2 layers54 × 60 mm
2 layers24.5 × 33.5 mm
Infill pcb
JeffreyWangDev/infill-pcb- Size
- 24.5 × 33.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 15
- Nets
- 7
- Pads
- 35
- Tracks, vias
- 44, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Mar 2025
- Updated
- 3 Mar 2025
Overview
Infill pcb is an open-source printed circuit board by JeffreyWangDev, from the JeffreyWangDev/infill-pcb repository on GitHub. It is a 2-layer board of 24.5 × 33.5 mm with 15 parts on 7 nets, routed with 44 tracks and 0 vias.
It is built around the ITR9608-F. Its parts include 4 resistors, 3 capacitors, 2 connectors, 1 IC and 1 diode.
Main components
1Parts
15| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R4 |
| 1 | |||
| 1 | 0.47uf | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 100nf | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 1k | Capacitor_SMD:C_0603_1608Metric | R3 |
| 1 | 300 | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 33uf | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | ITR9608-F | OptoDevice:Everlight_ITR9608-F | U2 |
| 1 | Jam | Connector_Wire:SolderWire-1sqmm_1x03_P5.4mm_D1.4mm_OD2.7mm | J2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | LM3940IMP-3.3_NOPB | Custom:VREG_LM3940IMP-3.3_NOPB | VR1 |
| 1 | Runout | Connector_Wire:SolderWire-1sqmm_1x03_P5.4mm_D1.4mm_OD2.7mm | J1 |
| 1 | ~ | Custom:SW-TH_SHOU-HAN_JL010 | SW1 |
The 14 most common of 15 parts.
Questions
How big is the Infill pcb PCB?
It measures 24.5 × 33.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Infill pcb use?
15 parts, built around the ITR9608-F. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Infill pcb KiCad files?
From the JeffreyWangDev/infill-pcb repository on GitHub, at the commit this page was made from: the board is main.kicad_pcb and its schematic main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Infill pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask JeffreyWangDev before reusing the design.
Similar boards
- 2 layers80.7 × 83.7 mm
- 2 layers27 × 60 mm
OpenFMS
aasmr/openFMS
Open-source filament presence and motion sensor for Klipper 3D printers – includes MCU firmware, PCB design, and 3D printable parts.
41 partsMIT - 2 layers
- 2 layers
- 2 layers80 × 100 mm
Airstream controller
klaus-liebler/self-balancing_robot
hardware and software for a super cheap self balancing robot
77 partsMIT - 2 layers109.4 × 51 mm
- 2 layers66 × 24 mm
Imu rc car encoders
DimitriOnLSD/imu-rc
Gesture-based RC car controller using ESP32-S3, BLE, LSM6DSO IMU, OLED display, and LiPo battery with USB-C charging.
23 parts7MIT