Skip to the content
6 layers85.3 × 51.9 mmThermo, the printed circuit board in 3D

Companion KiCad project for "Thermo", a specialized automotive-grade board: sibling to manifold-pcb and ecu-pcb, same 12V/AEC-Q/engine-bay-rated constraints as the rest of the family, but purpose-built for two specific…

Size
85.3 × 51.9 mm
Copper layers
6
Thickness
1.6 mm
Parts
62
Nets
44
Pads
248
Tracks, vias
983, 96
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
14 Aug 2026
Updated
12 Oct 2026

Overview

Thermo is an open-source printed circuit board by jessiepullaro414, from the jessiepullaro414/Thermo repository on GitHub, published under the MIT licence. It is a 6-layer board of 85.3 × 51.9 mm with 62 parts on 44 nets, routed with 983 tracks and 96 vias.

Its parts include 27 capacitors, 13 resistors, 6 ICs, 5 connectors and 2 diodes.

README

README.md

Thermo — KiCad schematic + PCB

Companion KiCad project for "Thermo", a specialized automotive-grade board: sibling to manifold-pcb and ecu-pcb, same 12V/AEC-Q/engine-bay-rated constraints as the rest of the family, but purpose-built for two specific jobs instead of Manifold's general-purpose Nano-pinout I/O:

  1. Read a real automotive resistive temperature sending unit (a GM-style closed-element NTC sensor, 2-wire isolated, -40°F to 210°F) via a TI ADS1118-Q1 ADC. This board originally targeted a K-type thermocouple instead; the thermocouple front-end (differential input, open-lead detection, cold-junction compensation) was fully removed and replaced with a simple resistive-divider circuit once the sensor choice changed - see build_schematic.py's own comments at the U5/J4 section for the real reasoning and the sensor's real published resistance curve.
  2. Drive one on-board NEMA14-class stepper motor (real chosen motor: StepperOnline 14C19S1504GF5-025RS, 1.5A/phase) via a TI DRV8434A-Q1 driver - current-limited in hardware to match (see R4/R5 in the schematic).

Status

Schematic is fully wired and ERC-clean (only the same 4 expected tool-limitation findings manifold-pcb's own schematic has). The PCB is placed, real-footprint, and routed except for 1 net that needs a quick hand-finish in the KiCad GUI - route_board.py tries several automatic passes and reports exactly which connection is left; everything else is DRC-clean. A real BOM and connector pinout reference (with 3D renders) is published at jessiescars.com/thermo-spec.html.

Why this project exists

I need a thermostatic actuator replacement for my 1972 Alfa Romeo GTV. Thermo reads real engine temperature from an off-board sending unit and drives a small stepper motor in its place - electronic control standing in for a mechanical/wax-based actuator that's original-1972 hard to find good replacement parts for.

How it's built

Same script-driven, kiutils/kicad-cli-verified workflow as manifold-pcb and ecu-pcb: the generator scripts (build_schematic.py, build_pcb.py, route_board.py, run_drc.py) are the source of truth - always regenerate from them, never hand-edit Thermo.kicad_sch/Thermo.kicad_pcb directly. Every real part, pin number, and package on this board was verified against a real manufacturer datasheet, not guessed - see the inline comments in build_schematic.py for the citations (NXP's S32K1xx Reference Manual, TI's ADS1118-Q1/DRV8434A-Q1/LMR33630-Q1/LM74700-Q1/TLV733P-Q1 datasheets, TE/ Deutsch's real DTM06 connector data, Molex's KK-254 datasheet, Phoenix Contact's MKDS datasheet).

Real hardware summary

  • MCU: NXP S32K144 (Arm Cortex-M4F, AEC-Q100), LQFP-64. Only the pins this board actually uses are exposed (LPSPI0 + 4 stepper GPIO + the fixed crystal/SWD/RESET/power set) - not a general-purpose breakout.
  • Temp sensor ADC: TI ADS1118-Q1 (AEC-Q100 Grade 1), VSSOP-10 (DGS0010A, hand-built footprint - see build_u5_footprint.py).
  • Stepper driver: TI DRV8434A-Q1 (AEC-Q100), VQFN-24 (RGE0024N, hand- built footprint with the real 2.45x2.45mm exposed pad - see build_u6_footprint.py; neither of KiCad's two bundled RGE0024 variants had the right EP size for this exact part).
  • Power stage: reused verbatim from manifold-pcb's own proven 12V input-protection + 5V buck + 3.3V LDO circuit (TI LM74700-Q1 ideal-diode reverse-battery protection, LMR33630-Q1 buck, TLV733P-Q1 LDO, Nexperia PMV37ENEA MOSFET).
  • Connectors: a two-part pigtail architecture, not a single connector mounted on the board. Each of J4 (temp sensor)/J5 (stepper)/J6 (power) is a small real board-mount connector (Molex KK-254 / Phoenix Contact MKDS) wired to a short pigtail, with a sealed TE/Deutsch DTM06 connector crimped on the free/outboard end - DTM06 itself turned out to be a wire-to-wire-only part family with no PCB-mount variant in this pin-count range, confirmed directly against TE's own product data before this architecture was finalized.
  • Board: 6-layer (F.Cu / GND plane / signal / signal / +3V3 plane / B.Cu), rounded corners, 4 corner mounting holes (M3). Each IC is placed as a cluster with its own decoupling/boot/charge-pump/crystal parts at its pins (CLUSTERS in build_pcb.py), not scattered by the area packer.

Every assembled part carries an LCSC field in the schematic - the exact part JLCPCB places, with its voltage/current rating in the Value - and export_fab.py builds the JLCPCB BOM/CPL from those fields. The BOM in Thermo_pinout.html predates the 2026-10-02 review below and is out of date.

Regenerating the board

text
python build_schematic.py   # writes Thermo.kicad_sch (+ Thermo.kicad_sym, sym-lib-table)
python build_pcb.py         # writes Thermo.kicad_pcb, unrouted
python route_board.py       # routes it with FreeRouting, pours GND/+3V3 zones
python run_drc.py           # real kicad-cli DRC, human-readable report
python export_fab.py        # Thermo_gerbers.zip + fab_output/Thermo-JLC-BOM.csv / -CPL.csv

Or run the whole pipeline in order with build.py:

text
python build.py                 # full pipeline
python build.py --skip-route    # skip the slow FreeRouting pass

route_board.py's own routing pass is stochastic - it retries automatically several times per run and keeps the best result, but IMPORTANT: only ever run it against a fresh, unrouted board from build_pcb.py. Re-running it against a board that already has zones filled has reliably hung FreeRouting indefinitely in testing (confirmed: the java process sits at flat memory usage with zero output, a real deadlock, not "just needs more time") - if you need to re-route, regenerate from build_pcb.py first.

Setup (one-time, same as manifold-pcb): install a JRE, and download freerouting-2.2.4.jar into tools/. The jar, not the installer - FreeRouting's own docs specify the jar for headless/CLI use. Not committed to this repo (57.8MB, a generic third-party tool, not project source).

Known open items

  • 1 net needs manual routing - route_board.py's output names exactly which one on the run that produced the current Thermo.kicad_pcb.
  • Prototype-grade parts: JLCPCB doesn't stock the -Q1 versions of the ADS1118 or DRV8434A, so the prototype uses the commercial versions (same die, pinout, package). Production should use the -Q1s.
  • No firmware yet: temperature conversion (ratiometric, see below), homing against J7's switch, stall-threshold learning, sensor-fault handling, brownout recovery and holding-current strategy are all unwritten and untested. The board can't replace the wax actuator until homing and recovery are proven on the bench.
  • Thermal budget unmeasured: driver/motor/enclosure temperature at the 1.5A current limit, and whether the lead screw holds position with the driver asleep (no holding current), need bench testing.
  • Order options: choose "Via Covering: Epoxy Filled & Capped" (the 9 thermal vias under U6 are in-pad) and "Confirm Parts Placement: Yes".
  • U1 (S32K144) isn't stocked at JLCPCB: hand-solder it (LQFP-64, 0.5mm pitch) or consign it. Order assembly with "Confirm Parts Placement: Yes" - no per-package rotation corrections are applied to the CPL.

Fixed in the 2026-10-02 pre-fab review

Every IC's pins and support parts were re-checked against the real TI datasheets. Real bugs found and fixed:

  • Crystal shorted: Y1 had OSC_IN on both crystal terminals (a 3225 crystal is pins 1-3 diagonal, 2/4 are the lid). It could never have oscillated.
  • Capacitor voltage ratings: values had no ratings, so JLCPCB matched a 10V cap onto the 12V rail. All parts now carry explicit LCSC numbers.
  • Buck power stage: L1 was matched to a 150mA signal inductor; now a 2.2uH/6A AEC-Q200 part, with TI's specified 2x22uF output and 10uF + 2x 100nF input caps for the 1.4MHz variant.
  • TVS clamp too high: SMCJ33A clamped up to 53V against the buck's 38V abs max; now SMCJ24A.
  • DRV8434A straps: now 1/8 microstep (M0=M1=DVDD) and STL_REP grounded (TI's way to disable stall reporting; it was floating, which isn't allowed). Footprint is now TI's exact land pattern - nothing interpolated.
  • ADC input: 10k series resistor added so a sender wire shorted to 12V can't destroy the ADS1118.
  • Placement: decoupling/boot/charge-pump caps had landed 10-56mm from their ICs; now 2-7mm.

Fixed in the 2026-10-04 follow-up review

  • Real surge margin: buck is now the 60V LMR36015AQRNXRQ1 (genuine AEC-Q100, same footprint), so the weakest part on the 12V rail is the stepper driver at 50V abs max - above SMCJ24A's 38.9V max clamp. TVS is now the AEC-Q101 SMCJ24AQ-13-F.
  • Sender short-to-battery: D2 blocks the R12 back-feed path into +3V3; U5's AIN1 measures the pull-up node, and firmware computes R_sender = 1k x V(AIN0) / (V(AIN1) - V(AIN0)) (ratiometric).
  • Position recovery: J7 home/limit switch input (U1 pin 23), and the driver's STL_MODE/STL_REP now go to U1 (pins 24/39) for stall learning and jam detection.
  • Solid planes: 6-layer stackup; the router may no longer put traces on the GND (In1) or +3V3 (In4) planes.
  • Release gates: route_board.py and run_drc.py exit non-zero on an incomplete or failing board, build.py stops at the first failure, and export_fab.py refuses to write order files unless DRC passes.
  • Firmware scope: the ADS1118-Q1 reads a raw resistive-divider voltage; firmware needs a real NTC resistance-to-temperature lookup/interpolation against the sensor's published curve (see build_schematic.py's J4/U5 comments for the real reference points) - this is new scope, not shared with either sibling project's firmware.

Fixed in the 2026-10-11 BOM check against LCSC

Every LCSC number in the schematic was checked against LCSC's own listing. 27 of 29 matched; two did not:

  • Q1 ordered the wrong MOSFET: C3647059 is a Leiditech part that reuses the name "PMV37ENEA" (100 mOhm RDSon, 3A, 715pF, -55..150C, not AEC-Q101), not the Nexperia part this design was verified against. Now C553095, the genuine Nexperia PMV37ENEAR (49 mOhm, 3.5A, 450pF, -55..175C, AEC-Q101). Stock warning: LCSC and JLCPCB each show only 1 unit of C553095 as of this check. Fine for one prototype; for more boards buy it from DigiKey/Mouser/Farnell and hand-fit it (remove its lcsc= argument so export_fab.py leaves it out of the JLC BOM/CPL), or re-qualify a stocked AEC-Q101 60V SOT-23 N-FET.
  • Y1 was mislabelled, not mis-ordered: C367183 is a Taitien XXDCELNANF-8MHZ (8MHz, 12pF load, 3225 4-pin), exactly what the circuit needs, but the schematic called it a Yangxing X322508MSB4SI. Renamed. Its rated range is only -40..+85C, below the 125C the rest of the family targets, so check it before any engine-bay use.

Parts

62
QtyValueFootprintReferences
4MountingHole_3.2mm_M3MountingHole:MountingHole_3.2mm_M3MH1, MH2, MH3, MH4
322uF X7R 25V 1210 (buck COUT)Capacitor_SMD:C_1210_3225MetricC2, C27, C28
2100nF X7R 50VCapacitor_SMD:C_0603_1608MetricC6, C7
218pF C0G 50VCapacitor_SMD:C_0603_1608MetricC4, C5
11.00k 1% VREF upperResistor_SMD:R_0603_1608MetricR4
11.00k 1% sender pull-upResistor_SMD:R_0603_1608MetricR12
11.50k 1% VREF lower (IFS=1.5A)Resistor_SMD:R_0603_1608MetricR5
1100k 1% FB topResistor_SMD:R_0603_1608MetricR2
1100nF X7R 50V (BOOT)Capacitor_SMD:C_0603_1608MetricC11
1100nF X7R 50V (LM74700 VCAP)Capacitor_SMD:C_0603_1608MetricC10
1100nF X7R 50V (U5 VDD)Capacitor_SMD:C_0603_1608MetricC13
1100nF X7R 50V ADC filterCapacitor_SMD:C_0603_1608MetricC24
1100nF X7R 50V HOME_SW debounceCapacitor_SMD:C_0603_1608MetricC31
1100nF X7R 50V VPULL sense filterCapacitor_SMD:C_0603_1608MetricC30
110k 1% ADC input protectionResistor_SMD:R_0603_1608MetricR13
110k 1% HOME_SW pull-upResistor_SMD:R_0603_1608MetricR15
110k 1% RESET pull-upResistor_SMD:R_0603_1608MetricR1
110k 1% SPI_CS pull-upResistor_SMD:R_0603_1608MetricR11
110k 1% STL_REP pull-upResistor_SMD:R_0603_1608MetricR17
110k 1% VPULL senseResistor_SMD:R_0603_1608MetricR14
110k 1% nFAULT pull-upResistor_SMD:R_0603_1608MetricR6
110nF X7R 50V (U6 VM pin 1)Capacitor_SMD:C_0603_1608MetricC17
110nF X7R 50V (U6 VM pin 8)Capacitor_SMD:C_0603_1608MetricC18
110uF X7R 50V 1210 (U6 VM bulk)Capacitor_SMD:C_1210_3225MetricC19
110uF X7R 50V 1210 (buck CIN)Capacitor_SMD:C_1210_3225MetricC1
115uH 3.8Asat (Bourns SRN6045TA-150M, AEC-Q200)Inductor_SMD:L_Bourns_SRN6045TAL1
11N4148W (VPULL back-feed block)Diode_SMD:D_SOD-123D2
11nF X7R 50V (TRQ_CNT/STL_TH)Capacitor_SMD:C_0603_1608MetricC23
11uF X5R 50VCapacitor_SMD:C_0603_1608MetricC8
11uF X5R 50V (LDO out)Capacitor_SMD:C_0603_1608MetricC3
11uF X5R 50V (VCC)Capacitor_SMD:C_0603_1608MetricC12
120pF C0G 50V (FB feed-forward CFF)Capacitor_SMD:C_0603_1608MetricC29
1220nF X7R 25V (VCP-VM)Capacitor_SMD:C_0603_1608MetricC21
1220nF X7R 50V (buck CHF, VIN pin 10)Capacitor_SMD:C_0603_1608MetricC26
1220nF X7R 50V (buck CHF, VIN pin 2)Capacitor_SMD:C_0603_1608MetricC25
122nF X7R 50V (CPH-CPL)Capacitor_SMD:C_0603_1608MetricC20
124.9k 1% FB bottomResistor_SMD:R_0603_1608MetricR3
1470nF X7R 25V (DVDD)Capacitor_SMD:C_0603_1608MetricC22
147k 1% HOME_SW seriesResistor_SMD:R_0603_1608MetricR16
18MHz 12pF (Taitien XXDCELNANF-8MHZ)Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1ADS1118IDGSR (proto; ADS1118-Q1 for production)TI_DGS0010A_VSSOP-10:TI_DGS0010A_VSSOP-10_3x3mm_P0.5mmU5
1DRV8434ARGER (proto; DRV8434A-Q1 for production)TI_RGE0024N_VQFN-24:TI_RGE0024N_VQFN-24-1EP_4x4mm_P0.5mm_EP2.45x2.45mmU6
1DTM06-2S nickel, 12V input (sealed)TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ6
1DTM06-2S nickel, GM-style resistive temp sender input (sealed)Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ4
1DTM06-2S nickel, home/limit switch input (sealed)Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ7
1DTM06-4S nickel, NEMA14 stepper output (sealed)Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ5
1LM74700-Q1 (AEC-Q100 G1)Package_TO_SOT_SMD:SOT-23-6U3
1LMR36015AQRNXRQ1 60V 400kHz (AEC-Q100)TI_RNX0012C_VQFN-HR:TI_RNX0012C_VQFN-HR-12_2x3mm_P0.5mmU2
1Mini blade holder, 2A Littelfuse 297 fuse (SAE J2077/ISO 8820-3)Fuse:Fuseholder_Blade_Mini_Keystone_3568F1
1NXP S32K144 automotive (AEC-Q100)Package_QFP:LQFP-64_10x10mm_P0.5mmU1
1PMV37ENEA automotive (AEC-Q101)Package_TO_SOT_SMD:SOT-23Q1
1SMCJ24AQ-13-F TVS (AEC-Q101)Diode_SMD:D_SMCD1
1SWD Tag-ConnectConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ2
1TLV73333PQDBVRQ1 3.3V (AEC-Q100 G1)Package_TO_SOT_SMD:SOT-23-5U4
1ferrite 1k@100MHz 2.5A (FBMH3225HM102NT)Inductor_SMD:L_1210_3225MetricL2

Similar boards

  • 6 layers32 × 32 mmBoard latest, the printed circuit board in 3D

    Board latest

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    62 parts397Apache-2.0
  • 6 layers40 × 40 mmPQ ADCS, the printed circuit board in 3D

    PQ ADCS

    nanosatlab/pocat-hw

    IEEE PocketQubes

    62 parts12
  • 6 layers10 × 17.3 mmOpenRX Mono, the printed circuit board in 3D

    OpenRX Mono

    OpenDrone-hw/OpenRX-Mono

    Open-source dual-band ExpressLRS receiver with one LR1121 radio and one U.FL antenna.

    62 parts6CERN-OHL-S-2.0
  • 6 layers72.1 × 65.5 mmFrankfurt eth pic, the printed circuit board in 3D

    Frankfurt eth pic

    grodansparadis/can4vscp-frankfurt-eth

    Frankfurt Ethernet to CAN4VSCP bridge

    62 parts2
  • 6 layers120 × 40 mmCM5CarrierV2, the printed circuit board in 3D

    CM5CarrierV2

    AsadImranRafique/CM5-Carrier-Board-Rev2

    Open-source six-layer Raspberry Pi CM4/CM5 carrier board with USB-C, 25 W PoE, M.2 NVMe, microSD, I2S, and expansion-board connectors.

    62 parts1Apache-2.0
  • 6 layers143.5 × 83.8 mmEic afe, the printed circuit board in 3D

    Eic afe

    jamead/rfsoc-bxb-fe-eic-hw

    Front End amplifier / Filter PCB for EIC testing.

    62 parts1
  • 6 layers72 × 44 mmNes shell, the printed circuit board in 3D

    Nes shell

    TheBadZhang/nes_shell

    NES 掌上游戏机,也不只是游戏机

    62 parts1

Questions

How big is the Thermo PCB?

It measures 85.3 × 51.9 mm and has 6 copper layers, 1.6 mm thick.

What parts does the Thermo use?

62 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Thermo KiCad files?

From the jessiepullaro414/Thermo repository on GitHub, at the commit this page was made from: the board is Thermo.kicad_pcb and its schematic Thermo.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Thermo design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).