
Weather balloon V1.0
Launchpad-Incubator/weather-balloon
The research repository for Launchpad's flat-packed weather balloons.

Weather station is an open-source printed circuit board by kaat22, from the kaat22/weather_station repository on GitHub. It is a 2-layer board of 85 × 91 mm with 34 parts on 51 nets, routed with 447 tracks and 24 vias.
It is built around the ESP32-WROOM-32, AM2302 and BMP280. Its parts include 11 resistors, 9 capacitors, 7 connectors, 5 ICs and 1 diode. It belongs with the home automation and IoT boards and the ESP32 boards of this library.
The purpose of this project was to make a weather station (Figure 1), which will read and send the measurements to a server.
The basic aim was to make a functional weather station, which would send the data to a server, that could then be read from a computer. Our secondary aim was to make the weather station rechargeable, using a LiFePO4 battery (Figure 2). Using a battery to power the station allows it to work without being connected to a computer or a power outlet.
The microcontroller we used in the project was ESP32-WROOM-32E (Figure 3). The microcontroller has built-in Wi-Fi that allows it to send the data to a server. There are two sensors which measure the temperature, humidity and air pressure.
We achieved our primary goal of gathering and transferring data (via Wi-Fi) from the station's sensors to a server, wherefrom it can be viewed through a web browser. We also partially achieved our secondary goal of powering the device with a rechargeable battery, however due to an error in the pcb design phase we were unable to get the recharging feature of the charging circuit functional.
ESP-32WROOM-32E datasheet Source:
esp32-wroom-32e_esp32-wroom-32ue_datasheet_en.pdf (espressif.com)
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R7, R10, R11 |
| 3 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C9, C10 |
| 2 | 1000 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R3 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C7 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R9 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 1 | 100nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 500 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | ADP5063 | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U4 |
| 1 | AM2302 | Sensor:ASAIR_AM2302_P2.54mm_Vertical | U3 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_1042_1x18650 | BT1 |
| 1 | Conn_01x01_Pin | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J7 |
| 1 | Conn_01x02_Pin | TestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | J5 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | Conn_01x11_Pin | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J6 |
| 1 | Conn_02x03_Odd_Even | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J3 |
| 1 | Conn_02x05_Odd_Even | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J2 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32D | U5 |
| 1 | LD1117S33TR_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J1 |

Launchpad-Incubator/weather-balloon
The research repository for Launchpad's flat-packed weather balloons.

tjiuce/rover
Rover Navigation Optimization System (R-NOS): An ESP32-powered autonomous robotic prototype designed for real-time environmental monitoring.

Aanuoluwap/555blinker
This repository contains electronics design projects created using KiCad.



Ndambia/lilygo
A custom 4-layer KiCad PCB design integrating an ESP32 Wi-Fi/Bluetooth microcontroller with a SIM7600G-H 4G LTE Cat-4 cellular module, comprehensive power management, GPS tracking, GPRS connectivity, USB-C charging…

Vinay-Kumbar/SensorNode-PCB-Design
PCB design for a multi-sensor node (ESP32, DHT22, vibration sensor) built in KiCad — schematic, layout, and manufacturing files

It measures 85 × 91 mm and has 2 copper layers, 1.6 mm thick.
34 parts, built around the ESP32-WROOM-32, AM2302 and BMP280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the kaat22/weather_station repository on GitHub, at the commit this page was made from: the board is pcb_kicad/weather_station.kicad_pcb and its schematic pcb_kicad/weather_station.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask kaat22 before reusing the design.