

Swallow
designs
- Size
- 75.8 × 74.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 42
- Pads
- 162
- Tracks, vias
- 345, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Aug 2025
- Updated
- 16 Feb 2026
Overview
Swallow is an open-source printed circuit board by kamangir, from the kamangir/bluer-designs repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 75.8 × 74.2 mm with 36 parts on 42 nets, routed with 345 tracks and 0 vias.
It is built around the P6KE6.8A. Its parts include 15 resistors, 10 connectors, 8 diodes, 1 capacitor and 1 switch. It belongs with the robots and motor control boards of this library.
Main components
1README
README.mdParts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 330 ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R6, R8, R11, R14 |
| 4 | 2.2 kohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4, R9, R12, R15 |
| 4 | 3.3 kohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R7, R10, R13 |
| 4 | blue | LED_THT:LED_D5.0mm | D5, D6, D7, D8 |
| 1 | 470 µF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1 |
| 1 | P6KE6.8A | Diode_THT:D_DO-15_P10.16mm_Horizontal | D4 |
| 1 | Raspberry Pi: 0, 3, 4 or 5 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | VCC | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J4 |
| 1 | echo1 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J7 |
| 1 | echo2 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J2 |
| 1 | echo3 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J5 |
| 1 | echo4 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J6 |
| 1 | evens | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J10 |
| 1 | green | LED_THT:LED_D5.0mm | D3 |
| 1 | ground | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J3 |
| 1 | odds | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J9 |
| 1 | power terminal | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J8 |
| 1 | red | LED_THT:LED_D5.0mm | D2 |
| 1 | yellow | LED_THT:LED_D5.0mm | D1 |
The 35 most common of 36 parts.
Similar boards
- 2 layers80.5 × 92 mm

- 2 layers200 × 170 mm

- 2 layers120 × 40 mm

Lemon piano
yupipi93/arduino-lemon-piano
Hold a ground clip in one hand and touch a lemon with the other: your body closes the circuit, the pin drops three or four ADC counts, and a note sounds. Seven lemons make a keyboard.
49 parts - 2 layers78.5 × 104.5 mm

- 2 layers65 × 30 mm

Rgb to hdmi
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
36 parts1kGPL-3.0 - 2 layers55 × 70 mm

Arduino v1
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
36 parts915 - 2 layers50.4 × 24.8 mm

- 2 layers45.7 × 31.8 mm

LEDx16 board
tardate/LittleArduinoProjects
a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!
36 parts803MIT
Questions
How big is the Swallow PCB?
It measures 75.8 × 74.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Swallow use?
36 parts, built around the P6KE6.8A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Swallow KiCad files?
From the kamangir/bluer-designs repository on GitHub, at the commit this page was made from: the board is swallow/kicad/swallow/swallow.kicad_pcb and its schematic swallow/kicad/swallow/swallow.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Swallow design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
