

ESP pwm-4ch V2
ESP8266/ESP32 based board with 4x PWM output channels.
- Size
- 103 × 67.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 38
- Nets
- 49
- Pads
- 127
- Tracks, vias
- 230, 34
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 16 Aug 2022
- Updated
- 19 Apr 2022
Overview
ESP pwm-4ch V2 is an open-source printed circuit board by koson, from the koson/ESP-pwm-4ch repository on GitHub. It is a 2-layer board of 103 × 67.8 mm with 38 parts on 49 nets, routed with 230 tracks and 34 vias.
It is built around the WEMOS D1 MINI, IR4427PBF and L78M05CV, with the IRLB8721PBF among its other parts. Its parts include 8 resistors, 7 capacitors, 5 ICs, 5 connectors and 4 diodes. It belongs with the ESP32, ESP8266 and RISC-V boards of this library.
Main components
4WEMOS D1 MINI
A mini wifi board with 4MB flash based on ESP-8266EX, hardware version 4.0.0.LolinUncategorisedIR4427PBF
PDIP-8-40℃~+150℃ 1.5A 1.5A 100uA 10ns 15ns 2 6V~20V IGBT、MOSFET Low Side PDIP-8 Gate Drivers ROHSInfineon TechnologiesGate DriversL78M05CV
TO-2200℃~+150℃@(Tj) 1 2V 35V 40uV 500mA 5V 62dB@(120Hz) 6mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsIRLB8721PBF
TO-220AB-55℃~+175℃ 1 N-channel 1.077nF 110pF 13nC@4.5V 16mΩ@4.5V 2.35V 30V 360pF 62A 65W N-Channel ±20V TO-220AB MOSFETs ROHSInfineon TechnologiesMOSFETs
README
README.mdESP-pwm-4ch
ESP8266/ESP32 based board with 4x PWM output channels.
This board is designed to be driven by an Olimex ESP32-POE, ESP32-POE-ISO or Wemos D1 Mini modules running Tasmota. If you want to use the ethernet interface present on the Olimex modules you will need to compile your own Tasmota binaries enabling the corresponding features.
The design considers that the board will be mounted on a PCB DIN rail holder offered by the Brazilian manufacturer Metaltex. Check here for details.
Heatsinks are included in the design as I wasn't sure about how much power the MOSFETs would dissipate. The first tests were performed using zero ohm resistors between the drivers and the transistors. A 5A load was applied and the transistor showed no noticeable temperature elevation. In version 2 I replaced the zero ohm resistors for 22 ohm to avoid damages to the drivers, and this setup hasn't yet been tested. Given the very low switching frequency and small loads I suppose the heatsinks are still not needed.
Expect some flicker when driving LEDs with the ESP8266. It gets much more stable when using the hardware PWMs of the ESP32.
There is a preferred version of this board with 8x PWM channels and individual pins for powering groups of two outputs, what enables driving the full 5A per channel. Click here to check it.

Parts
38| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 22R/0,125W/0805 | Tales:R_0805_2012Metric | R4, R5, R6, R7 |
| 4 | Heatsink_16x10x25mm_2xFixationM3 | Tales:Heatsink_16x10x25mm_2xFixationM3 | HS1, HS2, HS3, HS4 |
| 4 | IRLB8721PBF | Tales:TO-220-3_Vertical | Q1, Q2, Q3, Q4 |
| 3 | 0,1uF/50V/0805 | Tales:C_0805_2012Metric | C3, C4, C6 |
| 3 | GREEN/0603 | Tales:LED_0603_1608Metric | D2, D3, D4 |
| 2 | 1uF 35V | Tales:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C5, C7 |
| 2 | IR4427 | Tales:SOIC-8_3.9x4.9mm_P1.27mm | U4, U5 |
| 1 | 0,33uF/35V | Tales:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C2 |
| 1 | 12VDC | Tales:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | 270R/0,125W/0805 | Tales:R_0805_2012Metric | R3 |
| 1 | 2k2/0,125W/0805 | Tales:R_0805_2012Metric | R1 |
| 1 | 47uF/35V/6,3x5,4 | Tales:CP_Elec_6.3x5.4 | C1 |
| 1 | 4k7/0,125W/0805 | Tales:R_0805_2012Metric | R8 |
| 1 | 680R/0,125W/0805 | Tales:R_0805_2012Metric | R2 |
| 1 | L78M05 | Tales:TO-252-2 | U1 |
| 1 | OUT1 | Tales:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J2 |
| 1 | OUT2 | Tales:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J3 |
| 1 | OUT3 | Tales:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | OUT4 | Tales:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J5 |
| 1 | Olimex_ESP32-POE | Tales:Olimex_ESP32-POE_Pads | U3 |
| 1 | SM4007PL/SOD-123 | Tales:D_SOD-123 | D1 |
| 1 | WeMos_D1_mini | Tales:WEMOS_D1_mini_light_pads | U2 |
The 37 most common of 38 parts.
More from koson/ESP-pwm-4ch
1- 2 layers103 × 67.8 mm

Similar boards
- 2 layers113 × 67.8 mm

- 2 layers129 × 66 mm

DC22-PCB1
Le-Dome-RDS/hope-bike
An open source Pedalling Assistant Sytem for 26" wheeled bikes
92 parts8 - 2 layers

- 2 layers81.7 × 45.8 mm

- 2 layers26 × 34.5 mm

Wemos mini external power
dzervas/wemos-mini-external-power
WeMos Mini shield for external power supply (up to 35V)
17 parts - 2 layers83.3 × 26 mm

Moodie analogue controller
mcdonnelldean/moodie
Create LED installations and mood lighting with ease
10 partsMIT - 2 layers160 × 100 mm

- 2 layers53.5 × 67.5 mm

Questions
How big is the ESP pwm-4ch V2 PCB?
It measures 103 × 67.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP pwm-4ch V2 use?
38 parts, built around the WEMOS D1 MINI, IR4427PBF, L78M05CV and IRLB8721PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP pwm-4ch V2 KiCad files?
From the koson/ESP-pwm-4ch repository on GitHub, at the commit this page was made from: the board is V2/ESP-pwm-4ch-V2.kicad_pcb and its schematic V1/ESP-pwm-4ch-V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP pwm-4ch V2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask koson before reusing the design.