

BurnedHead
A handheld game console
- Size
- 121.9 × 44.4 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 92
- Nets
- 164
- Pads
- 546
- Tracks, vias
- 1,928, 375
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Nov 2019
- Updated
- 10 Aug 2021
Overview
BurnedHead is an open-source printed circuit board by justinbalexander, from the justinbalexander/BurnedHead repository on GitHub, published under the Unlicense licence. It is a 4-layer board of 121.9 × 44.4 mm with 92 parts on 164 nets, routed with 1,928 tracks and 375 vias.
It is built around the PAM8302AASCR, TPS61169DCK and MT48LC16M16A2TG, with the RT9013-33GB, 1N4148WS and 1206L150THWR among its other parts. Its parts include 36 capacitors, 25 resistors, 8 ICs, 8 switches and 5 diodes. It belongs with the STM32 boards of this library.
Main components
10PAM8302AASCR
MSOP-8-40℃~+85℃ 0.3% 1-Channel 2.5Wx1@4Ω 2V~5.5V 4mA 50dB 80dB 85% Class D Filterless architecture MSOP-8 Audio Amplifiers ROHSDiodes IncorporatedAudio AmplifiersTPS61169DCK
SC-70-5-40℃~+125℃ 1 1.2MHz 1.8A 2.7V~38V 2.7V~5.5V Boost Built-in DC-DC PWM Short Circuit Protection、Over Voltage Protection、Over-Temperature Protection (OTP)、LED open-circuit protection、Built-in soft-start SC-70-5 LED Drivers ROHSTexas InstrumentsLED DriversMT48LC16M16A2TG
TSOP-54TSOP-54 DRAM ROHSMicron TechDRAMRT9013-33GB
SOT-23-5-40℃~+125℃@(Tj) 1 25uA 3.3V 30uVrms 400mV@(500mA) 5.5V 500mA 50dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRICHTEKVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes1206L150THWR
1206-40℃~+85℃ 1.5A 100A 120mΩ 300ms 3A 40mΩ 800mW 8V 1206 Resettable Fuses ROHSLittelfuseResettable FusesIRLML6401TRPBF
SOT-23-55℃~+150℃ 1 P-Channel 1.3W 125pF 12V 15nC@5V 180pF 4.3A 50mΩ@4.5V 830pF 950mV SOT-23 MOSFETs ROHSInfineon TechnologiesMOSFETsNSR0240H
SOD-323-55℃~+150℃ 1 Independent 10uA@40V 1A 250mA 40V 710mV@200mA SOD-323 Schottky Diodes ROHSonsemiSchottky DiodesSMF12CA
SOD-123FLESD And Surge Protection (TVS/ESD)hongjiachengSNR4018K-6R8M
SMD,4x4mm1.3A 124mΩ 6.8uH ±20% SMD,4x4mm Power Inductors ROHS3L COILSPower Inductors
README
README.mdBurnedHead
A handheld, portable video game system designed with Kicad and programmed in C.
Description
The processor is the STM32F767ZG, a Cortex-M7 processor selected for the ample size of the instruction and data caches. Currently at the board bring-up stage, the functionality includes an RGB parallel interface, an MMC card socket, a 32MB SDRAM clocked at 108MHz, D-pad, 4 front facing buttons, 2 shoulder buttons, 2 joysticks, and a speaker. The device is powered through a Micro-USB connector or a rechargeable LiPo battery for portability.
The final product will load user-selectable ELF files off of the MMC compatible card into the external RAM and run them as a process.
The project originally began in Zig but is transitioning to C to reduce friction when integrating with libraries and vendor code and to allow progress without requiring fiddling with a language still in beta.
Building
Cloning the Repository
This repository uses submodules to manage dependencies.
git clone --recurse-submodules https://github.com/vegecode/BurnedHead.gitBuilding the Application
BurnedHead uses Makefiles. Navigate to the base directory of the clone, and point to the specific Makefile you want to build (currently only one):
Example:
make -f configurations/${CONFIGURATION_NAME}/MakefileThe resulting executable(s) are in ./build/${CONFIGURATION_NAME}
Debugging on the Target
Debugging is done using GDB in a shell with the JLink GDBServer providing the connection to the remote target.
Running the shell script ./debug/start_debug /path/to/elf_file will start the
GDBServer and connect GDB to it, then a gdb script loads the executable and sets
a temporary breakpoint at the reset handler.
A sample of some external RAM tests during board bring-up in a Vim/GDB session:

Another easy alternative if you are using a JLink debug probe is to use Ozone, the standalone debugger from Segger or Segger Embedded Workbench which are both free to use for non-commercial purposes.
Integrating with Eclipse should also be possible using the MCU GNU Eclipse plugins.
Hand-Assembled Revision 0 Board
The back of the first revision of the board was assembled using solder paste and a cast-iron skillet over a stand-alone burner for reflow. Some rework was required as applying the paste without a stencil resulted in uneven application. The front side components were hand soldered.


Renders


Attributions
Some symbols and footprints came from www.snapeda.com. See the library folder for the required license and attributions.
Parts
92| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | C100nF | Capacitor_SMD:C_0603_1608Metric | C10, C13, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26, C27, C28 +6 |
| 9 | 10K | Resistor_SMD:R_0603_1608Metric | R4, R5, R10, R11, R13, R14, R15, R16, R17 |
| 6 | C1uF | Capacitor_SMD:C_0603_1608Metric | C3, C5, C7, C8, C29, C34 |
| 5 | 47K | Resistor_SMD:R_0603_1608Metric | R22, R23, R24, R25, R26 |
| 4 | 100K | Resistor_SMD:R_0603_1608Metric | R3, R6, R7, R9 |
| 3 | 2K | Resistor_SMD:R_0603_1608Metric | R2, R18, R19 |
| 3 | C4.7uF | Capacitor_SMD:C_0805_2012Metric | C2, C4, C6 |
| 3 | SW_Push | Button_Switch_SMD:SW_SPST_PTS645 | SW2, SW5, SW6 |
| 2 | 1N4148WS | Diode_SMD:D_SOD-323 | D2, D5 |
| 2 | C10uF | Capacitor_SMD:C_1206_3216Metric | C14, C31 |
| 2 | C2.2uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | FPC_1x5_TopContact_P=0.5mm | parts-lib:XKB-Enterprise_X05B20U05T_1x05_P0.50mm_Horizontal | J4, J5 |
| 2 | SW_Push | Button_Switch_SMD:Panasonic_EVQPUL_EVQPUC | SW3, SW8 |
| 1 | 10.2 1% | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 1206L150TH | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 2R2 | Resistor_SMD:R_1206_3216Metric | R21 |
| 1 | 51296-5494 | parts-lib-SnapEDA:51296 | U4 |
| 1 | C22nF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | DFLS130L-7 | Diode_SMD:D_PowerDI-123 | D3 |
| 1 | DM3AT-SF-PEJMS | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J3 |
| 1 | DualShock-4Buttons | parts-lib:PS4-DualShock-CarbonPad-4Buttons | SW7 |
| 1 | DualShock-DPad | parts-lib:PS4-DualShock-CarbonPad-DPad | SW4 |
| 1 | IRLML6401TRPBF | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | LiPo_P1.25_THRU | Connector_Molex:Molex_PicoBlade_53048-0410_1x02_P1.25mm_Horizontal | BT1 |
| 1 | MCP73832-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | MT48LC16M16A2 | parts-lib-SnapEDA:MT48LC16M16A2TG-6A_IT | U7 |
| 1 | NSR0240 | Diode_SMD:D_SOD-323 | D4 |
| 1 | PAM8302AAS | Package_SO:MSOP-8_3x3mm_P0.65mm | U8 |
| 1 | RT9013-33GB | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | SMF12CA | Diode_SMD:D_SOD-123F | D1 |
| 1 | SNR4018K-6R8M | Inductor_SMD:L_Taiyo-Yuden_NR-40xx | L1 |
| 1 | STM32F767ZGTx | Package_QFP:LQFP-144_20x20mm_P0.5mm | U6 |
| 1 | SW_SPDT | Button_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_Angled | SW1 |
| 1 | Speaker | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | LS1 |
| 1 | TPS61169 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U3 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J1 |
| 1 | XO_8MHz_SMD | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | U5 |
Similar boards
- 4 layers62.5 × 96.2 mm

- 2 layers84.9 × 51.2 mm

- 2 layers131.5 × 85.8 mm

- 4 layers100 × 100 mm

- 4 layers65 × 45 mm

Lora gps tracker rev a
bogdan-kovalchuk/esp32-lora-gps-tracker
Encrypted point-to-point GPS telemetry over 433 MHz LoRa between two ESP32 boards.
69 partsMIT - 4 layers65 × 64.5 mm

- 4 layers250.8 × 30 mm

- 2 layers33 × 46 mm

M18-usb interface pcb
fred314159265/m18-usb-interface
Isolated USB-C adapter for Milwaukee M18 battery diagnostics. KiCad design and v1.0 fab files. Software: m18-protocol-rs.
31 partsUnlicense
Questions
How big is the BurnedHead PCB?
It measures 121.9 × 44.4 mm and has 4 copper layers, 1.6 mm thick.
What parts does the BurnedHead use?
92 parts, built around the PAM8302AASCR, TPS61169DCK, MT48LC16M16A2TG and RT9013-33GB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BurnedHead KiCad files?
From the justinbalexander/BurnedHead repository on GitHub, at the commit this page was made from: the board is pcb/BurnedHead.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the BurnedHead design in my own project?
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).