Skip to the content
2 layers18.8 × 36.1 mmPicoballoon, the printed circuit board in 3D

Brno Observatory Picoballoon Competition probe for 2021

Size
18.8 × 36.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
33
Nets
29
Pads
151
Tracks, vias
506, 32
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
16 Apr 2021
Updated
29 Jun 2021

Overview

Picoballoon is an open-source printed circuit board by kajusK, from the kajusK/Picoballoon2021 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 18.8 × 36.1 mm with 33 parts on 29 nets, routed with 506 tracks and 32 vias.

It is built around the MCP1640-I/MC, RFM95W-868S2 and SRN2510F-4R7M. Its parts include 11 capacitors, 9 resistors, 5 ICs, 5 connectors and 1 inductor. It belongs with the sensors and measurement boards and the STM32 boards of this library.

Main components

3

README

README.md

Picoballoon Challenge 2021, Deadbadger probe

This probe was designed Picoballoon Challenge organised by Brno Observatory and Planetarium. A goal of this competition is to make a probe under 20 grams that would be launched on ballon to altitudes around 5-15 km. Only requirement except weight is sending current altitude of the probe.

probe

A detailed description is available at deadbadger.cz, tracking site is at bal.deadbadger.cz.

The probe contains

  • STM32F051 MCU
  • MS5607 Pressure and temperature sensor
  • Quectel L96 GPS module with integrated antenna
  • RFM95 LoRa Transceiver
  • MCP1640 based 3.3V boost regulator

Firmware

As the commonly used LMIC library is quite bulky and far from perfect, I wrote my own LoRaWan library inspired by TinyLoRa.

The main loop does about this:

  • Power up, initialize peripherals
  • Measure system voltages, pressure
  • Wait for GPS data or timeout
  • Power off GPS
  • Send data over LoRa (ABP, unconfirmed uplink)
  • Power off RFM95 trancesiver
  • Power off for 30 minutes
  • Repeat (GPS is powered on every 4th cycle)

Hardware

The board was designed for 0.6 mm thick two sided PCB to reduce weight as much as possible. Using thicker boards (usually 1.6 mm) changes the antenna trace impedance, but it should not be that significant.

The programming and debug uart connectors are separated from the main layout and this piece of the PCB will be snapped off before launch to reduce weight.

Power consumption with 3 V power supply

  • board topped at 50 mA with GPS searching for satellites, RFM in standby and MCU running
  • 7,3 mA with GPS powered off
  • 5,3 mA with RFM95 in sleep mode and GPS off
  • 45 uA with devices powered off

Weight

  • 10 g - Battery
  • ~3 g - Probe PCB with programming header
  • 12,39 g - Take off weight, officially measured

Frontend

Data received by TTN are sent over HTTP integration to custom web server that verifies the auth header and stores data in sqlite database.

User frontend is written in python, it shows all received packets, flight route and current position on a map. The tracker is available at bal.deadbadger

To run the frontend in docker, run

text
docker build -t picoballon .
mkdir /srv/probe
touch /srv/probe/database.sqlite
# set token to use in auth header
echo "someuser:somepassword" > /srv/probe/token.txt
docker run -v /srv/probe/data:/project/cloud_data --mount type=bind,source=/srv/probe/database.sqlite,target=/project/database.sqlite --mount type=bind,source=/srv/probe/credentials.txt,target=/project/credentials.txt -p 8081:80 --name picoballon -d picoballon

Parts

33
QtyValueFootprintReferences
7100nCapacitor_SMD:C_0603_1608MetricC2, C4, C5, C7, C8, C10, C12
410kResistor_SMD:R_0603_1608MetricR1, R2, R4, R5
410uCapacitor_SMD:C_0603_1608MetricC1, C6, C9, C11
21MResistor_SMD:R_0603_1608MetricR6, R9
1390kResistor_SMD:R_0603_1608MetricR8
1560kResistor_SMD:R_0603_1608MetricR3
1680kResistor_SMD:R_0603_1608MetricR7
1ANTConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ5
1BATT+Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_VerticalJ1
1BATT-Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ2
1DEBUGConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ3
1L96RF_GPS:Quectel_L96U3
1MCP1640Package_TO_SOT_SMD:SOT-23-6U5
1MS5607-02BAPackage_LGA:LGA-8_3x5mm_P1.25mmU1
1PWR_CUTJumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mmJP1
1RFM95W-868S2RF_Module:HOPERF_RFM9XW_SMDU6
1SRN2510F-4R7MInductor_SMD:L_Abracon_ASPI-3012SL1
1STM32F051K8TxPackage_QFP:LQFP-32_7x7mm_P0.8mmU4
1SWDConnector_PinHeader_1.27mm:PinHeader_2x03_P1.27mm_Vertical_SMDJ4

The 32 most common of 33 parts.

Similar boards

  • 2 layers22.3 × 49.9 mmBaloon, the printed circuit board in 3D

    Baloon

    kajusK/Picoballoon2020

    Probe for Observatory and Planetarium Brno Picoballoon Challenge 2020

    66 partsGPL-3.0
  • 2 layers41 × 56.3 mmPicobaloon, the printed circuit board in 3D

    Picobaloon

    kajusK/picoballoon

    Picoballoon challange on Brno observatory. Team Deadbadger.

    51 parts
  • 4 layers130 × 25 mmCurrent sense, the printed circuit board in 3D

    Current sense

    westonb/little-bee-B1

    A high performance current & magnetic field probe

    113 parts331CC-BY-SA-4.0
  • 2 layers142.2 × 132.1 mmInterphase, the printed circuit board in 3D

    Interphase

    Durburz/interphase

    a mitosis clone with more keys!!1eleven

    115 parts50MIT
  • 2 layers100 × 100 mmWifi PB panel, the printed circuit board in 3D

    Wifi PB panel

    AntonioMR/Wifi-Play-Board

    Placa de experimentacion para el ESP12F (ESP8266)

    416 parts29
  • 2 layers76.2 × 147.3 mmAriCalculator RevC, the printed circuit board in 3D

    AriCalculator RevC

    hotwolf/AriCalculator

    A homemade pocket calculator

    513 parts15GPL-3.0
  • 4 layers160 × 65 mmCapybara rocket, the printed circuit board in 3D

    Capybara rocket

    adam-kabbara/RSX-CANSAT-2026

    This is a repository design to manage the files made by the Aerial team under the Robotics for Space eXploration design team at the University of Toronto

    174 parts4
  • 2 layers200 × 120 mmPlytka v2, the printed circuit board in 3D

    Plytka v2

    tmierzwa/WICI

    Otwarty system łączności awaryjnej (Reticulum/LXMF, 869 MHz)

    152 parts4

Questions

How big is the Picoballoon PCB?

It measures 18.8 × 36.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Picoballoon use?

33 parts, built around the MCP1640-I/MC, RFM95W-868S2 and SRN2510F-4R7M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Picoballoon KiCad files?

From the kajusK/Picoballoon2021 repository on GitHub, at the commit this page was made from: the board is hw/picoballoon.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Picoballoon design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).