Skip to the content
2 layers51 × 30.8 mmAGB E06-10, the printed circuit board in 3D

Replacement PCB for damaged gameboy advance games using the AGB-E06 pcb

Size
51 × 30.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
39
Pads
329
Tracks, vias
943, 99
Pours
14
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
18 Aug 2024
Updated
1 Nov 2024

Overview

AGB E06-10 is an open-source printed circuit board by JimmehhW, from the JimmehhW/AGB-E06-Replacement-PCB repository on GitHub. It is a 2-layer board of 51 × 30.8 mm with 21 parts on 39 nets, routed with 943 tracks and 99 vias.

It is built around the FM18W08-SG and CR16160J. Its parts include 6 capacitors, 5 resistors and 5 ICs. It belongs with the retro computing and games boards of this library.

Main components

2

README

README.md

Read the License!

AGB-E06-Replacement-PCB

Replacement PCB for damaged gameboy advance games using the AGB-E06 pcb

Credits

Thanks to HDR for the symbols and footprints for the board outline, cart bus, mask rom, battery pads and a few ground pads.
His repo can be found here.

General Info

Please note this PCB can only be used as a replacement board for an original game.

Order at 0.8mm and with ENIG, NOT HASL.

SRAM vs FRAM

As a quick note, if your donor board has a working SRAM I would generally reccomend you simply use that and not go out of your way to get a new FRAM chip since a battery save will likely last more than long enough for most people.

This board works with both the original save chip (SRAM) OR a replacement new part, a FM18W08 (FRAM) with the benefit of the FRAM being that a battery is not required to maintain the save. If FRAM is used, do not install a battery and instead populate R5 with a 10k ohm resistor (sized for 0603), this goes between pins 20 and 28 of the FM18W08 to act as a pullup resistor since the functionality of its chip enable pin is inverted compared to the original SRAM.
As a side note, the SRAM/FRAM footprint on the board is sized for the FM18W08 which is slightly smaller than the original SRAM, although I haven't had any trouble getting the original SRAM on.

BOM

DesignatorComponent
C1,C2,C3,C4,C60402 0.1uF
C50603 ?
R10402 1k
R2,R40402 100k
R30402 5k
R50603 10k (FRAM ONLY!)
BT1CR1616 Tabbed
U1harvested (MX23L6406-12C)
U2harvested (BS62LV256SC-70) OR FM18W08
U3harvested (BU9803F)
U4harvested (PST3425)

FRONT BACK

Parts

21
QtyValueFootprintReferences
2100kCapacitor_SMD:C_0402_1005MetricR2, R4
23x3PadNintendoFootprints:3x3mm_PadA2, A3
110kCapacitor_SMD:C_0603_1608MetricR5
1113nFCapacitor_SMD:C_0402_1005MetricC4
1116nFCapacitor_SMD:C_0402_1005MetricC2
1122nFCapacitor_SMD:C_0402_1005MetricC6
1127nFCapacitor_SMD:C_0402_1005MetricC1
1130nFCapacitor_SMD:C_0402_1005MetricC3
11kCapacitor_SMD:C_0402_1005MetricR1
15kCapacitor_SMD:C_0402_1005MetricR3
1??Capacitor_SMD:C_0603_1608MetricC5
1CR1616NintendoFootprints:AGB-CR1616BT1
1CartBrow_LeftHDR_Gameboy:AGB-Cartbrow_LeftA6
1CartBrow_RightHDR_Gameboy:AGB-Cartbrow_RightA7
1CartBusNintendoFootprints:AGB_CartridgeU0
1FM18W08-SGPackage_SO:SOIC-28W_7.5x17.9mm_P1.27mmU2
1MX23L12806-12CNintendoFootprints:AGB-TSOP-II-44_10.16x18.41mm_P0.8mmU1
1~NintendoFootprints:PST4325U4
1~Package_SO:TSSOP-8_3x3mm_P0.65mmU3

Similar boards

  • 2 layers61.6 × 37.8 mmWonderWitch, the printed circuit board in 3D

    WonderWitch

    up-n-atom/WonderWitch

    PTS-0101 Reproduction - Used in the WonderWitch, Judgement Silver Sword, Dicing Knight, and Tenori-On cartridges.

    34 parts13
  • 2 layers100 × 100 mmMain pcb hw5, the printed circuit board in 3D

    Main pcb hw5

    herzmx/cartreader

    A shield for the Arduino Mega that can back up video game cartridges.

    31 parts2GPL-3.0
  • 2 layers100 × 100 mmMain pcb hw5, the printed circuit board in 3D

    Main pcb hw5

    gemarcano/cartreader

    A shield for the Arduino Mega that can back up video game cartridges.

    31 partsGPL-3.0
  • 2 layers51 × 70 mmDMG A04-01, the printed circuit board in 3D

    DMG A04-01

    HDR/NintendoPCBs

    Replacement pcb's for Nintendo games.

    22 parts321
  • 2 layers51 × 60.7 mmDMG GDAN, the printed circuit board in 3D

    DMG GDAN

    Chase-san/NintendoPCB

    Repository with clones of many Nintendo PCB.

    15 parts63
  • 4 layers110.7 × 69.8 mmSgb mbc5 1-4, the printed circuit board in 3D

    Sgb mbc5 1-4

    MouseBiteLabs/Super-Game-Boy-Plus

    A replacement circuit board for improving the Super Game Boy, or for creating a standalone Game Boy game for the SNES.

    95 parts41CC-BY-SA-4.0
  • 4 layers98.6 × 99.4 mmAs11-comp, the printed circuit board in 3D

    As11-comp

    AvalonSemiconductors/gfmpw1-multi-bringup

    Bring-up of GFMPW-1 multi-project submission.

    111 partsApache-2.0
  • 8 layers100 × 65 mmMatrixDrive RevB, the printed circuit board in 3D

    MatrixDrive RevB

    Matrixite/MatrixDrive

    MatrixDrive is a USB-loadable Mega Drive/Genesis cartridge

    143 parts

Questions

How big is the AGB E06-10 PCB?

It measures 51 × 30.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the AGB E06-10 use?

21 parts, built around the FM18W08-SG and CR16160J. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the AGB E06-10 KiCad files?

From the JimmehhW/AGB-E06-Replacement-PCB repository on GitHub, at the commit this page was made from: the board is KiCad files/AGB-E06-10.kicad_pcb and its schematic KiCad files/AGB-E06-10.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the AGB E06-10 design in my own project?

Its repository states no licence, so its author keeps all rights: ask JimmehhW before reusing the design.