

Solar Powered Egg Incubator
- Size
- 100 × 90.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 105
- Nets
- 86
- Pads
- 348
- Tracks, vias
- 813, 265
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 Oct 2025
- Updated
- 4 Nov 2026
Overview
Solar Powered Egg Incubator is an open-source printed circuit board by jsitech4, from the jsitech4/Projects repository on GitHub. It is a 2-layer board of 100 × 90.1 mm with 105 parts on 86 nets, routed with 813 tracks and 265 vias.
It is built around the CH340C, ESP32-WROOM-32 and AHT20, with the AMS1117-3.3, TIP41 and UMH3N among its other parts. Its parts include 26 capacitors, 23 resistors, 12 diodes, 11 connectors and 5 ICs. It belongs with the power boards and the ESP32 boards of this library.
Main components
6CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAHT20
SMD-40℃~+120℃ 0%RH~100%RH 2.2V~5.5V 20bit 570uA I2C ±0.3℃ ±2%RH SMD Temperature and Humidity Sensor ROHSAosong ElecTemperature And Humidity SensorAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTIP41
TO-220TO-220 Bipolar (BJT) ROHSTFBipolar Transistors - BJTUMH3N
SOT-363-55℃~+150℃ 0.5uA 100 100mA 150mW 2 NPN (Pre-Biased) 250MHz 300mV 50V 5V 6.11kΩ NPN SOT-363 Digital Transistors ROHSJiangsu Changjing Electronics Technology (CJ)Digital Transistors
Parts
105| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C5, C8, C9, C22, C23, C28, C30, C55, C59, C60 |
| 11 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R4, R5, R26, R28, R34, R35, R48, R49, R50, R51 |
| 5 | PC817XI | PCM_Package_DIP_AKL:SMDIP-4_W9.53mm | OC1, OC8, OC9, OC10, OC11 |
| 4 | 680uF_35V | Capacitor_SMD:CP_Elec_10x12.5 | C2, C3, C6, C7 |
| 4 | NS | Resistor_SMD:R_0805_2012Metric | R8, R9, R10, R11 |
| 4 | ~ | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP2, JP3, JP4, JP5 |
| 3 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B_HandSolder | C56, C57, C58 |
| 3 | 1N4007 | Diode_SMD:D_SMA | D23, D24, D25 |
| 3 | 330R | Resistor_SMD:R_0805_2012Metric | R27, R29, R30 |
| 3 | RELAY | Relay_THT:Relay_SPDT_Finder_36.11 | K4, K5, K6 |
| 2 | 150R | Resistor_SMD:R_0805_2012Metric | R53, R54 |
| 2 | 1N5819 | Diode_SMD:D_SMA | D9, D14 |
| 2 | 1N5824 | Diode_SMD:D_SMA | D1, D2 |
| 2 | 220uF_16V | Capacitor_SMD:CP_Elec_6.3x7.7 | C4, C10 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C25, C26 |
| 2 | 3.3V | Diode_SMD:D_SOD-123 | D3, D4 |
| 2 | 33uH | Inductor_SMD:L_12x12mm_H6mm | L1, L2 |
| 2 | 4.7uF/16V | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B_HandSolder | C18, C24 |
| 2 | PC817 | PCM_Package_DIP_AKL:SMDIP-4_W9.53mm | OC13, OC14 |
| 2 | Red | LED_THT:LED_D3.0mm | D8, D11 |
| 1 | 10K | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV2 |
| 1 | 10uF_16V | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C20 |
| 1 | 12MHz | Crystal:Crystal_HC49-4H_Vertical | Y2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R46 |
| 1 | 2k | Resistor_SMD:R_0805_2012Metric | R47 |
| 1 | 470nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C19 |
| 1 | 47k | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | AHT20 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | BMS | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J3 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_15x7.5RM7.6 | BZ6 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U8 |
| 1 | ESP32-WROOM | RF_Module:ESP32-WROOM-32 | U7 |
| 1 | FAN | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J1 |
| 1 | FLASH | Button_Switch_SMD:SW_SPST_CK_KXT3 | SW5 |
| 1 | Green | LED_THT:LED_D3.0mm | D12 |
| 1 | HEATER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J7 |
| 1 | HUMIDIFIER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J6 |
| 1 | LEVELS | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | LM2596S-3.3V | Package_TO_SOT_SMD:TO-263-5_TabPin6 | U1 |
| 1 | LM2596S-5V | Package_TO_SOT_SMD:TO-263-5_TabPin6 | U3 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_CK_KXT3 | SW4 |
| 1 | RTC | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | SCREEN | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J47 |
| 1 | SPINNER | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J2 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | TIP41 | Package_TO_SOT_THT:TO-220-3_Vertical | Q9 |
| 1 | UMH3N | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q2 |
| 1 | USB_C Conn | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J23 |
| 1 | Ultra Sonic | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J42 |
The 101 most common of 105 parts.
More from jsitech4/Projects
8- 4 layers198.1 × 130.8 mm

- 2 layers108.8 × 83.6 mm

- 2 layers101.2 × 76.6 mm

- 2 layers131.3 × 88.7 mm

- 2 layers91.6 × 57.8 mm

- 2 layers105.6 × 92.7 mm

- 2 layers67.3 × 100 mm

- 2 layers97.8 × 137.6 mm

Similar boards
- 2 layers38 × 60 mm

Crossometer mini
fredszaq/crossometer-mini
Design files for crossometer-mini device
63 parts2CERN-OHL-S-2.0 - 2 layers81 × 98 mm

REFLOW OVEN V2
Charading/NETTA-Reflow-Oven-Conversion
I converted my NETTA Mini Oven 20L into a reflow oven.
74 parts - 4 layers65.9 × 52.9 mm

- 4 layers29.9 × 32 mm

Models heart rev1.1
KushlaVR/models-heart
Можливості: Керування через WIFI з телефона або ПК 5 незалежних каналів (світлодіоди/сервомотори) 1 Н-міст для підключення мотора (піковий струм до 3А) Вмонтована BMS 1S та контроллер заряду Li-Ion акумулятора з…
106 parts7GPL-3.0 - 4 layers50.8 × 81.3 mm

Esp32-s3-with ken interface
kawashimaken/general-purpose-ken-interface
A modular, multi-MCU prototyping platform with a unified pin-assignment standard and horizontally-stackable expansion boards.
41 parts3MIT - 4 layers85.6 × 54 mm

Frank air
rh1tech/frank-lab
FRANK Board Laboratory (work-in-progress board prototopyes)
184 parts4GPL-3.0 - 4 layers30 × 37.5 mm

Dongle
mornepousse/SpLiT_KaSe
Custom ergonomic split fully-wireless keyboard - ESP32-S3, NRF24L01+, KiCad 9
31 parts - 2 layers100 × 90 mm

System desgin project
dquang05/system_desgin_project
Academic project - AGV: line following robot
78 parts
Questions
How big is the Solar Powered Egg Incubator PCB?
It measures 100 × 90.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Solar Powered Egg Incubator use?
105 parts, built around the CH340C, ESP32-WROOM-32, AHT20 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Solar Powered Egg Incubator KiCad files?
From the jsitech4/Projects repository on GitHub, at the commit this page was made from: the board is ESP32/Solar_Powered Egg_Incubator/hardware/Solar_Powered_Egg_Incubator.kicad_pcb and its schematic ESP32/Dual_Axis_Solar_Tracker/hardware/Dual_Axis_Solar_Tracker.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Solar Powered Egg Incubator design in my own project?
Its repository states no licence, so its author keeps all rights: ask jsitech4 before reusing the design.