Skip to the content
2 layers73 × 100 mmDs1, the printed circuit board in 3D
Size
73 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
88
Nets
54
Pads
216
Tracks, vias
526, 64
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
4 Jul 2025
Updated
15 Jun 2026

Overview

Ds1 is an open-source printed circuit board by kanengomibako, from the kanengomibako/EffectsPedals repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 73 × 100 mm with 88 parts on 54 nets, routed with 526 tracks and 64 vias.

It is built around the OPA1679ID, HEF4027BT and 1N4148W, with the 2SK208-GR and GS1010FL among its other parts. Its parts include 29 resistors, 25 capacitors, 9 diodes, 4 transistors and 3 connectors.

Main components

5

README

PedalMeetingHeadphoneAmp/README.md

Pedal Meeting Headphone Amp

Pedal Meeting Headphone Amp Picture

エフェクター展示会の試奏ブースでのコミュニケーションを円滑にするために設計されたヘッドフォンアンプです。ギター/ベースの音と会話用のマイク音声をミックスし、ヘッドフォンで聴くことができます。試奏者と出展者が音を共有できると共に、ヘッドフォンを外さずに会話することが可能となります。

※ 電源は、DC9V(センターマイナス)出力のACアダプターで、0.3A以上の電流出力が可能なものを使用してください。

■ 入力

それぞれ独立したゲイン調整を備えています。ゲインを上げ過ぎるとハウリングが起こることがありますのでご注意ください。

  • INST

    楽器側の音声出力を接続します。アンプ・キャビネットシミュレータからの接続を想定しています。ゲインは基本的に中央で固定し、微調整として使用してください。

  • MIC1/MIC2

    外部マイクを接続します。48Vファンタム電源が必要なマイクには対応していません。

  • MIC3

    本体トップ面にあるマイクです。外部マイクがない場合でも、会話を拾うことが可能です。

■ 出力

楽器の音とマイクの音をそれぞれ出力ボリュームで調整できます。

  • PHONES A/B

    試奏者用、出展者用のヘッドフォンを接続します。

  • LINE A/B

    外部録音機器を接続できます。

■ スイッチ

  • MIC ON/OFF

    すべてのマイク入力を一括でミュートします。マイクが楽器の生音を拾うため、会話時以外はマイクをOFF(LED消灯)にすることをお勧めします。

  • MIC 5V

    プラグインパワー方式のコンデンサーマイク(BEHRINGER BC LAV 等)を使用する際にONにします。ダイナミックマイク接続時はOFFにします。48Vファンタム電源が必要なマイクには対応していません。

■ 資料

■ 主な仕様
入力インピーダンス47kΩ(INST)
10kΩ(MIC)
出力インピーダンス1 kΩ(LINE)
10Ω(PHONES)
最大出力レベル2.5 Vrms(LINE)
50 mW + 50 mW, 32Ω(PHONES)
コントロールMIC ON/OFFスイッチ MIC 5Vスイッチ GAINつまみ × 4 VOLつまみ × 4
インジケーター赤色LED(電源ON)
青色LED(マイクON)
接続端子INST MIC1/2 PHONES A/B LINE A/B 電源入力端子
消費電流40 mA(無信号時)
300 mA(最大出力時)
外形寸法幅 100 mm × 奥行 130 mm × 高さ 57 mm
質量550 g

Parts

88
QtyValueFootprintReferences
71MmyFoot:my_R_1608(0603)_HandSolderingR2, R4, R18, R19, R23, R25, R27
60.1umyFoot:my_C_1608(0603)_HandSolderingC18, C19, C21, C22, C24, C25
6100kmyFoot:my_R_1608(0603)_HandSolderingR3, R5, R9, R12, R21, R24
61N4148WmyFoot:my_D_SOD-123D1, D2, D3, D4, D5, D8
410kmyFoot:my_R_1608(0603)_HandSolderingR7, R17, R28, R29
3100nmyFoot:my_C_3225(1210)_HandSolderingC1, C13, C14
32.2kmyFoot:my_R_1608(0603)_HandSolderingR13, R15, R26
32SK208-GRmyFoot:my_SOT-23Q1, Q3, Q4
3470nmyFoot:my_C_Rect2_P5.00mmC2, C8, C10
2100kBmyFoot:my_Pot_PTV09A-4RV1, RV3
210nmyFoot:my_C_1608(0603)_HandSolderingC11, C16
21kmyFoot:my_R_2012(0805)_HandSolderingR1, R20
222nmyFoot:my_C_2012(0805)_HandSolderingC6, C12
247nmyFoot:my_C_3225(1210)_HandSolderingC3, C7
26.8kmyFoot:my_R_1608(0603)_HandSolderingR14, R16
1100pmyFoot:my_C_1608(0603)_HandSolderingC9
1100umyFoot:my_C_Elec_6.3C20
110umyFoot:my_C_Elec_5C15
120kBmyFoot:my_Pot_PTV09A-4RV2
1220RmyFoot:my_R_2012(0805)_HandSolderingR22
1220pmyFoot:my_C_1608(0603)_HandSolderingC5
122RmyFoot:my_R_2012(0805)_HandSolderingR8
122pmyFoot:my_C_1608(0603)_HandSolderingC4
12SC3324-GRmyFoot:my_SOT-23Q2
14.7kmyFoot:my_R_1608(0603)_HandSolderingR11
1470kmyFoot:my_R_1608(0603)_HandSolderingR6
1470pmyFoot:my_C_1608(0603)_HandSolderingC17
147kmyFoot:my_R_1608(0603)_HandSolderingR10
147umyFoot:my_C_3225(1210)_HandSolderingC23
15.1V_ZenermyFoot:my_D_SOD-123D6
1DC_JackmyFoot:my_DC_JackJ3
1GS1010FLmyFoot:my_D_GS1010FLD9
1HEF4027BTmyFoot:my_SOIC-16_3.9x9.9mm_Pitch1.27mmU2
1INPUTmyFoot:my_Phone_Jack1J1
1LEDLED_THT:LED_D3.0mmD7
1OPA1679myFoot:my_TSSOP-14U1
1OUTPUTmyFoot:my_Phone_Jack1J2
1SW_PushmyFoot:my_SKHCBFA010SW1

The 76 most common of 88 parts.

More from kanengomibako/EffectsPedals

12
  • 2 layers55.4 × 66 mmOwmBoard, the printed circuit board in 3D

    OwmBoard

    kanengomibako/EffectsPedals

    166 parts14Unlicense
  • 2 layers112 × 80 mmBddi v1ep, the printed circuit board in 3D

    Bddi v1ep

    kanengomibako/EffectsPedals

    146 parts14Unlicense
  • 2 layers90 × 100 mmBd2wl, the printed circuit board in 3D

    Bd2wl

    kanengomibako/EffectsPedals

    144 parts14Unlicense
  • 2 layers54 × 83 mmMTZone, the printed circuit board in 3D

    MTZone

    kanengomibako/EffectsPedals

    120 parts14Unlicense
  • 4 layers49.5 × 49.5 mmOwmH7D, the printed circuit board in 3D

    OwmH7D

    kanengomibako/EffectsPedals

    118 parts14Unlicense
  • 2 layers99.1 × 80 mmTremolec, the printed circuit board in 3D

    Tremolec

    kanengomibako/EffectsPedals

    103 parts14Unlicense
  • 2 layers61 × 100 mmBd2op, the printed circuit board in 3D

    Bd2op

    kanengomibako/EffectsPedals

    102 parts14Unlicense
  • 2 layers100 × 100 mmBddi v1el, the printed circuit board in 3D

    Bddi v1el

    kanengomibako/EffectsPedals

    94 parts14Unlicense
  • 2 layers49.5 × 54.6 mmOwmAN, the printed circuit board in 3D

    OwmAN

    kanengomibako/EffectsPedals

    88 parts14Unlicense
  • 2 layers54.6 × 48.3 mmBD21, the printed circuit board in 3D

    BD21

    kanengomibako/EffectsPedals

    76 parts14Unlicense

Similar boards

  • 2 layers148 × 110 mm810, the printed circuit board in 3D

    810

    minisystem/810

    800 series VCO/VCF/VCA

    334 parts10
  • 2 layers49.5 × 42.5 mmGeiger, the printed circuit board in 3D

    Geiger

    SyrianSpock/open-geiger-counter

    PIN diode based Geiger counter

    44 parts6
  • 2 layers133.4 × 50 mmVoice, the printed circuit board in 3D

    Voice

    minisystem/Apollo

    Programmable Polyphonic Synthesizer

    426 parts1
  • 2 layers96.5 × 62 mmN20 ADCControl, the printed circuit board in 3D

    N20 ADCControl

    deqit/PhilipsPM2528

    Hardware and software for the Philips PM2528

    36 parts3
  • 4 layers36 × 95 mmINPUT, the printed circuit board in 3D

    INPUT

    skylar-slideshows/Digilog_Capstone

    105 parts3
  • 2 layers120 × 130 mmSingularitySurfer V1, the printed circuit board in 3D

    SingularitySurfer V1

    nkrackow/SingularitySurfer-FPGA-Lock-In-Amplifier

    Repository for the development of an FPGA based DSP Lock-In Amplifier

    174 parts80MIT
  • 4 layers75 × 36 mmEmoeNAP, the printed circuit board in 3D

    EmoeNAP

    Floyd-Fish/Noise-Amplifier

    An ultra-low noise amplifier to measure low-noise LDO/OPA's wide band output noise, and many other interesting measurements. Referred to AN-159.

    189 parts36GPL-3.0
  • 2 layers49.5 × 106 mmSupra board, the printed circuit board in 3D

    Supra board

    jsenzel1/supra

    is multimode Eurorack module with 4 different experiments in long term time. you can run up to 2 modes at once. use the 4 way joystick and buttons to interact with the modes on the oled

    119 parts4

Questions

How big is the Ds1 PCB?

It measures 73 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ds1 use?

88 parts, built around the OPA1679ID, HEF4027BT, 1N4148W and 2SK208-GR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ds1 KiCad files?

From the kanengomibako/EffectsPedals repository on GitHub, at the commit this page was made from: the board is DS1Op/KiCad/ds1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ds1 design in my own project?

Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).