
Displayboard
PyroVision-ThermalCam/Displayboard
Displayboard for the PyroVision thermal camera.

Galvo controller is an open-source printed circuit board by jeffkub, from the jeffkub/esp32-galvo repository on GitHub, published under the MIT licence. It is a 4-layer board of 75 × 95 mm with 136 parts on 116 nets, routed with 864 tracks and 186 vias.
It is built around the CP2104EK, ESP-WROOM-32D and SN74LV1T34DBV, with the LME49724MR, OPA2134UA and PCM3060PW among its other parts. Its parts include 56 capacitors, 44 resistors, 10 ICs, 8 connectors and 5 diodes.
Laser galvo controller board using the ESP32.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 10k | Resistors_SMD:R_0603 | R3, R10, R13, R14, R15, R16, R19, R20, R21, R22, R23, R24, R31, R32, R33, R34 +6 |
| 19 | 10u | Capacitors_SMD:C_0805 | C4, C13, C19, C22, C24, C27, C29, C30, C32, C43, C44, C45, C46, C47, C51, C52 +3 |
| 17 | 0.1u | Capacitors_SMD:C_0603 | C3, C11, C15, C16, C23, C28, C31, C33, C34, C41, C42, C48, C49, C50, C54, C55 +1 |
| 6 | 330p | Capacitors_SMD:C_0603 | C35, C36, C37, C38, C39, C40 |
| 5 | 1k | Resistors_SMD:R_0603 | R1, R11, R12, R25, R26 |
| 5 | 1u | Capacitors_SMD:C_0805 | C1, C2, C5, C6, C18 |
| 4 | 0 | Resistors_SMD:R_0603 | R39, R40, R41, R42 |
| 4 | 22u | Capacitors_SMD:C_1206 | C10, C12, C20, C21 |
| 4 | 8.06k | Resistors_SMD:R_0603 | R27, R28, R29, R30 |
| 3 | Conn_01x03 | Connectors_JST:JST_XH_B03B-XH-A_03x2.50mm_Straight | J2, J7, J8 |
| 2 | 100u | Capacitors_SMD:CP_Elec_6.3x7.7 | C25, C26 |
| 2 | 10n | Capacitors_SMD:C_0603 | C14, C17 |
| 2 | 20k | Resistors_SMD:R_0603 | R37, R38 |
| 2 | 22.1k | Resistors_SMD:R_0603 | R9, R18 |
| 2 | 47k | Resistors_SMD:R_0603 | R43, R44 |
| 2 | BAT54S | TO_SOT_Packages_SMD:SOT-23 | D4, D5 |
| 2 | Jumper_NO_Small | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | JP1, JP2 |
| 2 | LME49724 | Housings_SOIC:SOIC-8-1EP_3.9x4.9mm_Pitch1.27mm | U9, U10 |
| 2 | MMBT2222 | TO_SOT_Packages_SMD:SOT-23 | Q1, Q2 |
| 1 | 124k | Resistors_SMD:R_0603 | R8 |
| 1 | 2.2u | footprint:CLF7045-D | L2 |
| 1 | 3.3u | footprint:CLF7045-D | L1 |
| 1 | 390k | Resistors_SMD:R_0603 | R2 |
| 1 | 4.7u | Capacitors_SMD:C_0805 | C9 |
| 1 | 73.2k | Resistors_SMD:R_0603 | R17 |
| 1 | CP2104 | Housings_DFN_QFN:QFN-24-1EP_4x4mm_Pitch0.5mm | U3 |
| 1 | Conn_01x03 | Connectors_Molex:Molex_KK-6410-03_03x2.54mm_Straight | J3 |
| 1 | ESP-WROOM-32D | footprint:ESP32-WROOM | U4 |
| 1 | GRN | Diodes_SMD:D_0603 | D3 |
| 1 | JS1400BFQ | footprint:JS1400BFQ | SW1 |
| 1 | Micro_SD_Card_Det | footprint:503182-1853 | J4 |
| 1 | NCP1117LP | TO_SOT_Packages_SMD:SOT-223-3_TabPin2 | U7 |
| 1 | OPA2134 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U8 |
| 1 | ORG | Diodes_SMD:D_0603 | D1 |
| 1 | PCM3060 | Housings_SSOP:TSSOP-28_4.4x9.7mm_Pitch0.65mm | U6 |
| 1 | RED | Diodes_SMD:D_0603 | D2 |
| 1 | Red | footprint:RCJ-01x | J5 |
| 1 | SN74LV1T34 | TO_SOT_Packages_SMD:SOT-23-5 | U1 |
| 1 | TPS54295PWP | Housings_SSOP:HTSSOP-16-1EP_4.4x5mm_Pitch0.65mm_ThermalVias | U5 |
| 1 | UG-2832HSWEG02 | footprint:UG-2832HSWEG02 | U2 |
| 1 | USB_OTG | footprint:10118192 | J1 |
| 1 | White | footprint:RCJ-01x | J6 |
The 130 most common of 136 parts.

PyroVision-ThermalCam/Displayboard
Displayboard for the PyroVision thermal camera.

WeBuildAnything/Wireless-Media-Control-Mouse
The IMU sensor uses the MPU6050 library by Electronic Cats.





shaun-lloyd/dev-ardupilot-obal
ArduPi is an open hardware Raspberry Pi hat to run Ardupilot.

CalinRadoni/pax-DLED
Efficiency, hardware control for digital LEDs and Wi-Fi communications - these are just some of the caracteristics of this controller.
It measures 75 × 95 mm and has 4 copper layers, 1.6 mm thick.
136 parts, built around the CP2104EK, ESP-WROOM-32D, SN74LV1T34DBV and LME49724MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jeffkub/esp32-galvo repository on GitHub, at the commit this page was made from: the board is hardware/galvo_controller/galvo_controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).