

Power supply2
Various printed circuit board projects
- Size
- 24.6 × 33.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 25
- Nets
- 17
- Pads
- 63
- Tracks, vias
- 58, 77
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Mar 2026
- Updated
- 4 Aug 2026
Overview
Power supply2 is an open-source printed circuit board by jrseti, from the jrseti/pcbs repository on GitHub, published under the MIT licence. It is a 4-layer board of 24.6 × 33.1 mm with 25 parts on 17 nets, routed with 58 tracks and 77 vias.
It is built around the MP2322GQH-Z, 1812L110/33MR and AO3407A, with the DC-005-2.5A-2.0, KF2EDGR-2.54-4P and SMBJ16A among its other parts. Its parts include 9 capacitors, 6 resistors, 3 diodes, 1 IC and 1 transistor.
Main components
9MP2322GQH-Z
QFN-8(1.5x2)-40℃~+125℃@(TJ) 1 1.25MHz 1A 3V~22V 5uA 600mV~12V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Operating status indication、Hiccup current limiting、Built-in LDO regulator、EMI optimization (spread spectrum) Step-down type Yes QFN-8(1.5x2) DC-DC Converters ROHSMonolithic Power SystemsDC-DC Converters1812L110/33MR
1812-40℃~+85℃ 1.1A 1.95A 200mΩ 20A 2mm 3.41mm 33V 4.73mm 500ms 60mΩ 800mW 1812 Resettable Fuses ROHSLittelfuseResettable FusesAO3407A
SOT-231 P-Channel 1.4W 1.8V 14.3nC@4.5V 30V 37mΩ@10V、52mΩ@4.5V 4.2A 700pF 75pF SOT-23 MOSFETs ROHSUMWMOSFETsDC-005-2.5A-2.0
插件-20℃~+70℃ 2mm 6.2mm DC Power Jack Panel Mount 插件 DC Power Connectors ROHSXKB ConnectionDC Power ConnectorsKF2EDGR-2.54-4P
弯插,P=2.54mm-40℃~+105℃ 1 130V 1x4P 2.54mm 4 4P 5A Board Side/Socket - Closed Green Right-Angle 弯插,P=2.54mm Pluggable System Terminal Block ROHSCixi Kefa ElecPluggable System Terminal BlockSMBJ16A
DO-214AA(SMB)16V 19.7V 23.08A 26V 5uA 600W@10/1000us IEC 61000-4-2 TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)SMBJ18A
SMB-65℃~+150℃ 18V 1uA 20.6A 22.1V 29.2V 390pF 600W@10/1000us TVS SMB ESD and Surge Protection (TVS/ESD) ROHSShandong Jingdao MicroelectronicsESD And Surge Protection (TVS/ESD)SS-12F49-G050
插件,12.1x5.9mm-25℃~+70℃ 10000 times 12.1mm 14mm 1A 24V 5.9mm Black PC Pin Rectangular Columnar SPDT Through Hole 插件,12.1x5.9mm Slide Switches ROHSG-SwitchSlide SwitchesSS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
dishy1pi/README.mdDishy1Pi Hardware
The hardware part of the Dishy1Pi project is a Raspberry Pi Hat board which interfaces the Raspberry Pi GPIO pins with the satellite dish motor controllers, encoders, and various sensors. An important aspect of this board is that the Raspberry Pi is optically isolated from the hardware connected to the satellite dish.
Although this project is tailored to controlling a satellite dish, it can also be used for controlling other motor control systems that require isolation and encoder feedback.
Parts Library
The PCB will be assembled by JCLPCB. The project will require parts number identification to be compatible with LCSC part numbers. See Library README
Parts
25| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10uF | PCM_JLCPCB:C_0603 | C11, C111 |
| 1 | 100kΩ | PCM_JLCPCB:R_0603 | R3 |
| 1 | 100nF | MyParts:C0603 | C9 |
| 1 | 100nF | PCM_JLCPCB:C_0603 | C1 |
| 1 | 10kΩ | PCM_JLCPCB:R_0603 | R4 |
| 1 | 1621Ω | MyParts:R0603 | R1 |
| 1 | 1812L110/33MR | MyParts:F1812 | F1 |
| 1 | 1uF | PCM_JLCPCB:C_0402 | C4 |
| 1 | 200kΩ | PCM_JLCPCB:R_0603 | R3 |
| 1 | 220kΩ | PCM_JLCPCB:R_0603 | R2 |
| 1 | 220Ω | PCM_JLCPCB:R_0603 | R2 |
| 1 | 22pF | PCM_JLCPCB:C_0603 | C5 |
| 1 | 22pF | PCM_JLCPCB:C_0402 | C3 |
| 1 | 22uF | PCM_JLCPCB:C_0805 | C2 |
| 1 | 4.7uH | MyParts:IND-SMD_L3.0-W3.0-1 | L1 |
| 1 | 47uF | MyParts:C1206 | C8 |
| 1 | AO3407A | MyParts:SOT-23-3_L2.9-W1.6-P1.90-LS2.8-BR | Q1 |
| 1 | DC-005-2.5A-2.0 | MyParts:CONN-TH_DC-005-2.5A-2.0 | DC1 |
| 1 | KF2EDGR-2.54-4P | MyParts:CONN-TH_4P-P2.54_KF2EDGR-2.54-4P | CN1 |
| 1 | MP2322GQH-Z | MyParts:QFN-8_L2.0-W1.5-P0.50-BL | U1 |
| 1 | SMBJ16A | PCM_JLCPCB:D_SMB | D5 |
| 1 | SMBJ18A | PowerSupply:SMB_L4.6-W3.6-LS5.3-RD | D3 |
| 1 | SS-12F49-G050 | MyParts:SW-TH_SS-12F45-GXXX | SW1 |
| 1 | SS34 | PowerSupply:SMA_L4.3-W2.6-LS5.2-RD | D1 |
More from jrseti/pcbs
3- 4 layers100 × 100 mm

- 4 layers94.6 × 69.3 mm

- 4 layers59.9 × 57.5 mm

Similar boards
- 4 layers24.6 × 33.1 mm

Power supply2
jrseti/dishy1pi
Satellite dish motor control for Raspberry Pi, hardware and software
21 partsMIT - 4 layers150 × 90 mm

Motherboard
Foosa7/koi_8x8
The controller board for Koi 8×8. Carries a Raspberry Pi Pico (RP2040) and hosts up to 8 daughterboards in PCIe-x4 card-edge slots, addressing each board's DAC/ADC over a shared SPI bus. Formerly codenamed MOBO.
56 parts2 - 4 layers150 × 100 mm

Cm4-robo controller
jrseti/roboclaw-cm4-dc-dish-controller
Satellite dish controller using a ROBOCLAW-2X15A-OEM controlled by a Raspberry Pi CM4 module. Powered by DC battery.
292 partsMIT - 4 layers41 × 149 mm

Air filter controller
ademuri/air-filter-controller
The ESP32-S3 uses 3.3V. I want onboard indicator LEDs, and the option to have offboard LEDs as well. Using addressable WS2812-type LEDs is flexible. These need a 5V supply.
167 parts1 - 2 layers60 × 51.5 mm

NanoEvery Replica
arhamrizwan2006/arduino-nano-every-pcb-replica
Chip-level PCB replica of the Arduino Nano Every (ABX00028), designed in KiCad 10 — full schematic, routing, and manufacturing files
23 parts - 4 layers56.6 × 39 mm

Multimodal Actuator mk2
TheUnknownAlias/betr_kicad_resources
This repository contains shared KiCad symbols and footprints for our projects.
91 parts - 2 layers100 × 96 mm

Backlight
jackw01/scanlight
A better light source for scanning color negative film
69 parts397CERN-OHL-W-2.0 - 2 layers160 × 95 mm

Placa Control Fuentes y Carga
edgranzella/Placa-de-Corte-TX
Circuito Impreso de la plaquetita de Corte TX que va apilada sobre el Arduino Nano de la placa Controladora de Fuentes y Carga.
142 parts
Questions
How big is the Power supply2 PCB?
It measures 24.6 × 33.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Power supply2 use?
25 parts, built around the MP2322GQH-Z, 1812L110/33MR, AO3407A and DC-005-2.5A-2.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Power supply2 KiCad files?
From the jrseti/pcbs repository on GitHub, at the commit this page was made from: the board is power_supply2/power_supply2.kicad_pcb and its schematic dishy1pi/DishyPi1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Power supply2 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).