4 layers123.8 × 362.3 mm
4 layers66.3 × 60.9 mm
With esc basic v1
karmanyaahm/fidget- Size
- 66.3 × 60.9 mm
- Copper layers
- 4
- Thickness
- 0.8 mm
- Parts
- 70
- Nets
- 59
- Pads
- 228
- Tracks, vias
- 1,872, 105
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 5 Aug 2024
- Updated
- 5 Aug 2024
Overview
With esc basic v1 is an open-source printed circuit board by karmanyaahm, from the karmanyaahm/fidget repository on GitHub. It is a 4-layer board of 66.3 × 60.9 mm with 70 parts on 59 nets, routed with 1,872 tracks and 105 vias.
It is built around the ATTINY3217-MF, STSPIN233 and TLC59282DBQ, with the OV-7604-C7 among its other parts. Its parts include 19 resistors, 18 diodes, 9 capacitors, 7 ICs and 1 connector. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
4
ATTINY3217-MF
WQFN-24-EP(4x4)-40℃~+125℃ 16MHz 2.7V~5.5V 22 256Byte 2KB 32KB 8 Bit AVR Built-in FLASH WQFN-24-EP(4x4) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontroller Units (MCUs/MPUs/SOCs)
STSPIN233
QFN-16-EP(3x3)-40℃~+150℃ 1.8V~10V 3 400mΩ 80nA Three Phase QFN-16-EP(3x3) Brushless DC (BLDC) Motor Driver ROHSSTMicroelectronicsGate Drivers
TLC59282DBQ
SSOP-24-150mil-40℃~+85℃ 16 17V 2% 35MHz 3V~5.5V 45mA Built-in SSOP-24-150mil LED Drivers ROHSTexas InstrumentsLED DriversOV-7604-C7
SMD-4P,1.5x3.2x1.00PSMD-4P,1.5x3.2x1.00P New Arrivals ROHSMicro CrystalUncategorised
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 5k1 | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25, R26, R27 +1 |
| 16 | RLED | LED_SMD:LED_0402_1005Metric | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16 |
| 4 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1, NT2, NT3, NT4 |
| 4 | TestPoint | TestPoint:TestPoint_THTPad_1.5x1.5mm_Drill0.7mm | TP3, TP4, TP5, TP6 |
| 3 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C4, C6 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C2, C8, C9 |
| 3 | AH1806-W??? | Package_TO_SOT_SMD:SC-59 | U4, U6, U7 |
| 3 | Battery_Cell | 0fidgetlibrary:BAT_BK-5009 | BT1, BT2, BT3 |
| 2 | TestPoint_Probe | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | TP1, TP2 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 1n | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 22u | Capacitor_SMD:CP_Elec_4x5.4 | C3 |
| 1 | 25k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | ATtiny3217-M | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 1 | D_TVS | Diode_SMD:D_0603_1608Metric | D17 |
| 1 | LED | LED_SMD:LED_0402_1005Metric | D19 |
| 1 | MountingHole_Pad | 0fidgetlibrary:MountingHole_2.2mm_M2_Pad_thin | H1 |
| 1 | OV-7604-C7 | 0fidgetlibrary:OSC_OV-7604-C7-32.768KHZ-20PPM-TB-QA | X1 |
| 1 | Prog | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J1 |
| 1 | STSPIN233 | Package_DFN_QFN:VQFN-16-1EP_3x3mm_P0.5mm_EP1.8x1.8mm | U3 |
| 1 | SW_SPST | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | TLC59282 | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.15x2.15mm | U5 |
| 1 | TP4101 | Package_TO_SOT_SMD:SOT-23-6 | U8 |
Similar boards
- 4 layers160 × 160 mm
DAQCard2015
frmeier/VFPIX-telescope-PCB
Repository for DTB used in the PSI pixel telescope and VFPIX project
232 parts - 2 layers316 × 222 mm
- 2 layers69.3 × 300 mm
Pcb tile game tile panelized
bytesizedengineering/PCB-tile-based-game
🧰 What You Need - Adafruit UPDI Friend - Arduino IDE - ATtiny3217 board - USB-C cable 1. Install MegaTinyCore 2. Select the Board 3. Connect the UPDI Friend 4. Select the Serial Port 5. Upload Code
198 parts4GPL-3.0 - 2 layers53.3 × 83.3 mm
PCBbuscard
Lmello1/ProtoPCB
Business card PCB and pocket Attiny3227 and LED matrix playground. Powered by a CR2032 battery
291 parts3 - 4 layers
Power module
FETfox/Li-Ion_Power_Module
A PCB that can protect,charge, and regulate a Li Ion battery to power MCU powered projects.
144 partsCC0-1.0 - 2 layers58.4 × 22.6 mm
- 2 layers43.2 × 17.8 mm
ATTinyX17
vul-os/sirboard
Open hardware: 107 KiCad PCB designs — SMD-to-THT breakout adapters, ATTiny/ATMega/ESP development boards, and a 39-part sensor line on a common JST-SH connector.
33 parts56Apache-2.0
Questions
How big is the With esc basic v1 PCB?
It measures 66.3 × 60.9 mm and has 4 copper layers, 0.8 mm thick.
What parts does the With esc basic v1 use?
70 parts, built around the ATTINY3217-MF, STSPIN233, TLC59282DBQ and OV-7604-C7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the With esc basic v1 KiCad files?
From the karmanyaahm/fidget repository on GitHub, at the commit this page was made from: the board is with_esc_basic_v1/with_esc_basic_v1.kicad_pcb and its schematic pcb_motor_prototype_1/pcb_motor_prototype_1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the With esc basic v1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask karmanyaahm before reusing the design.