
Iaq device
nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

StratosphericBalloonPCB is an open-source printed circuit board by josamue, from the josamue/StratoPi repository on GitHub. It is a 2-layer board of 140 × 140 mm with 41 parts on 75 nets, routed with 291 tracks and 16 vias.
It is built around the BME280. Its parts include 9 connectors and 7 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H1, H2, H3, H4 |
| 1 | AHT10/BMP280 | AHT10:AHT10Breakout | U5 |
| 1 | AddressJumper | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP3 |
| 1 | ArduinoNano3V3 | Module:Arduino_Nano | A1 |
| 1 | BME280 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | CO2Sensor | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J3 |
| 1 | Connect3V3_JMP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP4 |
| 1 | ConnectRX_JMP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP5 |
| 1 | ConnectSCL_JMP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP2 |
| 1 | ConnectSDA_JMP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | DS1307_RTC | DS1307:DS1307 Module | U2 |
| 1 | GPS-Sensor | GY-GPS6MV2:NEOM8N-Breakout | U6 |
| 1 | GeigerCounter | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J5 |
| 1 | GyroMPU6050 | GY-521:GY-521_1 | U3 |
| 1 | I2C-Sen1 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J9 |
| 1 | I2C-Sen2 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J8 |
| 1 | LoRa-Module | SX1278_LoRa:SX1278_LoRa | U7 |
| 1 | MicroSDReader | MicroSDBoard:MicroSDReader | U4 |
| 1 | OzoneSensor | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J2 |
| 1 | PM-Sensor | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J7 |
| 1 | PWR-IN | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | PressureSensor | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | Raspberry Pi | RPI4:RaspberryPi4b | U1 |
The 26 most common of 41 parts.

nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality


New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker


kbx81/ClimateSprinklerController
ESP32-based climate and sprinkler controller for use with ESPHome

crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone


CCHS-Melbourne/ESPlant
Environmental Sensor Plant - solar WiFi gardening/meteorological sensor using ESP8266
It measures 140 × 140 mm and has 2 copper layers, 1.67 mm thick.
41 parts, built around the BME280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the josamue/StratoPi repository on GitHub, at the commit this page was made from: the board is pcb/StratosphericBalloonPCB.kicad_pcb and its schematic pcb/StratosphericBalloonPCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask josamue before reusing the design.