
DI Lambda UNO top
koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

Schematics for AVR-based DI-Lambda DITOS and UNO v1
DI Lambda UNO bottom is an open-source printed circuit board by koi-science, from the koi-science/DI-Lambda-schematics-avr repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 38.2 × 128 mm with 39 parts on 67 nets, routed with 333 tracks and 10 vias.
It is built around the AP3015, USBLC6-2SC6 and AO3400, with the AO3401 and SS14 among its other parts. Its parts include 12 connectors, 6 capacitors, 6 resistors, 4 inductors and 3 ICs.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 4.7uF 6.3v | Capacitor_SMD:C_0603_1608Metric | C101, C102, C103, C105 |
| 4 | Conn_02x04_Odd_Even | Board_grooves:Pocket_1.6mm_10mm_no_cap_8pads_short_vias | J103, J104, J110, J111 |
| 3 | 4.75k | Resistor_SMD:R_0603_1608Metric | R103, R104, R106 |
| 3 | FB | Inductor_SMD:L_0603_1608Metric | L101, L102, L103 |
| 2 | 1uF 16v | Capacitor_SMD:C_0603_1608Metric | C104, C106 |
| 2 | 22R | Resistor_SMD:R_0603_1608Metric | R101, R102 |
| 2 | CONN_01X06 | Spring-contact-connector-2:Spring-contact-connector-2.5x6 | J102, J112 |
| 2 | Conn_02x02_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_Vertical_SMD | J105, J106 |
| 2 | Conn_02x03_Odd_Even | Board_grooves:Pocket_1.6mm_10mm_2cap_6pads_short_vias | J108, J109 |
| 2 | Mounting_Hole | DI-Lambda-module-tabs:Slot_pinhole | MK102, MK103 |
| 1 | 0.2A | Fuse:Fuse_1206_3216Metric | F101 |
| 1 | 3.3v LDO | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U102 |
| 1 | 42.2k | Resistor_SMD:R_0603_1608Metric | R105 |
| 1 | 6.8uH | Inductor_SMD:L_Taiyo-Yuden_NR-40xx | L104 |
| 1 | AO3400 | Package_TO_SOT_SMD:SOT-23 | Q102 |
| 1 | AO3401 | Package_TO_SOT_SMD:SOT-23 | Q101 |
| 1 | AP3015 | Package_TO_SOT_SMD:SOT-23-5 | U103 |
| 1 | Conn_01x01 | Cuvette-holder:Cuvette-holder | J107 |
| 1 | Mounting_Hole | DI-Lambda-module-tabs:Slot_sensor | MK104 |
| 1 | Mounting_Hole | DI-Lambda-module-tabs:Slot_LED | MK101 |
| 1 | SS14 | Diode_SMD:D_SMA | D101 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U101 |
| 1 | USB_OTG | Connector_USB:USB_Micro-B_Molex-105017-0001 | J101 |

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1

koi-science/DI-Lambda-schematics-avr
Schematics for AVR-based DI-Lambda DITOS and UNO v1


tomasmcguinness/matter-esp32-mbus-adapter
An ESP32-C6 adapter board for wired M-Bus (EN 13757) meters, with firmware examples that expose meter readings to a Matter fabric over Thread.


Cuprum77/LCD_Driver
FPGA based LCD driver for cheap ST7701S displays


eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32

damnitzhemanth-oss/Flight_Controller
Custom STM based flightcontroller designed from scratch.

sudomesh/disaster-radio
A (paused) work-in-progress long-range, low-bandwidth wireless disaster recovery mesh network powered by the sun.
It measures 38.2 × 128 mm and has 2 copper layers, 1.6 mm thick.
39 parts, built around the AP3015, USBLC6-2SC6, AO3400 and AO3401. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the koi-science/DI-Lambda-schematics-avr repository on GitHub, at the commit this page was made from: the board is DI-Lambda-UNO/DI-Lambda-UNO-bottom/DI-Lambda-UNO-bottom.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).