
Piweather
pluggee/piweather
raspberry pi based system for weather monitoring and automation

An inexpensive motion tracking system
IMUTracker is an open-source printed circuit board by komori-t, from the komori-t/QUIKS repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 30 × 30 mm with 32 parts on 25 nets, routed with 310 tracks and 51 vias.
It is built around the LPC802M001JDH16, THVD1500D and FT234XD-R, with the ICM-20948 and MIC5504-1.8YM5-TR among its other parts. Its parts include 12 capacitors, 6 connectors, 5 ICs, 4 resistors and 1 diode. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
QUIKS unifies inexpensive kinetic sensors
QUIKS is an inexpensive motion tracking system.
It is consists of one terminal node and multiple sensor nodes.
Each node has a sensor and the terminal node bridges PC and them.

QUIKS is designed to construct motion tracking system at low cost.
New node can be added by just connecting to RS485 bus.
It is easy to develop new kind of node to extend the system.
More nodes you connect, more data you get.
So you can omit any nodes to reduce costs, areas, times, etc.
If you do not need to track the lower half of your body, you can only upper half nodes for example.
The IMUTracker is a kind of node that captures rotation of one bone.
It has IMU sensor ICM20948 controlled by a tiny microcontroller LPC802.
USB terminal node is a kind of terminal node that communicates with PC through USB.
It acts as virtual serial port and bridges USB and RS485 bus.
IMUTracker and USB terminal node shares the same design of circuit to reduce manufacturing costs.
Wireless terminal node is a kind of teminal node that communicates with PC wirelessly (maybe in 900 MHz band).
If the position of one bone (typically waist) can be detected, it is possible to move around in virtual world.
A technical memo (in the form of paper) of IMUTracker can be found here.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1u | Capacitors_SMD:C_0603 | C3, C5, C7, C8, C9, C12 |
| 2 | 0.01u | Capacitors_SMD:C_0603 | C2, C6 |
| 2 | 1u | Capacitors_SMD:C_0603 | C1, C4 |
| 2 | 27 | Resistors_SMD:R_0603 | R3, R4 |
| 2 | 47p | Capacitors_SMD:C_0603 | C10, C11 |
| 2 | Conn_01x04 | JST_PA:JST_PA_04_Angled | J5, J6 |
| 1 | 120 | Resistors_SMD:R_0603 | R2 |
| 1 | 2k | Resistors_SMD:R_0603 | R1 |
| 1 | FT234XD | Housings_DFN_QFN:DFN-12-1EP_3x3mm_Pitch0.45mm | U3 |
| 1 | GND | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J3 |
| 1 | ICM-20948 | ICM20948:ICM20948 | U5 |
| 1 | LED | LEDs:LED_0603 | D1 |
| 1 | LPC802M001JDH16 | Housings_SSOP:TSSOP-16_4.4x5mm_Pitch0.65mm | U2 |
| 1 | MIC5504-1.8YM5-TR | TO_SOT_Packages_SMD:SOT-23-5 | U1 |
| 1 | SWCLK | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J1 |
| 1 | SWDIO | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J2 |
| 1 | THVD1500 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U4 |
| 1 | USB_OTG | ZX62-B-5PA:ZX62-B-5PA | J4 |
The 28 most common of 32 parts.

pluggee/piweather
raspberry pi based system for weather monitoring and automation

jonghee-son/USB-to-RS485-Converter-Small
USB to RS485 Converter made with SMD parts


ThunderFly-aerospace/TFASPDIMU02
I²C bus differential pressure sensor with IMU and Magnetometer.


Case-Rocket-Team/PayloadPrototypeBoard2021
Prototype Payload Board for the 2021 ESRA Payload using Parafoil Guidance. KiCad Project

ThunderFly-aerospace/TFASPDIMU01
SPI or I²C differential pressure sensor and IMU unit.

mlab-modules/DATALOGGER02
Arduino based data logger with LoRa IoT interface.
It measures 30 × 30 mm and has 2 copper layers, 1.6 mm thick.
32 parts, built around the LPC802M001JDH16, THVD1500D, FT234XD-R and ICM-20948. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the komori-t/QUIKS repository on GitHub, at the commit this page was made from: the board is Hardware/IMUTracker/Circuit/IMUTracker.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).