Skip to the content
12345678

PAM8302AASCR

Diodes IncorporatedExtended

-40℃~+85℃ 0.3% 1-Channel 2.5Wx1@4Ω 2V~5.5V 4mA 50dB 80dB 85% Class D Filterless architecture MSOP-8 Audio Amplifiers ROHS

Part id
diodes/PAM8302AASCR
Category
Audio Amplifiers
Package
MSOP-8
Pins
8
In stock
7,776 at JLCPCB (C113367)
Used on
44 open-source boards

Overview

The PAM8302AASCR is an audio Amplifier made by Diodes Incorporated in a MSOP-8 package with 8 pins. -40℃~+85℃ 0.3% 1-Channel 2.5Wx1@4Ω 2V~5.5V 4mA 50dB 80dB 85% Class D Filterless architecture MSOP-8 Audio Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Amplifier_Audio:PAM8302AAS, from KiCad's library) and its footprint (Package_SO:MSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 7,776 are in stock at JLCPCB (part C113367). 44 open-source boards in 32 repositories on GitHub use it.

Symbol

1SD3IN+4IN-5OUT+6VDD7GND8OUT-
Amplifier_Audio:PAM8302AASFrom KiCad's library

Footprint

12345678
Package_SO:MSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

10
Supply, least
2 V · VDD, recommended operating min · p. 3
Supply, most
5.5 V · VDD, recommended operating max · p. 3
Supply, absolute maximum
6 V · VDD, absolute max at no input signal · p. 2
Works from
-40 °C · Operating ambient min · p. 3
Works up to
85 °C · Operating ambient max · p. 3
Junction, hottest
150 °C · Junction temperature absolute max · p. 2
Takes working
4 mA · VDD, typical quiescent current, no load · p. 3
Takes asleep
1 µA · VDD, shutdown current max, VSHDN = 0V · p. 3
Switches at
250 kHz · Oscillator frequency typical · p. 3
Junction to air (MSOP-8)
180 K/W · Junction to ambient thermal resistance max · p. 3

What it is and has

7
Amplifier
2.5W Class-D mono · p. 1
Architecture
Filterless · p. 1
Efficiency
Up to 88% · p. 1
Protection
Short circuit protection · p. 1
Protection
Thermal shutdown · p. 1
Package options
MSOP-8, SO-8, U-DFN3030-8 (Type E) · p. 1
Compliance
Lead-free, RoHS compliant · p. 1

Around it

4
cap 0.1µF to 0.22µF
between Input source + and IN+; Input coupling capacitor; low leakage tantalum or ceramic recommended. · p. 7
cap 1.0µF
between VDD and GND; Low ESR ceramic; place as close as possible to VDD. · p. 8
cap 10µF or larger
between VDD and GND; Place near the amplifier to filter lower frequency supply noise. · p. 8
cap 1000μF
between VDD and GND; Additional supply capacitor for reducing power line coupling when speaker traces are shorter than 20CM. · p. 8

Specifications

38
ParameterConditionsAs printedPage
Supply Voltage at No Input SignalTA = +25°Cmax 6 V2
Input VoltageTA = +25°C; upper limit VDD +0.3 Vmin -0.3 V2
Maximum Junction Temperaturemax 150 °C2
Storage Temperaturemin -65 · max 150 °C2
Soldering Temperature5smax 300 °C2
Supply Voltage RangeTA = +25°C, unless otherwise specifiedmin 2 · max 5.5 V3
Operation Temperature Rangemin -40 · max 85 °C3
Junction Temperature Rangemin -40 · max 125 °C3
Thermal Resistance (Junction to Ambient) θJAMSOP-8max 180 °C/W3
Supply Voltage Range VDD—min 2 · max 5.5 V3
Quiescent Current IQNo Loadtyp 4 · max 8 mA3
Shutdown Current ISHDNVSHDN = 0Vmax 1 uA3
Output Power POf = 1kHz, RL = 4Ω, THD+N = 10%, VDD = 5Vmin 2.25 · typ 2.5 W3
Output Power POf = 1kHz, RL = 4Ω, THD+N = 10%, VDD = 3.6Vmin 1.1 · typ 1.25 W3
Output Power POf = 1kHz, RL = 4Ω, THD+N = 1%, VDD = 5Vmin 1.8 · typ 2 W3
Output Power POf = 1kHz, RL = 4Ω, THD+N = 1%, VDD = 3.6Vmin 0.86 · typ 0.95 W3
Output Power POf = 1kHz, RL = 8Ω, THD+N = 10%, VDD = 5Vmin 1.35 · typ 1.5 W3
Output Power POf = 1kHz, RL = 8Ω, THD+N = 10%, VDD = 3.6Vmin 0.72 · typ 0.8 W3
Output Power POf = 1kHz, RL = 8Ω, THD+N = 1%, VDD = 5Vmin 1.15 · typ 1.3 W3
Output Power POf = 1kHz, RL = 8Ω, THD+N = 1%, VDD = 3.6Vmin 0.6 · typ 0.65 W3
Peak Efficiency ηf = 1kHztyp 85 · max 88 %3
Total Harmonic Distortion Plus Noise THD+NRL = 8Ω, PO = 0.1W, f = 1kHztyp 0.3 · max 0.35 %3
Total Harmonic Distortion Plus Noise THD+NRL = 8Ω, PO = 0.5W, f = 1kHztyp 0.45 · max 0.5 %3
Total Harmonic Distortion Plus Noise THD+NRL = 4Ω, PO = 0.1W, f = 1kHztyp 0.35 · max 0.4 %3
Total Harmonic Distortion Plus Noise THD+NRL = 4Ω, PO = 0.5W, f = 1kHztyp 0.4 · max 0.45 %3
Gain GV—typ 23.5 dB3
Power Supply Ripple Rejection PSRRNo Inputs, f = 1kHz, VPP = 200mVmin 45 · typ 50 dB3
Dynamic Range DYNf = 20 to 20kHzmin 85 · typ 90 dB3
Signal to Noise Ratio SNRf = 20 to 20kHzmin 75 · typ 80 dB3
Noise VNNo A-Weightingtyp 180 · max 300 uV3
Noise VNA-Weightingtyp 120 · max 200 uV3
Oscillator Frequency fOSC—min 200 · typ 250 · max 300 kHz3
Drain-Source On-State Resistance RDS(ON)IDS = 100mA, P MOSFETtyp 0.45 · max 0.5 Ω3
Drain-Source On-State Resistance RDS(ON)IDS = 100mA, N MOSFETtyp 0.2 · max 0.25 Ω3
SHD Input High VSH—min 1.2 V3
SHD Input Low VSL—max 0.4 V3
Over Temperature Protection OTPJunction Temperaturemin 120 · typ 135 °C3
Over Temperature Hysteresis OTH—typ 30 °C3

Ordering codes, by the datasheet

3
PAM8302AASCR
MSOP-8 · 2500 Units/Tape & Reel · p. 9
PAM8302AADCR
SO-8 · 2500 Units/Tape & Reel · p. 9
PAM8302AAYCR
U-DFN3030-8 (Type E) · 3000 Units/Tape & Reel · p. 9

Open-source boards using it

44See all 44
  • 4 layers121.9 × 44.4 mmBurnedHead, the printed circuit board in 3D

    BurnedHead

    justinbalexander/BurnedHead

    A handheld game console

    92 parts45Unlicense
  • 4 layers25.3 × 35.1 mmAgb hifi audio pcb, the printed circuit board in 3D

    Agb hifi audio pcb

    cajunpanda/gameboy-hifi-audio

    A HiFi audio mod for various Game Boy models

    66 parts25MIT
  • 2 layers81 × 55 mmFABI schematic, the printed circuit board in 3D

    FABI schematic

    asterics/FABI

    The repository for FABI (Flexible Assistive Button Interface)

    80 parts22
  • 4 layers54.7 × 78.5 mmDisplayModule PONSv71, the printed circuit board in 3D

    DisplayModule PONSv71

    MasaoC/GPS-TFT-Map_PONS

    鳥人間コンテストに特化したGNSS誘導システム。人力飛行機のパイロットが使いやすいことを目標にした航法装置です。ハードとソフトをオープンソースで開発しています。

    151 parts14MIT
  • 2 layers82.5 × 136.7 mmGameboy dmg, the printed circuit board in 3D

    Gameboy dmg

    alxhoff/gameboy-dmg-pcb

    PCB for Gameboy DMG with audio and GPIO expander to provide I2C interface to push buttons

    95 parts4GPL-3.0
  • 4 layers182 × 150 mmStarman, the printed circuit board in 3D

    Starman

    adamm/starman

    Starman Christmas Tree Topper PCB

    248 parts3
  • 2 layers58 × 44 mmButton, the printed circuit board in 3D

    Button

    birkenfeld/stm_button_rust

    Using nightly Rust and cargo, just do a cargo build --release.

    40 parts3

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the PAM8302AASCR?

Yes. The symbol is Amplifier_Audio:PAM8302AAS and the footprint Package_SO:MSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the PAM8302AASCR?

MSOP-8, with 8 pins. Its footprint is drawn on this page.

Where is the PAM8302AASCR datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the PAM8302AASCR?

JLCPCB lists it as part C113367, with 7,776 in stock; the sellers' links on this page open their listings.

What can replace the PAM8302AASCR?

Parts like it in the library: the NS4150B by Shenzhen Nsiway Tech, the LM4890S by IDCHIP, the LM4890SS by IDCHIP and the LN4890MME-G by NATLINEAR. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the PAM8302AASCR?

44 boards in 32 repositories on GitHub; the most starred are listed on this page, with their KiCad files.