

DishyPi1
Various printed circuit board projects
- Size
- 94.6 × 69.3 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 106
- Nets
- 81
- Pads
- 350
- Tracks, vias
- 0, 0
- Pours
- 13
- Routed
- Not yet
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Mar 2026
- Updated
- 4 Aug 2026
Overview
DishyPi1 is an open-source printed circuit board by jrseti, from the jrseti/pcbs repository on GitHub, published under the MIT licence. It is a 4-layer board of 94.6 × 69.3 mm with 106 parts on 81 nets.
It is built around the TPS561201DDCR, LTV-817S-TA1 and LTV-827S-TA1, with the LTV-847S, CAT24C256WI-GT3 and ISO1540DR-HXY among its other parts. Its parts include 35 resistors, 29 diodes, 13 capacitors, 13 ICs and 7 connectors.
Main components
12TPS561201DDCR
TSOT-23-6-40℃~+125℃ 1 1A 380uA 4.5V~17V 580kHz 760mV~7V Adjustable Buck Buck Built-in Yes TSOT-23-6 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersLTV-817S-TA1
SMD-4P-55℃~+110℃ 1 1.2V 100mV@20mA,1mA 200mW 35V 3us 4us 50% 50mA 50mA 5kV 600% 6V DC Phototransistor SMD-4P Transistor, Photovoltaic Output Optoisolators ROHSLite-OnTransistor, Photovoltaic Output OptoisolatorsLTV-827S-TA1
SMD-8P-30℃~+110℃ 1.2V 100mV@1mA,20mA 2 35V 3us 4us@2mA,100Ω 50% 50mA 50mA 5kV 600% 6V DC Phototransistor SMD-8P Transistor, Photovoltaic Output Optoisolators ROHSLite-OnTransistor, Photovoltaic Output OptoisolatorsLTV-847S
SMD-16P-30℃~+110℃ 1.2V 100mV@1mA,20mA 35V 3us 4 4us@2mA,100Ω 50% 50mA 50mA 5kV 600% 6V DC Phototransistor SMD-16P Transistor, Photovoltaic Output Optoisolators ROHSLite-OnTransistor, Photovoltaic Output OptoisolatorsCAT24C256WI-GT3
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 256Kbit 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHSonsemiEEPROMISO1540DR-HXY
SOP-8SOP-8 I2C Isolators ROHSHXY MOSFETI2C IsolatorsLTC4311ISC6#TRPBF
SC-70-6-40℃~+85℃ 1.6V~5.5V 2 2-Wire Bus 2-Wire Bus Accelerator SC-70-6 Signal Buffers, Repeaters, Splitters ROHSAnalog DevicesSignal Buffers, Repeaters, SplittersTPESD0402G05V
0402-55℃~+125℃ 0.05pF 1 10nA 40V 5V Bidirectional IEC 61000-4-2 0402 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)KF2EDGR-2.54-4P
弯插,P=2.54mm-40℃~+105℃ 1 130V 1x4P 2.54mm 4 4P 5A Board Side/Socket - Closed Green Right-Angle 弯插,P=2.54mm Pluggable System Terminal Block ROHSCixi Kefa ElecPluggable System Terminal BlockKF2EDGR-2.54-6P
弯插,P=2.54mm-40℃~+105℃ 1 130V 1x6P 2.54mm 5A 6 6P Board Side/Socket - Closed Green Right-Angle 弯插,P=2.54mm Pluggable System Terminal Block ROHSCixi Kefa ElecPluggable System Terminal BlockKF2EDGR-2.54-9P
弯插,P=2.54mm-40℃~+105℃ 1 130V 1x9P 2.54mm 5A 9 9P Board Side/Socket - Closed Green Right-Angle 弯插,P=2.54mm Pluggable System Terminal Block ROHSCixi Kefa ElecPluggable System Terminal BlockSMBJ16A
DO-214AA(SMB)16V 19.7V 23.08A 26V 5uA 600W@10/1000us IEC 61000-4-2 TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
README
dishy1pi/README.mdDishy1Pi Hardware
The hardware part of the Dishy1Pi project is a Raspberry Pi Hat board which interfaces the Raspberry Pi GPIO pins with the satellite dish motor controllers, encoders, and various sensors. An important aspect of this board is that the Raspberry Pi is optically isolated from the hardware connected to the satellite dish.
Although this project is tailored to controlling a satellite dish, it can also be used for controlling other motor control systems that require isolation and encoder feedback.
Parts Library
The PCB will be assembled by JCLPCB. The project will require parts number identification to be compatible with LCSC part numbers. See Library README
Parts
106| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | TPESD0402G05V | MyParts:D0402-BI | D10, D11, D12, D13, D14, D15, D16, D17, D18, D20, D21, D22, D23, D24, D25, D26 +8 |
| 12 | 1kΩ | PCM_JLCPCB:R_0402 | R4, R6, R8, R12, R13, R14, R21, R23, R25, R29, R30, R31 |
| 6 | 100nF | PCM_JLCPCB:C_0402 | C3, C5, C6, C7, C8, C11 |
| 6 | 10kΩ | PCM_JLCPCB:R_0402 | R5, R7, R9, R22, R24, R26 |
| 4 | 22kΩ | PCM_JLCPCB:R_0402 | R11, R16, R28, R33 |
| 4 | 4.7kΩ | PCM_JLCPCB:R_0402 | R17, R18, R19, R20 |
| 4 | LTV-817S-TA1 | MyParts:LTV817S | U4, U5, U11, U12 |
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 3 | 10uF | PCM_JLCPCB:C_0805 | C12, C13, C14 |
| 2 | 220Ω | PCM_JLCPCB:R_0402 | R10, R27 |
| 2 | 3.9kΩ | PCM_JLCPCB:R_0402 | R2, R3 |
| 2 | 470Ω | PCM_JLCPCB:R_0402 | R15, R32 |
| 2 | KF2EDGR-2.54-4P | MyParts:CONN-TH_4P-P2.54_KF2EDGR-2.54-4P | CN4, CN5 |
| 2 | KF2EDGR-2.54-6P | MyParts:CONN-TH_KF2EDGR-2.54-6P | CN3, CN7 |
| 2 | KF2EDGR-2.54-9P | MyParts:CONN-TH_9P-P2.54_KF2EDGR-2.54-9P | CN2, CN6 |
| 2 | LTV-827S-TA1 | MyParts:LTV827S-TA1 | U3, U10 |
| 2 | LTV-847S | MyParts:SMD-16_L20.0-W6.5-P2.54-LS10.2-BL | U2, U9 |
| 2 | SMBJ16A | PCM_JLCPCB:D_SMB | D33, D34 |
| 1 | 1.27MM/1*2P | MyParts:HDR-TH_2P-P1.27-V-M | H1 |
| 1 | 100nF | PCM_JLCPCB:C_0805 | C15 |
| 1 | 100nF | PowerSupply:C0603 | C10 |
| 1 | 100pF | PCM_JLCPCB:C_0402 | C4 |
| 1 | 10k | PowerSupply:R0603 | R35 |
| 1 | 1812L110/33MR | PowerSupply:F1812 | F1 |
| 1 | 2.2kΩ | PCM_JLCPCB:R_0402 | R36 |
| 1 | 4.7uH | PowerSupply:IND-SMD_L3.0-W3.0-1 | L1 |
| 1 | 47uF | PowerSupply:C1206 | C9 |
| 1 | 54.9k | PowerSupply:R0603 | R34 |
| 1 | CAT24C256WI-GT3 | MyParts:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U1 |
| 1 | Conn_02x20_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | DC-005-2.5A-2.0 | PowerSupply:CONN-TH_DC-005-2.5A-2.0 | DC1 |
| 1 | ISO1540DR | MyParts:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U7 |
| 1 | LED | LED_SMD:LED_1206_3216Metric | D32 |
| 1 | LM75BIMX-5/NOPB | MyParts:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | U8 |
| 1 | LTC4311ISC6#TRPBF | MyParts:SC-70-6_L2.2-W1.3-P0.65-LS2.2-BL | U6 |
| 1 | SMBJ18A_C78412 | MyParts:SMB_L4.6-W3.6-LS5.3-RD | D30 |
| 1 | SS-12F49-G050 | PowerSupply:SW-TH_SS-12F45-GXXX | SW2 |
| 1 | SS34 | PowerSupply:SMA_L4.3-W2.6-LS5.2-RD | D29 |
| 1 | TPS561201DDCR | PowerSupply:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BR | U13 |
More from jrseti/pcbs
3- 4 layers100 × 100 mm

- 4 layers59.9 × 57.5 mm

- 4 layers24.6 × 33.1 mm

Similar boards
- 4 layers24.6 × 33.1 mm

Power supply2
jrseti/dishy1pi
Satellite dish motor control for Raspberry Pi, hardware and software
21 partsMIT - 4 layers140 × 100 mm

Rcm dish controller
jrseti/Dish
Simple controller with toggle switches to move the dish motors
314 partsCC0-1.0 - 4 layers150 × 100 mm

Cm4-robo controller
jrseti/roboclaw-cm4-dc-dish-controller
Satellite dish controller using a ROBOCLAW-2X15A-OEM controlled by a Raspberry Pi CM4 module. Powered by DC battery.
292 partsMIT - 2 layers160 × 110 mm

Acquedotto test v4 finale
igorilla666/water-controller
Scheda di controllo basata sul modulo Waveshare ESP32-S3-ETH, con ingressi sensore, RS-485, pilotaggio rele, buzzer e alimentazione/protezioni dedicate.
139 parts1CERN-OHL-S-2.0 - 2 layers75 × 70 mm

- 4 layers41 × 149 mm

Air filter controller
ademuri/air-filter-controller
The ESP32-S3 uses 3.3V. I want onboard indicator LEDs, and the option to have offboard LEDs as well. Using addressable WS2812-type LEDs is flexible. These need a 5V supply.
167 parts1 - 2 layers100 × 96 mm

Backlight
jackw01/scanlight
A better light source for scanning color negative film
69 parts397CERN-OHL-W-2.0 - 4 layers137 × 86 mm

Questions
How big is the DishyPi1 PCB?
It measures 94.6 × 69.3 mm and has 4 copper layers, 1.6 mm thick.
What parts does the DishyPi1 use?
106 parts, built around the TPS561201DDCR, LTV-817S-TA1, LTV-827S-TA1 and LTV-847S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DishyPi1 KiCad files?
From the jrseti/pcbs repository on GitHub, at the commit this page was made from: the board is dishy1pi/DishyPi1.kicad_pcb and its schematic dishy1pi/DishyPi1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DishyPi1 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).