm_VerticalLEDS1
1Connector_Generic_Conn_01x04Connector:FanPinHeader_1x04_P2.54mm_VerticalOLED
1Device_Jumperfootprints:ResetSWResetSW1
1LOGOcc:ccG***
1Motor_DCfootprints:ResetSWSolenoide1
1ProMicropromicro:ProMicroU1
1R_1kOhmResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR1
1SK6812MINI-Efootprints:YS-SK6812MINI-ELED8
1TIP120Package_TO_SOT_THT:TO-220-3_Horizontal_TabDownQ1

Similar boards

  • 2 layers423.3 × 249.2 mmErgodonk pico, the printed circuit board in 3D

    Ergodonk pico

    JellyTitan/ErgoDonk

    ErgoDox variant using standard SA keycaps, FDM case, and blackpill MCU

    345 parts10MIT
  • 2 layers364.4 × 167.3 mmRedherring, the printed circuit board in 3D

    Redherring

    dcpedit/redherring

    Red Herring Keyboard PCB and case files

    226 parts253CC-BY-4.0
  • 2 layers148.8 × 132.2 mmUsbflashprog, the printed circuit board in 3D

    Usbflashprog

    robsonsmartins/usbflashprog

    A memory device programmer (Flash/EPROM/E2PROM) board and software, connected to PC by USB port.

    125 parts36
  • 2 layers489.6 × 170.7 mmMission control, the printed circuit board in 3D

    Mission control

    dcpedit/mission-control

    Modern replacement PCB for the IBM Model M 122

    286 parts31CC-BY-4.0
  • 2 layers168 × 123 mmV2 - 2, the printed circuit board in 3D

    V2 - 2

    RudgeLab/FluoPi

    Code and teaching materials for UC/BackyardBrains raspberry pi "macro" scope.

    131 parts26
  • 2 layersCatozap, the printed circuit board in 3D

    Catozap

    jones139/catocam

    Uses a custom trained YoloV8 model on a Raspberry Pi to Detect Cats in CCTV images and Unleash a Cat Deterrent

    3 parts18GPL-3.0
  • 2 layers32.5 × 21.2 mmTaptap, the printed circuit board in 3D

    Taptap

    dcpedit/taptap

    TapTap is a solenoid breakout board for those who are interested in adding a solenoid to their existing project. All you need are the following components, and an extra data pin on your microcontroller.

    9 parts13CC-BY-4.0
  • 2 layers57.1 × 102.9 mmSynthwave, the printed circuit board in 3D

    Synthwave

    alexose/synthwave

    An open-source experiment in carbon removal based on the electrochemical pH swing of seawater.

    70 parts10CERN-OHL-P-2.0

Questions

How big is the Aegis PCB?

It measures 323.8 × 169.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Aegis use?

110 parts, built around the SK6812MINI-E and TIP120. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Aegis KiCad files?

From the Koumbaya/Aegis repository on GitHub, at the commit this page was made from: the board is PCB/aegis/aegis.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Aegis design in my own project?

Its repository states no licence, so its author keeps all rights: ask Koumbaya before reusing the design.