

- Size
- 95.5 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 46
- Pads
- 275
- Tracks, vias
- 1,405, 405
- Pours
- 30
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 15 Jan 2018
- Updated
- 21 Jun 2018
Overview
Imu is an open-source printed circuit board by komori-t, from the komori-t/Tupac2018 repository on GitHub. It is a 2-layer board of 95.5 × 50 mm with 55 parts on 46 nets, routed with 1,405 tracks and 405 vias.
It is built around the LPC11U35FHI33/501, PCA9515AD and OKL-T/6-W12N-C. Its parts include 18 capacitors, 17 resistors, 7 connectors, 6 ICs and 2 transistors. It belongs with the sensors and measurement boards and the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
3LPC11U35FHI33/501
HVQFN-33(5x5)1.8V~3.6V 10bit 26 50MHz 64KB ARM Cortex-M0 HVQFN-33(5x5) Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)PCA9515AD
SO-8-40℃~+85℃ 1 2 2.3V~3.6V 68ns@3.3V,50pF 6mA Bidirectional Open-drain Power-off isolation、Output enable SO-8 Buffers, Drivers, Receivers, Transceivers ROHSNXP SemiconductorsBuffers, Drivers, Receivers, TransceiversOKL-T/6-W12N-C
SMD,12.2x12.2mm1 12.2mm 12.2mm 20mVp-p 300uF 30W 4.5V~14V 591mV~5.5V 600kHz 6A 7.2mm 93% Short Circuit Protection、Over Current Protection、Under Voltage Protection、Over-temperature protection、Automatic fault recovery、Power-on timing control SMD,12.2x12.2mm DC-DC Power Modules ROHSMurataIsolated Power Modules
README
README.mdTupac2018
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0.1u | Capacitors_SMD:C_0603 | C1, C2, C4, C5, C7, C12, C13, C16, C18 |
| 4 | 18p | Capacitors_SMD:C_0603 | C8, C9, C10, C11 |
| 4 | 4.7k | Resistors_SMD:R_0603 | R5, R6, R16, R17 |
| 3 | 10k | Resistors_SMD:R_0603 | R7, R12, R13 |
| 2 | 1.0u | Capacitors_SMD:C_0603 | C15, C17 |
| 2 | 100k | Resistors_SMD:R_0603 | R1, R2 |
| 2 | 33 | Resistors_SMD:R_0603 | R8, R9 |
| 2 | GS2 | Connectors:GS2 | J6, J7 |
| 2 | PCA9515A | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U3, U4 |
| 1 | 0.01u | Capacitors_SMD:C_0603 | C14 |
| 1 | 1.5k | Resistors_SMD:R_0603 | R10 |
| 1 | 10 | Resistors_SMD:R_0603 | R15 |
| 1 | 10u | Capacitors_SMD:C_0805 | C6 |
| 1 | 12M | Crystals:Crystal_SMD_SeikoEpson_FA238V-4pin_3.2x2.5mm | Y1 |
| 1 | 1k | Resistors_SMD:R_0603 | R11 |
| 1 | 22u | Capacitors_SMD:C_0805 | C3 |
| 1 | 240k | Resistors_SMD:R_0603 | R3 |
| 1 | 330 | Resistors_SMD:R_0603 | R14 |
| 1 | 75k | Resistors_SMD:R_0603 | R4 |
| 1 | AQM1602 | AQM0802:AQM1602 | U5 |
| 1 | Batt | Connectors_JST:JST_EH_S02B-EH_02x2.50mm_Angled | J1 |
| 1 | Debug | Connectors_JST:JST_PH_S5B-PH-K_05x2.00mm_Angled | J2 |
| 1 | Jetson | Socket_Strips:Socket_Strip_Straight_2x10_Pitch2.54mm_SMD | J5 |
| 1 | Jetson_USB | Connectors_JST:JST_PH_S4B-PH-K_04x2.00mm_Angled | J3 |
| 1 | LPC11U35FHI33/501 | Housings_DFN_QFN:QFN-32-1EP_5x5mm_Pitch0.5mm | U2 |
| 1 | MIL-14 | Pin_Headers:Pin_Header_Straight_2x07_Pitch2.54mm | J4 |
| 1 | MPU6500 | Housings_DFN_QFN:QFN-24-1EP_3x3mm_Pitch0.4mm | U6 |
| 1 | OKL-T/6-W12N-C | OKL-T_6-W12N-C:OKL-T_6-W12N-C | U1 |
| 1 | Q_NMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q2 |
| 1 | Q_PMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q1 |
The 51 most common of 55 parts.
More from komori-t/Tupac2018
1- 2 layers46.5 × 34 mm

Similar boards
- 2 layers39 × 20 mm

SODA
ExploreEmbedded/SODA_SWD-Opensource-Debug-Adapter
SODA is CMSIS Debug Adapter based on LPC11u35
37 parts3CC0-1.0 - 4 layers100 × 100 mm

- 2 layers330.5 × 115.6 mm

- 2 layers32 × 32 mm

Efm32wg
dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere
61 parts14Apache-2.0 - 2 layers72 × 47 mm

- 2 layers70 × 76 mm

- 2 layers84 × 114 mm

- 2 layers95.9 × 83.8 mm

Questions
How big is the Imu PCB?
It measures 95.5 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Imu use?
55 parts, built around the LPC11U35FHI33/501, PCA9515AD and OKL-T/6-W12N-C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Imu KiCad files?
From the komori-t/Tupac2018 repository on GitHub, at the commit this page was made from: the board is circuit/imu/imu.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Imu design in my own project?
Its repository states no licence, so its author keeps all rights: ask komori-t before reusing the design.