

DRC CanTester
- Size
- 60 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 47
- Nets
- 56
- Pads
- 186
- Tracks, vias
- 318, 210
- Pours
- 144
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 May 2026
- Updated
- 3 May 2026
Overview
DRC CanTester is an open-source printed circuit board by kotek-7, from the kotek-7/DRC-CanTester repository on GitHub. It is a 2-layer board of 60 × 60 mm with 47 parts on 56 nets, routed with 318 tracks and 210 vias.
It is built around the ATA6561-GAQW-N, CH340E and RT9080-33GJ5, with the SS2040FL and SSSS213202 among its other parts. Its parts include 14 capacitors, 11 resistors, 5 diodes, 5 switches and 4 ICs. It belongs with the STM32 boards of this library.
Main components
5ATA6561-GAQW-N
SOIC-8-40℃~+150℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHSMicrochip TechnologyCAN TransceiversCH340E
MSOP-10150uA 20mA 2Mbps 3.3V、5V Transceiver USB 2.0 MSOP-10 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersRT9080-33GJ5
TSOT-23-5-40℃~+125℃@(Tj) 1 2uA 3.3V 360mV@(600mA) 42uVrms 5.5V 600mA 75dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRichtek TechVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSS2040FL
SOD-123FLSOD-123FL Schottky Diodes ROHSFUXINSEMISchottky DiodesSSSS213202
SMD-40℃~+85℃ 300mA 5.5mm 6V Rectangular Columnar SMD(SMT) Tab SPDT Surface Mount,Vertical SMD Slide Switches ROHSALPSALPINESlide Switches
Parts
47| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C6, C7, C11, C13, C14 |
| 5 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8, C9, C10 |
| 2 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R10 |
| 2 | RX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | 3V3, D3 |
| 2 | SS2040FL | Diode_SMD:D_SOD-123F | D2, D7 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12 |
| 1 | ACK | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D6 |
| 1 | AQM1602Y-NLW-FBW | lib:AQM1602Y-NLW | LCD1 |
| 1 | ATA6561-GAQW-N | lib:SOIC8_4P9X3P9MC_MCH | U4 |
| 1 | BUS-OFF | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | BUS-OFF_RESET | 0my_project:TS-06104 | SW2 |
| 1 | CAN | Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J1 |
| 1 | CH340E | Package_SO:MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | ERROR | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | LOGO | MyLogo:kuma | G*** |
| 1 | MODE | 0my_project:TS-06104 | SW1 |
| 1 | RESET | 0my_project:TVAF06-A020B-R | SW4 |
| 1 | RT9080-33GJ5 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | SSSS213202 | lib:SSSS213202 | S1 |
| 1 | STLINK | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J2 |
| 1 | STM32F303K8Tx | Package_QFP:LQFP-32_7x7mm_P0.8mm | U2 |
| 1 | TEST | 0my_project:TS-06104 | SW3 |
| 1 | USB_C | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
The 46 most common of 47 parts.
Similar boards
- 2 layers80 × 60 mm

- 2 layers60 × 45 mm

- 2 layers60 × 45 mm

- 2 layers120 × 80 mm

MainBoard v1
shimotoriharuki/2021RoboTrace_Kicad
This repository contains circuit data for line-following robot (UnderBird).
166 parts3GPL-3.0 - 2 layers90 × 70 mm

- 2 layers80 × 60 mm

- 2 layers80 × 60 mm

- 4 layers25.4 × 25.4 mm

SparkFun Qwiic GNSS SAM M8Q
embeddedos-org/eCAD-Hardware-Products
Hardware designs + EE docs + Board datasheets of Multiple products
73 parts8MIT
Questions
How big is the DRC CanTester PCB?
It measures 60 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DRC CanTester use?
47 parts, built around the ATA6561-GAQW-N, CH340E, RT9080-33GJ5 and SS2040FL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DRC CanTester KiCad files?
From the kotek-7/DRC-CanTester repository on GitHub, at the commit this page was made from: the board is DRC-CanTester.kicad_pcb and its schematic AQM1602Y.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DRC CanTester design in my own project?
Its repository states no licence, so its author keeps all rights: ask kotek-7 before reusing the design.