

Ftdi probe
FTDI based JTAG and SWD probe with level translators and target power.
- Size
- 43 × 21 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 140
- Nets
- 92
- Pads
- 451
- Tracks, vias
- 1,067, 257
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 8 Jan 2026
- Updated
- 8 Jan 2026
Overview
Ftdi probe is an open-source printed circuit board by korken89, from the korken89/ftdi-probe repository on GitHub. It is a 6-layer board of 43 × 21 mm with 140 parts on 92 nets, routed with 1,067 tracks and 257 vias.
It is built around the SN74LVC1T45DRL, SN74LVC1G3157DRL and MAX40200AUK, with the 93LC46BT-I/OT, AP2112K-3.3 and TLV75801PDBV among its other parts. Its parts include 47 capacitors, 43 resistors, 20 ICs, 5 diodes and 3 connectors. It belongs with the sensors and measurement and interfaces and adapters boards of this library.
Main components
6SN74LVC1T45DRL
SOT-5x3-6-40℃~+85℃ 1 1 1.65V~5.5V 1.65V~5.5V 420Mbps Auto Direction Detection、Power-Off Protection Bidirectional CMOS CMOS Tri-State SOT-5x3-6 Translators, Level Shifters ROHSTexas InstrumentsTranslators / Level ShiftersSN74LVC1G3157DRL
SOT-5x3-40℃~+125℃ 1 1.65V~5.5V 17.3pF 2:1 3.8ns 300ps 340MHz 5.7ns 6Ω SOT-5x3 Analog Switches, Multiplexers ROHSTexas InstrumentsAnalog Switches, MultiplexersMAX40200AUK
SOT23-5Ultra-Tiny Micropower, 1A Ideal Diode with Ultra-Low Voltage DropMaxim Integrated (Analog Devices)Uncategorised93LC46BT-I/OT
SOT-23-6-40℃~+85℃ 1,000,000 cycles 1Kbit 2.5V~5.5V 200 Years 3MHz 6ms SPI Software write protection function、Built-in write enable latch (WEL)、Power-down/Power-up protection circuit SOT-23-6 EEPROM ROHSMicrochip TechnologyEEPROMAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedTLV75801PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 130mV@(500mA) 25uA 30uVrms 500mA 50dB@(1kHz) 550mV~5.5V 6V Adjustable Positive Under Voltage Lockout、Soft Start、Short Circuit Protection、Thermal Shutdown SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
140| Qty | Value | Footprint | References |
|---|---|---|---|
| 34 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C10, C12, C13, C14, C15, C16, C17, C18, C21, C22, C23, C24, C25, C26, C27 +18 |
| 18 | TestPoint_Small | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18 +2 |
| 12 | 10k | Resistor_SMD:R_0402_1005Metric | R3, R5, R6, R8, R18, R19, R22, R23, R24, R25, R26, R35 |
| 10 | 4.7u | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C8, C19, C20, C33, C34, C46, C47 |
| 10 | SN74LVC1T45DRL | Package_TO_SOT_SMD:SOT-563 | U9, U10, U11, U12, U13, U14, U15, U16, U17, U18 |
| 9 | 100 | Resistor_SMD:R_0402_1005Metric | R9, R10, R11, R12, R13, R14, R15, R16, R17 |
| 9 | 330k | Resistor_SMD:R_0402_1005Metric | R27, R28, R29, R30, R31, R32, R33, R34, R37 |
| 4 | 2.2k | Resistor_SMD:R_0402_1005Metric | R7, R20, R21, R36 |
| 3 | 600R | Resistor_SMD:R_0402_1005Metric | FB1, FB2, FB3 |
| 3 | D5V0M1U2S9-7 | Diode_SMD:D_SOD-923 | D2, D3, D4 |
| 3 | SN74LVC1G3157DRL | Package_TO_SOT_SMD:SOT-563 | U4, U5, U6 |
| 2 | 12p | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | MAX40200AUK | Package_TO_SOT_SMD:SOT-23-5 | U7, U8 |
| 1 | 0 | Resistor_SMD:R_0402_1005Metric | R43 |
| 1 | 12 MHz | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | 12k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 147k | Resistor_SMD:R_0402_1005Metric | R39 |
| 1 | 191k | Resistor_SMD:R_0402_1005Metric | R38 |
| 1 | 22u | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 41.2k | Resistor_SMD:R_0402_1005Metric | R42 |
| 1 | 66.5k | Resistor_SMD:R_0402_1005Metric | R41 |
| 1 | 93.1k | Resistor_SMD:R_0402_1005Metric | R40 |
| 1 | 93LC46BT-I/OT | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | FT4232HQ | Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP4.35x4.35mm | U3 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D5 |
| 1 | NUF8401MNT4G | dfn:DFN-16-1EP_1.6x4mm_P0.5mm | U19 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | TLV75801PDBV | Package_TO_SOT_SMD:SOT-23-5 | U20 |
| 1 | USB_C_Receptacle_USB2.0_14P | connectors:USB_C_Receptacle_USB4105 | J1 |
Similar boards
- 2 layers89.2 × 62.4 mm

- 4 layers52.8 × 22.9 mm

- 4 layers136.7 × 52.7 mm

- 4 layers72 × 44 mm

Picflash board
nthclrd/picflash
Programmeur PIC open source en Rust : remplace MPLAB IPE/XC8 pour les PIC16, pilote les PICkit 4/5/Basic ou une carte RP2040 maison (KiCad)
115 parts1MIT - 6 layers141.7 × 105.1 mm

NuBoard
wickerwaka/nuBoard
Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.
330 parts1 - 2 layers25 × 60.9 mm

Pico Usb
pedro00100/usb-pico-ducky
An advanced(Bad Usb - Rubber Ducky), high-performance CircuitPython DuckyScript engine compatible with the Raspberry Pi Pico and Pico 2.
40 parts1GPL-3.0 - 2 layers82.5 × 49 mm

Obd2dash
EthanPope07/obd2dash
An ESP32-S3 CAN-to-BLE bridge for an iPad vehicle dashboard. The firmware discovers each ECU's supported current-data PIDs and forwards complete raw responses through a versioned BLE GATT stream.
22 parts - 4 layers100 × 100 mm

Questions
How big is the Ftdi probe PCB?
It measures 43 × 21 mm and has 6 copper layers, 1.6 mm thick.
What parts does the Ftdi probe use?
140 parts, built around the SN74LVC1T45DRL, SN74LVC1G3157DRL, MAX40200AUK and 93LC46BT-I/OT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ftdi probe KiCad files?
From the korken89/ftdi-probe repository on GitHub, at the commit this page was made from: the board is ftdi-probe.kicad_pcb and its schematic ftdi-probe.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ftdi probe design in my own project?
Its repository states no licence, so its author keeps all rights: ask korken89 before reusing the design.