
Onyks iot esp32-monitor power
knonyks/onyks-iot-monitor-power
Power outlet voltage monitoring for energy tracking and safety.

A small ammeter for measuring printed glucose biosensors
NanoAmmeter v2 is an open-source printed circuit board by joeltroughton, from the joeltroughton/nanoAmmeter repository on GitHub. It is a 4-layer board of 20 × 30 mm with 35 parts on 59 nets, routed with 269 tracks and 60 vias.
It is built around the ADS1115IDGS, LTC2055CMS8#PBF and TLV75733PDBV. Its parts include 13 capacitors, 12 resistors, 4 ICs, 3 connectors and 1 diode. It belongs with the STM32 boards of this library.
nanoAmmeter is a small research device designed to measure the voltage applied to, and the current flowing through biological glucose sensors on the order of 10s to 100s of nanoamps.
As glucose is detected by the sensor, its resistance changes. nanoAmmeter measures the current flow through the sensor for later analysis.
The nanoAmmeter is inserted between the biosensor's negative electrode and ground. The voltage drop across a 100kOhm resistor is amplified by a gain of 101 by a very low offset opamp (Analog LTC2055, ± 3 μV) and finally read by a 16-bit ADC (TI ADS1115). With a FSR of 4.096V, this gives us a theoretical current resolution of 12.4 pA.
The voltage applied to the positive side of the biosensor is buffered to the ADC with unity gain for a theoretic voltage resolution of 125 μV.
The ADC is read by a STM32F072 MCU at 128 samples per second where it is fed into a finite impulse response, low pass filter and exported via USB.
Thanks to https://github.com/pms67 for the FIR circular buffer implementation
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C4, C5, C9 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R14, R15, R17 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R5, R6, R7 |
| 3 | 10nF | Capacitor_SMD:C_0603_1608Metric | C3, C7, C14 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C8, C11, C12 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R2, R8 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C6, C10 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 1 | 1Meg | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | ADS1115IDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U2 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | KSC Logo | Eloise_nA_meter:ksclogo | TP1 |
| 1 | LED_BAGR | Eloise_nA_meter:E6C0606RGBC3UDA | D2 |
| 1 | LOGO | LOGO | G*** |
| 1 | LTC2055CMS8 | Package_SO:MSOP-8_3x3mm_P0.65mm | U1 |
| 1 | STM32F072C8Ux | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U5 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J1 |
| 1 | TLV75733PDBV | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | USB_C_Receptacle_USB2.0 | Eloise_nA_meter:Molex_105450-0101 | J3 |

knonyks/onyks-iot-monitor-power
Power outlet voltage monitoring for energy tracking and safety.



Stan-debakker/grap-6TWEA
Daarnaast moest ik ervoor zorgen dat de nieuwe sensoren correct werken. Ik ben gestart met experimenteren via Arduino IDE, zie "codearduinoIDE".


azmat-bilal/bldc_motor_controller_pcb
A Brushless DC Motor controller board. The design is inspired and is compatible with Odrive project (https://github.com/madcowswe/ODriveHardware) except that this one has a single channel.


It measures 20 × 30 mm and has 4 copper layers, 1.6 mm thick.
35 parts, built around the ADS1115IDGS, LTC2055CMS8#PBF and TLV75733PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the joeltroughton/nanoAmmeter repository on GitHub, at the commit this page was made from: the board is Hardware/nanoAmmeter_v2.kicad_pcb and its schematic Hardware/nanoAmmeter_v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask joeltroughton before reusing the design.