Skip to the content
6 layers447.1 × 61 mmClusterGauges, the printed circuit board in 3D

The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

Size
447.1 × 61 mm
Copper layers
6
Thickness
1.6 mm
Parts
202
Nets
115
Pads
682
Tracks, vias
4,491, 367
Pours
4
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
23 Sep 2026
Updated
7 Nov 2026

Overview

ClusterGauges is an open-source printed circuit board by jessiepullaro414, from the jessiepullaro414/Cluster repository on GitHub, published under the MIT licence. It is a 6-layer board of 447.1 × 61 mm with 202 parts on 115 nets, routed with 4,491 tracks and 367 vias.

Its parts include 48 capacitors, 44 resistors, 2 diodes and 1 inductor.

README

brain/README.md

brain: the centre-screen board, the same in every car

The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition wake and sleep control, the private CAN link to the gauges board, the audio codec and its connectors, two USB-C host ports (J17 on USB_2 and, since 2026-11-06, J19 on USB_1; docs/audio-and-usb.md), the MFi daughterboard header, the dial input and the bench headers.

Power (review 2026-11-03, docs/electrical-review.md section 9): the ignition switches the board on through the LM74930's EN pin, and the module's CTRL_PWR_EN_MOCI holds it on while the module is on or suspended. So the key starts the module from any state (it boots whenever VCC appears), and once software powers the module off with the key off, the board draws only the LM74930's 2.5 uA shutdown current. How long to stay suspended before powering off is a software setting.

It started as a copy of display/ (now archive/display-1966/, the 1966 Mustang's one-panel carrier). The panel connector, the panel's bias supply, its polarity jumpers and its backlight driver moved to the panel's own board (panel-tsd/). In their place are two screen ports:

PortRefVideoConnector
AJ4MIPI DSI, 4 lanes + clockHirose FH12-40S, 40 contacts
BJ18LVDS0 + LVDS1 (one single- or dual-link panel)Hirose FH12-50S, 50 contacts

Each port has its own current-limited 5 V switch (U6, U7: TPS2557-Q1, 1.61 to 1.98 A), panel reset / enable / backlight-PWM lines held low until software drives them, an I2C bus, and an analog panel-ID pin. The pin tables and the rules for a panel board are in docs/screen-ports.md, generated from tools/screen_ports.py, which this board and every panel board are built from.

The pairs from the Verdin socket to each port are planned, not autorouted (fan_route.py): straight on F.Cu over the In1 GND plane, 0.16 mm, with GND guard tracks where the socket has a ground pin between pairs and no length difference inside a pair. The autorouter is fenced out of both corridors.

The copper that carries the 5 V rail's real current is planned as well (power_route.py): L1 and the output capacitors onto a bar with four vias into the In3 pour, J1's supply pins onto a bar with two, two at each port switch, a wide SW_5V, and U2's PGND pins to the input capacitors and their own GND vias. So does the battery path, J2 to both of the buck's input pins, and each screen port's 5 V. The rest of +5V carries milliamps and stays autorouted. route_board.py runs ../review/power_sheet.py on each route, which solves the net with its pours as copper sheets, and counts a failure as a failed attempt (2026-11-06, electrical review section 9.5b).

Build: python build_schematic.py, python build_pcb.py, python route_board.py, python ../run_drc.py ClusterBrain.kicad_pcb, python build_bom.py, python ../review/layout_checks.py brain, python ../review/review_netlist.py brain, python ../review/usb1_topology.py. The autorouter varies from run to run, so check layout_checks.py after each route.

127.5 x 95.3 mm since the shrink of 2026-11-06 (section 9.5c of the electrical review). The empty strips behind J4 and J18 are for the ribbons. floorplan.py checks every part against every other, the corner holes and the module's keep-out.

Not known yet: whether the Verdin iMX95 drives DSI and LVDS as two independent screens at once (the i.MX 95 itself can; question 9 in docs/rfq-drafts.md section 2), and Hirose's per-contact rating and contact side for the FH12 (the design assumes 0.5 A).

Parts

202
QtyValueFootprintReferences
6MountingHole_3.2mm_M3MountingHole:MountingHole_3.2mm_M3MH1, MH2, MH3, MH4, MH5, MH6
4100nF VCI decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC17, C18, C19, C20
4120R VLED series (self-calculated for ~15mA at 5V, real LED Vf 3.0-3.4V typ 3.2V per datasheet - AEC-Q200)Resistor_SMD:R_0603_1608MetricR6, R7, R8, R9
2100nF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC6, C7
2100nF VCC decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC13, C40
2100nF VIO decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC14, C41
210uF 50V X7S extra bulk at VIN_PROT (AEC-Q200)Capacitor_SMD:C_1210_3225MetricC59, C60
218k series, tach, 200V (AEC-Q200)Resistor_SMD:R_1206_3216MetricR76, R77
218pF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC4, C5
222uF 16V X7R COUT (AEC-Q200)Capacitor_SMD:C_1210_3225MetricC2, C45
24.7nF SPLIT stabilization (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC16, C42
260R split termination (AEC-Q200)Resistor_SMD:R_0603_1608MetricR41, R42
2BAV99-Q input clamp (AEC-Q101)Package_TO_SOT_SMD:SOT-23D10, D11
11.8k LED series, Left turn arrow (AEC-Q200)Resistor_SMD:R_1206_3216MetricR82
11.8k LED series, Right turn arrow (AEC-Q200)Resistor_SMD:R_1206_3216MetricR83
1100R BL_EN gate resistor (AEC-Q200)Resistor_SMD:R_0603_1608MetricR10
1100R RG, HGATE to the dV/dt capacitor (AEC-Q200)Resistor_SMD:R_0603_1608MetricR89
1100k BL_GATE pull-down, backlights stay off until firmware drives BL_EN (AEC-Q200)Resistor_SMD:R_0603_1608MetricR86
1100k CAN0_EN pull-down, defined state while the MCU resets (AEC-Q200)Resistor_SMD:R_0603_1608MetricR87
1100k CAN0_STB_N pull-down, defined state while the MCU resets (AEC-Q200)Resistor_SMD:R_0603_1608MetricR88
1100k DELAY pull-up to VS: auto-retry (AEC-Q200)Resistor_SMD:R_0603_1608MetricR92
1100k OV topResistor_SMD:R_0603_1608MetricR51
1100k SENDER_BIAS pull-down while the MCU resets (AEC-Q200)Resistor_SMD:R_0603_1608MetricR98
1100k SENDER_EXC_EN pull-down, excitation off while the MCU resets (AEC-Q200)Resistor_SMD:R_0603_1608MetricR94
1100k UV topResistor_SMD:R_0603_1608MetricR53
1100nF 50V CIN at the fused input (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC62
1100nF 50V U12 VS decoupling (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC63
1100nF ADC_BATT smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC31
1100nF ADC_FUEL smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC28
1100nF ADC_OIL smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC29
1100nF ADC_TEMP smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC30
1100nF BOOT cap (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC11
1100nF CCAP (50V)Capacitor_SMD:C_0603_1608MetricC48
1100nF CTMRCapacitor_SMD:C_0603_1608MetricC49
1100nF SENDER_BIAS (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC67
1100nF SENDER_EXC (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC66
1100nF U13 supply (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC70
1100nF VBAT decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC15
110k (AEC-Q200)Resistor_SMD:R_0603_1608MetricR2
110k LPSPI2_SIN pull-down, idle-state definition (AEC-Q200)Resistor_SMD:R_0603_1608MetricR11
110k STB pulldown, normal mode while MCU resets (AEC-Q200)Resistor_SMD:R_0603_1608MetricR40
110k VPULL_EN series (TI R(SER)) (AEC-Q200)Resistor_SMD:R_0603_1608MetricR90
110k battery divider bottom, self-calculated for 9-16V range with transient margin (AEC-Q200)Resistor_SMD:R_0603_1608MetricR20
110k from the VR filter to U13 IN+ (AEC-Q200)Resistor_SMD:R_0603_1608MetricR101
110k pull-up (AEC-Q200)Resistor_SMD:R_0603_1608MetricR1
110nF 50V VPULL output (ESD, AEC-Q200)Capacitor_SMD:C_0603_1608MetricC64
110nF input filter (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC44
110nF input filter, Alternator / charge (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC54
110nF input filter, Brake / parking brake (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC53
110nF input filter, High beam (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC52
110nF input filter, Left turn (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC50
110nF input filter, Oil pressure (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC55
110nF input filter, Right turn (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC51
110nF input filter, tach (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC56
110uF 50V X7R CIN (AEC-Q200)Capacitor_SMD:C_1210_3225MetricC1
111.5k UV bot (cut-off 5.5V)Resistor_SMD:R_0603_1608MetricR54
115k divider bottom (AEC-Q200)Resistor_SMD:R_0603_1608MetricR45
115k divider bottom, Alternator / charge (AEC-Q200)Resistor_SMD:R_0603_1608MetricR71
115k divider bottom, Brake / parking brake (AEC-Q200)Resistor_SMD:R_0603_1608MetricR68
115k divider bottom, High beam (AEC-Q200)Resistor_SMD:R_0603_1608MetricR65
115k divider bottom, Left turn (AEC-Q200)Resistor_SMD:R_0603_1608MetricR59
115k divider bottom, Oil pressure (AEC-Q200)Resistor_SMD:R_0603_1608MetricR74
115k divider bottom, Right turn (AEC-Q200)Resistor_SMD:R_0603_1608MetricR62
115k divider bottom, tach (AEC-Q200)Resistor_SMD:R_0603_1608MetricR78
11k base resistor, dimmer test load (AEC-Q200)Resistor_SMD:R_0603_1608MetricR106
11k coolant temp pull-up to SENDER_EXC, 1206 (AEC-Q200)Resistor_SMD:R_1206_3216MetricR18
11k fuel ADC series (AEC-Q200)Resistor_SMD:R_0603_1608MetricR55
11k fuel pull-up to SENDER_EXC, 1206: a wire shorted to 14.4 V puts 123 mW in it (11mW at a 10R sender) (AEC-Q200)Resistor_SMD:R_1206_3216MetricR16
11k oil ADC series (AEC-Q200)Resistor_SMD:R_0603_1608MetricR56
11k oil pull-up to SENDER_EXC, 1206 (AEC-Q200)Resistor_SMD:R_1206_3216MetricR17
11k temp ADC series (AEC-Q200)Resistor_SMD:R_0603_1608MetricR57
11nF input filter (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC43
11uF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC8
11uF CVS (50V)Capacitor_SMD:C_0805_2012MetricC47
11uF VCC decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC12
11uF X7R (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC3
11uF X7R LDO input (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC58
11uF X7R U11 input (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC65
12.05k OV bot (clamp 29.9V)Resistor_SMD:R_0603_1608MetricR52
12.2uH power XAL5030-222ME (AEC-Q200)Inductor_SMD:L_Coilcraft_XAL5030-XXXL1

The 101 most common of 202 parts.

More from jessiepullaro414/Cluster

4
  • 6 layers127.5 × 95.3 mmClusterBrain, the printed circuit board in 3D

    ClusterBrain

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    195 partsMIT
  • 6 layers178.2 × 105 mmClusterDisplay, the printed circuit board in 3D

    ClusterDisplay

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    172 partsMIT
  • 4 layers447.1 × 51.3 mmCluster, the printed circuit board in 3D

    Cluster

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    80 partsMIT
  • 6 layers75.4 × 52.3 mmClusterPanelTSD, the printed circuit board in 3D

    ClusterPanelTSD

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    41 partsMIT

Similar boards

  • 6 layers98 × 97 mmOvc5, the printed circuit board in 3D

    Ovc5

    osrf/ovc

    the Open Vision Computer

    202 parts207Apache-2.0
  • 6 layers210 × 119 mmClaculator Keypad, the printed circuit board in 3D

    Claculator Keypad

    Robert-Mones/Claculator

    A reverse Polish notation calculator with added features such as comparisons, branching, and custom recursive operators taken from the Clac project from the 15-122 course at Carnegie Mellon University.

    202 parts5
  • 6 layers82.5 × 82.5 mmGps, the printed circuit board in 3D

    Gps

    xDocka15/GNSS_geret

    Dokument popisuje zmeny/upravy v elektronike gnss-geret z 2024 tak aby vznikla jednodoskova prenostitelna verzia.

    201 parts
  • 6 layers200 × 129 mmHiltop backplane brd, the printed circuit board in 3D

    Hiltop backplane brd

    devtank-ltd/kicad_hiltop_63hp_backplane

    This documentation describes Open Hardware and is Licensed under CERN-OHL-W v2.

    201 parts
  • 6 layers110 × 102 mmChip module, the printed circuit board in 3D

    Chip module

    VABISMO/QSSC

    Quantum Solid State Chip - NV DIAMOND . Spin Defect Simulator and hardware controller with Qiskit backend (WIP)

    201 parts1
  • 6 layers69 × 54 mmOpen control board, the printed circuit board in 3D

    Open control board

    variegated-coffee/all-purpose-espresso-controller

    Espresso electronics are usually proprietary affairs with little to no expandability. The purpose of this project is to give everyone an open source alternative with lots of features and flexibility.

    201 parts14CERN-OHL-P-2.0
  • 6 layers108 × 158.8 mmGk, the printed circuit board in 3D

    Gk

    jncronin/gk

    This respository provides PCB schematics, firmware and debugging support for the gkv4 handheld game console and its operating system, gkos. For the original STM32H7S7-based gk, see README-v3.md.

    203 parts79
  • 6 layers90 × 92.5 mmPower, the printed circuit board in 3D

    Power

    SSL-A-Team/electrical

    circuit board design files, gerbers, and circuit analysis

    203 parts6MIT

Questions

How big is the ClusterGauges PCB?

It measures 447.1 × 61 mm and has 6 copper layers, 1.6 mm thick.

What parts does the ClusterGauges use?

202 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ClusterGauges KiCad files?

From the jessiepullaro414/Cluster repository on GitHub, at the commit this page was made from: the board is gauges/ClusterGauges.kicad_pcb and its schematic archive/display-1966/ClusterDisplay.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ClusterGauges design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).