jdelouche/aPortableInductionHeater1This is a hardware design that can be used to create a portable induction heater.
APortableInductionHeater is an open-source printed circuit board by jdelouche, from the jdelouche/aPortableInductionHeater repository on GitHub. It is a 2-layer board of 160.3 × 50.8 mm with 27 parts on 53 nets, routed with 242 tracks and 17 vias.
It is built around the IRFB4110. Its parts include 4 capacitors, 3 ICs, 2 connectors and 1 resistor.
This is a hardware design that can be used to create a portable induction heater.
The design uses a Texas Instrument C2000 Launchpad with a TMS320F28027 microcontroller and a full bridge MOSFET power stage. The MOSFETs are driven by the UCC27111 which are connected to the microcontroller enhanced PWM.
The power stage is managed through software with a high-frequency PWM ramp-up.
Copyright (C) DELOUCHE-VILPOUX
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 3ohm | Resistors_THT:R_Axial_DIN0617_L17.0mm_D6.0mm_P20.32mm_Horizontal | RH1, RH2, RL1, RL2 |
| 4 | IRFB4110 | ucc27211:TO-220-HeatSinkHoles | QH1, QH2, QL1, QL2 |
| 2 | MA10-1 | J1, J5 | |
| 2 | .022uf | Capacitors_THT:C_Rect_L9.0mm_W4.9mm_P7.50mm_MKT | C1_1, C2_1 |
| 2 | 1uf | Capacitors_THT:C_Rect_L11.5mm_W6.9mm_P10.00mm_MKT | C1_2, C2_2 |
| 2 | Connector2pin | Connectors:bornier2 | Conn1, Conn4 |
| 1 | 0.1u | Capacitors_THT:C_Rect_L9.0mm_W4.9mm_P7.50mm_MKT | C_U3_3 |
| 1 | 100u | Capacitors_THT:CP_Radial_D10.0mm_P5.00mm | C_U3_2 |
| 1 | 10pinJ2 | UCC27211:MA10-1 | Conn2 |
| 1 | 10pinJ6 | UCC27211:MA10-1 | Conn6 |
| 1 | 1u | Capacitors_THT:C_Rect_L11.5mm_W6.9mm_P10.00mm_MKT | C_U3_1 |
| 1 | 3pinJ3 | UCC27211:MA03-1 | Conn3 |
| 1 | 820 | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1 |
| 1 | schTLV1117-33 | TEXAS_SOT223 | U3 |
| 1 | schUCC27211 | UCC27211_SOIC-8_3.9x4.9mm_Pitch1.27mm | U2 |
| 1 | schUCC27211 | UCC27211:UCC27211_SOIC-8_3.9x4.9mm_Pitch1.27mm | U1 |
| 1 | ~ | LEDs:LED_D5.0mm | LED_U3_1 |
It measures 160.3 × 50.8 mm and has 2 copper layers, 1.6 mm thick.
27 parts, built around the IRFB4110. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jdelouche/aPortableInductionHeater repository on GitHub, at the commit this page was made from: the board is kicad/aPortableInductionHeater.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask jdelouche before reusing the design.
Aleksei327/STM32G474-Precision-Lab-Power-Supply
Precision 0–50 V programmable laboratory PSU with 1 mV/1 mA setting steps, hybrid synchronous-buck + linear regulation, STM32G474 control, INA228 metering, and layered hardware protection.
Aleksei327/STM32G474-Power-Charger
Experimental STM32G474-based high-current battery charger and programmable synchronous buck converter. KiCad hardware and STM32CubeIDE firmware.
Aleksei327/ESP32-C5-OBD2-Scanner
DIY dual-CAN OBD2 adapter on Seeed XIAO ESP32-C5 with a Flutter Android app. Working prototype, tested on a Citroën C3 II: full read-only ECU scan, PSA fault codes, live data. Single-sided home-etched KiCad board.
M-S-Ali/raven-i-sentinel
6S - 24V - 20A Battery Management System (BMS) based on TI BQ76925 and Microchip Atmega328P.
Bihyungbetter/exoskeleton
Exoskeleton is a powered lower-limb exoskeleton with six actuated joints — hip flexion, hip abduction, and knee flexion per leg.
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
