

DropInTapPT2399
- Size
- 10.1 × 20.3 mm
- Copper layers
- 4
- Thickness
- 1 mm
- Parts
- 26
- Nets
- 38
- Pads
- 115
- Tracks, vias
- 211, 29
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 5 Jul 2025
- Updated
- 11 May 2026
Overview
DropInTapPT2399 is an open-source printed circuit board by kanengomibako, from the kanengomibako/Modules repository on GitHub, published under the Unlicense licence. It is a 4-layer board of 10.1 × 20.3 mm with 26 parts on 38 nets, routed with 211 tracks and 29 vias.
It is built around the CH32V003F4U6, PT2399 and LMV321, with the MMBT3904 among its other parts. Its parts include 9 resistors, 8 connectors, 4 capacitors, 3 ICs and 1 transistor. It belongs with the RISC-V boards of this library.
Main components
4CH32V003F4U6
QFN-20(3X3)16KB 18 48MHz Others QFN-20(3X3) Microcontrollers (MCU/MPU/SOC) ROHSWCH (Nanjing Qinheng Microelectronics)Microcontrollers (MCU/MPU/SOC)PT2399
DIP-16Processor DIP-16 Audio Interface ICs ROHSPTCAudio Interface ICsLMV321
SOT-23-5L-2.75V~-1.25V、1.25V~2.75V 0℃~+70℃ 1 10pA 10pA 1MHz 2.1V~5.5V 20mA 20nV/√Hz@10kHz 520V/ms 60uA 70dB 800uV Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Operational Amplifier ROHSJiangsu Changjing Electronics Technology (CJ)Operational AmplifierMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
10VBlocker/README.md10V Blocker

10V以上の電圧が入力されると、電源供給を遮断するモジュールです。
配線方法
- IN → 電源入力 +
- 上側中央のパッド → 電源入出力 -(グラウンド)
- OUT → 電源出力 +
基板下側のパッドはどこにも接続されていません。マル信無線電機 DCジャック MJ-40Aに直付けする場合、電池の接続が可能です。
注意事項
- 新品の電池は電圧が10V以上の場合があり、本モジュールにより電源が遮断される可能性があります。
- 電源の遮断が不十分となる場合があるため、消費電流0.1mA未満の機器には使用しないでください。
資料
| 主な仕様 | |
|---|---|
| 最大入力電圧 | 30V |
| 遮断電圧 | 10.0V ~ 10.3V |
| 直列抵抗 | 0.04Ω |
| 消費電流 | 0.7mA |
| 最大出力電流 | 1A |
| 必要出力電流 | 0.1mA以上 |
| 外形寸法 | 幅 12 mm × 奥行 10 mm × 高さ 2.5 mm |
| 質量 | 約 0.4 g |
Parts
26| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C5 |
| 4 | 33k | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3 |
| 2 | GND | myFoot:my_WirePad_0-8mmDrill | J4, J99 |
| 1 | 1.5k | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 47k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 5V | myFoot:my_WirePad_0-8mmDrill | J3 |
| 1 | CH32V003F4U6 | myFoot:QFN-20-1EP_3x3mm_rotate | U1 |
| 1 | DTime | myFoot:my_WirePad_0-8mmDrill | J6 |
| 1 | LED | myFoot:my_WirePad_0-8mmDrill | J1 |
| 1 | LMV321 | myFoot:my_SOT-23-5_rotate | U2 |
| 1 | MMBT3904 | myFoot:SOT-23_rotate | Q1 |
| 1 | PT2399 | myFoot:my_SOP-16_SmallPad | U3 |
| 1 | PT2399_CONN | myFoot:my_DIP-16_ex | J7 |
| 1 | SWIO | myFoot:my_WirePad_1mmDrill | TP1 |
| 1 | TapDiv | myFoot:my_WirePad_0-8mmDrill | J5 |
| 1 | TapSw | myFoot:my_WirePad_0-8mmDrill | J2 |
More from kanengomibako/Modules
7- 2 layers45 × 35 mm

- 2 layers48.9 × 26.7 mm

- 2 layers35 × 24.5 mm

- 4 layers24.5 × 24.5 mm

- 2 layers17.9 × 15 mm

- 2 layers25.5 × 11 mm

- 2 layers12 × 9.5 mm

Similar boards
- 4 layers27.9 × 108 mm

- 2 layers127 × 128.5 mm

Dolphins
apaleslimghost/synths
schematics, PCBs, designs and code for Pale Slim Ghost Synthesisers hardware
208 parts5 - 2 layers19 × 107.9 mm

- 2 layers88.9 × 38.1 mm

- 2 layers53.5 × 101.8 mm

Sony scopeman
lucysrausch/sony-scopeman
Hardware Design files of a replacement mainboard for the Sony Watchman FD-10. This turns it into a bluetooth and WiFi-enabled vector display.
135 parts69 - 2 layers65 × 100 mm

JBclone soldering station
Minu-IU3IRR/JBclone-soldering-station
Multi channel DIY soldering station with JBC tip support
55 parts13 - 4 layers102.1 × 73.8 mm

Tape Emulator
SteveLRojas/MC-10_Tape_Emulator
Unified HW and SW repository for the TRS-80 MC-10 tape emulator project.
95 parts2 - 4 layers116.5 × 84.4 mm

Questions
How big is the DropInTapPT2399 PCB?
It measures 10.1 × 20.3 mm and has 4 copper layers, 1 mm thick.
What parts does the DropInTapPT2399 use?
26 parts, built around the CH32V003F4U6, PT2399, LMV321 and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DropInTapPT2399 KiCad files?
From the kanengomibako/Modules repository on GitHub, at the commit this page was made from: the board is DropInTapPT2399/KiCad/DropInTapPT2399.kicad_pcb and its schematic 10VBlocker/10VBlocker_RevB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DropInTapPT2399 design in my own project?
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).