Skip to the content
4 layers447.1 × 51.3 mmCluster, the printed circuit board in 3D

The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

Size
447.1 × 51.3 mm
Copper layers
4
Thickness
1.6 mm
Parts
80
Nets
87
Pads
457
Tracks, vias
2,401, 242
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
23 Sep 2026
Updated
7 Nov 2026

Overview

Cluster is an open-source printed circuit board by jessiepullaro414, from the jessiepullaro414/Cluster repository on GitHub, published under the MIT licence. It is a 4-layer board of 447.1 × 51.3 mm with 80 parts on 87 nets, routed with 2,401 tracks and 242 vias.

Its parts include 30 capacitors, 20 resistors, 11 ICs, 4 connectors and 3 transistors.

README

brain/README.md

brain: the centre-screen board, the same in every car

The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition wake and sleep control, the private CAN link to the gauges board, the audio codec and its connectors, two USB-C host ports (J17 on USB_2 and, since 2026-11-06, J19 on USB_1; docs/audio-and-usb.md), the MFi daughterboard header, the dial input and the bench headers.

Power (review 2026-11-03, docs/electrical-review.md section 9): the ignition switches the board on through the LM74930's EN pin, and the module's CTRL_PWR_EN_MOCI holds it on while the module is on or suspended. So the key starts the module from any state (it boots whenever VCC appears), and once software powers the module off with the key off, the board draws only the LM74930's 2.5 uA shutdown current. How long to stay suspended before powering off is a software setting.

It started as a copy of display/ (now archive/display-1966/, the 1966 Mustang's one-panel carrier). The panel connector, the panel's bias supply, its polarity jumpers and its backlight driver moved to the panel's own board (panel-tsd/). In their place are two screen ports:

PortRefVideoConnector
AJ4MIPI DSI, 4 lanes + clockHirose FH12-40S, 40 contacts
BJ18LVDS0 + LVDS1 (one single- or dual-link panel)Hirose FH12-50S, 50 contacts

Each port has its own current-limited 5 V switch (U6, U7: TPS2557-Q1, 1.61 to 1.98 A), panel reset / enable / backlight-PWM lines held low until software drives them, an I2C bus, and an analog panel-ID pin. The pin tables and the rules for a panel board are in docs/screen-ports.md, generated from tools/screen_ports.py, which this board and every panel board are built from.

The pairs from the Verdin socket to each port are planned, not autorouted (fan_route.py): straight on F.Cu over the In1 GND plane, 0.16 mm, with GND guard tracks where the socket has a ground pin between pairs and no length difference inside a pair. The autorouter is fenced out of both corridors.

The copper that carries the 5 V rail's real current is planned as well (power_route.py): L1 and the output capacitors onto a bar with four vias into the In3 pour, J1's supply pins onto a bar with two, two at each port switch, a wide SW_5V, and U2's PGND pins to the input capacitors and their own GND vias. So does the battery path, J2 to both of the buck's input pins, and each screen port's 5 V. The rest of +5V carries milliamps and stays autorouted. route_board.py runs ../review/power_sheet.py on each route, which solves the net with its pours as copper sheets, and counts a failure as a failed attempt (2026-11-06, electrical review section 9.5b).

Build: python build_schematic.py, python build_pcb.py, python route_board.py, python ../run_drc.py ClusterBrain.kicad_pcb, python build_bom.py, python ../review/layout_checks.py brain, python ../review/review_netlist.py brain, python ../review/usb1_topology.py. The autorouter varies from run to run, so check layout_checks.py after each route.

127.5 x 95.3 mm since the shrink of 2026-11-06 (section 9.5c of the electrical review). The empty strips behind J4 and J18 are for the ribbons. floorplan.py checks every part against every other, the corner holes and the module's keep-out.

Not known yet: whether the Verdin iMX95 drives DSI and LVDS as two independent screens at once (the i.MX 95 itself can; question 9 in docs/rfq-drafts.md section 2), and Hirose's per-contact rating and contact side for the FH12 (the design assumes 0.5 A).

Parts

80
QtyValueFootprintReferences
6MountingHole_3.2mm_M3MountingHole:MountingHole_3.2mm_M3MH1, MH2, MH3, MH4, MH5, MH6
4100nF VCI decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC17, C18, C19, C20
4120R VLED series (self-calculated for ~15mA at 5V, real LED Vf 3.0-3.4V typ 3.2V per datasheet - AEC-Q200)Resistor_SMD:R_0603_1608MetricR6, R7, R8, R9
418pF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC4, C5, C23, C24
2100nF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC6, C7
2100nF VCC decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC13, C25
260R split termination (AEC-Q200) - DNP unless bus end-nodeResistor_SMD:R_0603_1608MetricR4, R5
1100R BL_EN gate resistor (AEC-Q200)Resistor_SMD:R_0603_1608MetricR10
1100R SPD_BL_PWM gate resistor (AEC-Q200)Resistor_SMD:R_0603_1608MetricR15
1100R coolant temp pull-up, self-calculated for the sender's 10-300R range (AEC-Q200)Resistor_SMD:R_0603_1608MetricR18
1100k FB divider bottom, self-calculated for 1.28V (AEC-Q200)Resistor_SMD:R_0603_1608MetricR13
1100nF ADC_BATT smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC31
1100nF ADC_FUEL smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC28
1100nF ADC_OIL smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC29
1100nF ADC_TEMP smoothing (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC30
1100nF BOOT cap (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC11
1100nF VBAT decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC15
1100nF VCCIO decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC27
1100nF VIO decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC14
1100nF charge-pump cap (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC10
110k (AEC-Q200)Resistor_SMD:R_0603_1608MetricR2
110k LPSPI2_SIN pull-down, idle-state definition (AEC-Q200)Resistor_SMD:R_0603_1608MetricR11
110k battery divider bottom, self-calculated for 9-16V range with transient margin (AEC-Q200)Resistor_SMD:R_0603_1608MetricR20
110k pull-up (AEC-Q200)Resistor_SMD:R_0603_1608MetricR1
110uF IN cap (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC21
110uF OUT cap, real min 2.2uF per TI's own stability requirement (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC22
110uF X7R (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC1
110uH power (AEC-Q200)Inductor_SMD:L_1210_3225MetricL1
1120R LEDA series (self-calculated, ~15mA at 5V - AEC-Q200)Resistor_SMD:R_0603_1608MetricR14
112MHz (AEC-Q200)Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY2
11uF (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC8
11uF VCC decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC12
11uF VCC1V2 decouple (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC26
11uF X7R (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC3
12.49k (AEC-Q200)Resistor_SMD:R_0603_1608MetricR3
122uF X7R (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC2
14.7nF SPLIT stabilization (AEC-Q200)Capacitor_SMD:C_0603_1608MetricC16
147R fuel pull-up, self-calculated for the sender's 10-73R range (AEC-Q200)Resistor_SMD:R_0603_1608MetricR16
147R oil pressure pull-up, self-calculated for the sender's 10-70R range (AEC-Q200)Resistor_SMD:R_0603_1608MetricR17
149.9k battery divider top, self-calculated for 9-16V range with transient margin (AEC-Q200)Resistor_SMD:R_0603_1608MetricR19
17.32k FB divider top, self-calculated for 1.28V (AEC-Q200)Resistor_SMD:R_0603_1608MetricR12
18MHz (AEC-Q200)Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1Bridgetek BT817AQ automotive (AEC-Q100 G2)Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP4.1x4.1mmU11
1DTM06-2S nickel, 12V input (sealed)TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ1
1DTM06-5S nickel, CAN0 + 3x sender input (sealed)Connector_Molex:Molex_KK-254_AE-6410-05A_1x05_P2.54mm_VerticalJ7
1LM74700-Q1 (AEC-Q100 G1)Package_TO_SOT_SMD:SOT-23-6U3
1LMR33630-Q1 (AEC-Q100 G1)TI_RNX0012C_VQFN-HR:TI_RNX0012C_VQFN-HR-12_2x3mm_P0.5mmU2
1Mini blade holder, 2A Littelfuse 297 fuse (SAE J2077/ISO 8820-3)Fuse:Fuseholder_Blade_Mini_Keystone_3568F1
1NXP S32K144 automotive (AEC-Q100)Package_QFP:LQFP-64_10x10mm_P0.5mmU1
1NXP TJA1043T automotive CAN transceiver (AEC-Q100)Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU5
1PMV37ENEA automotive (AEC-Q101)Package_TO_SOT_SMD:SOT-23Q1
1PMV37ENEA automotive (AEC-Q101) - shared aux-gauge backlight switchPackage_TO_SOT_SMD:SOT-23Q2
1PMV37ENEA automotive (AEC-Q101) - speedo backlight PWM switchPackage_TO_SOT_SMD:SOT-23Q3
1Panox BH021WVC02 - center speedoConnector_FFC-FPC:Amphenol_F32Q-1A7x1-11040_1x40-1MP_P0.5mm_HorizontalJ3
1Raystar RFA401280B-AYW-DNF1 - Battery voltage gaugeConnector_FFC-FPC:Amphenol_F32Q-1A7x1-11018_1x18-1MP_P0.5mm_HorizontalU9
1Raystar RFA401280B-AYW-DNF1 - Coolant temp gaugeConnector_FFC-FPC:Amphenol_F32Q-1A7x1-11018_1x18-1MP_P0.5mm_HorizontalU8
1Raystar RFA401280B-AYW-DNF1 - Fuel level gaugeConnector_FFC-FPC:Amphenol_F32Q-1A7x1-11018_1x18-1MP_P0.5mm_HorizontalU6
1Raystar RFA401280B-AYW-DNF1 - Oil pressure gaugeConnector_FFC-FPC:Amphenol_F32Q-1A7x1-11018_1x18-1MP_P0.5mm_HorizontalU7
1SMCJ33A automotive (AEC-Q101)Diode_SMD:D_SMCD1
1SWD Tag-ConnectConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ2
1TLV733P-Q1 (AEC-Q100 G1)Package_TO_SOT_SMD:SOT-23-5U4
1TPS7A16-Q1 (AEC-Q100 G1)Package_SO:Texas_DGN0008D_VSSOP-8-1EP_3x3mm_P0.65mm_EP2x2.94mm_Mask1.57x1.89mmU10
1ferrite bead (AEC-Q200)Inductor_SMD:L_1210_3225MetricL2

More from jessiepullaro414/Cluster

4
  • 6 layers447.1 × 61 mmClusterGauges, the printed circuit board in 3D

    ClusterGauges

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    202 partsMIT
  • 6 layers127.5 × 95.3 mmClusterBrain, the printed circuit board in 3D

    ClusterBrain

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    195 partsMIT
  • 6 layers178.2 × 105 mmClusterDisplay, the printed circuit board in 3D

    ClusterDisplay

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    172 partsMIT
  • 6 layers75.4 × 52.3 mmClusterPanelTSD, the printed circuit board in 3D

    ClusterPanelTSD

    jessiepullaro414/Cluster

    The Toradex Verdin iMX95 carrier that runs the centre screen, with everything that does not depend on the car or the panel: the 12 V input and surge protection (LM74930-Q1), the 5 V buck, the 1.8 V rail, the ignition…

    41 partsMIT

Similar boards

  • 4 layers60 × 94 mmDaisySeedPedal125b, the printed circuit board in 3D

    DaisySeedPedal125b

    bkshepherd/DaisySeedProjects

    A collection of hardware and software projects based around the Electro-Smith Daisy Seed

    80 parts559MIT
  • 4 layers47 × 27.5 mmSynth, the printed circuit board in 3D

    Synth

    loxodes/vna

    Under development open hardware microwave vector network analyzer

    80 parts205
  • 4 layers49.5 × 54.9 mmOSSI CM2, the printed circuit board in 3D

    OSSI CM2

    transistorgrab/OSSI

    Open Source Solar Inverter - Software, Hardware, Mechanics

    80 parts99MIT
  • 4 layers36 × 43 mmAsac fc rev b, the printed circuit board in 3D

    Asac fc rev b

    victorhook/asac-fc

    asac fc is an rp2040 based flight controller made for FPV drone flying

    80 parts52GPL-3.0
  • 4 layers30 × 31 mmDriver tmc2160-heater, the printed circuit board in 3D

    Driver tmc2160-heater

    calithameridi/corevus

    High-flexibility, low-cost mechatronics controller for 3D printers

    80 parts25
  • 4 layers65 × 56 mmCopilot Lite, the printed circuit board in 3D

    Copilot Lite

    BayLibre/Copilot

    Manage a DUT power and serial through a single USB port, no additional software required.

    80 parts22MIT
  • 4 layers44 × 93 mmVm020-output, the printed circuit board in 3D

    Vm020-output

    mirdej/vmix

    Multichannel modular analog PAL video mixer based on the SYNKIE project

    80 parts21
  • 4 layers93.9 × 51.7 mmPcb5, the printed circuit board in 3D

    Pcb5

    horychen/ProjectEureka

    12 phase motor drive including inverter, microcontroller-mother-board, sensing, communication, DAC, etc.

    80 parts17GPL-3.0

Questions

How big is the Cluster PCB?

It measures 447.1 × 51.3 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Cluster use?

80 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cluster KiCad files?

From the jessiepullaro414/Cluster repository on GitHub, at the commit this page was made from: the board is archive/single-board-s32k144-bt817aq/Cluster.kicad_pcb and its schematic archive/display-1966/ClusterDisplay.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cluster design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).