4 layers38 × 38 mm
4 layers38 × 38 mm
ReBuster
jbilander/ReBuster7A drop in replacement PCB for the Super Buster chip
- Size
- 38 × 38 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 197
- Pads
- 625
- Tracks, vias
- 1,989, 218
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 18 Nov 2024
- Updated
- 5 Mar 2026
Overview
ReBuster is an open-source printed circuit board by jbilander, from the jbilander/ReBuster repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 4-layer board of 38 × 38 mm with 40 parts on 197 nets, routed with 1,989 tracks and 218 vias.
It is built around the 10M02SCU169I7G, 74LVC2G07GV,125-JSM and SN74CBTD16210DL, with the LM1117-3.3 among its other parts. Its parts include 28 capacitors and 9 ICs. It belongs with the FPGA and CPLD boards of this library.
Main components
4
10M02SCU169I7G
UBGA-169-40℃~+100℃ 110592bit 125 130 2.85V~3.465V 2000 Integrated temperature sensor MAX 10 UBGA-169 Programmable Logic Device (CPLDs/FPGAs) ROHSIntel/AlteraProgrammable Logic Device (CPLDs/FPGAs)
74LVC2G07GV,125-JSM
SOT-23-6-40℃~+125℃ 1.65V~5.5V 2 2 24mA 4uA 74LVC 9.1ns@3.3V,50pF Open-drain Unidirectional SOT-23-6 Buffers, Drivers, Receivers, Transceivers ROHSJSMSEMIBuffers, Drivers, Receivers, Transceivers
SN74CBTD16210DL
SSOP-48-300mil-40℃~+85℃ 4.5V~5.5V Single Supply SSOP-48-300mil Signal Switches, Multiplexers, Decoders ROHSTexas InstrumentsSignal Switches, Multiplexers, Decoders
LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorised
README
README.mdReBuster
A drop-in replacement PCB for the Amiga Super Buster chip
This is WORK IN PROGRESS. If you generate gerbers and order PCBs from this source you are doing so completely at your own risk!.
BOM Rev. 2A
| Reference | Name/Value | Package | Notes |
|---|---|---|---|
| U1 | 10M04SCU169C8G | BGA-169 11.0x11.0mm_Layout13x13 | Max 10 FPGA 10M04SCU169C8G |
| U2 | LM1117-3.3 | SOT-223 | Low-Dropout Linear Regulator 3.3 Volt |
| U3,U5,U6 | SN74CBTD16210 | TSSOP-48 6.1x12.5mm_P0.5mm | 20-BIT FET Bus switch with level shifting, high-speed TTL-compatible. 74CBTD16210DGGR |
| U4 | SN74LVC16245ADGVR | TSSOP-48_4.4x9.7mm_P0.4mm | 16-bit (dual-octal) noninverting bus transceiver SN74LVC16245ADGVR |
| U7 | 74LVC2G07GV | TSOP-6_1.65x3.05mm_P0.95mm | Open Drain noninverting line driver 74LVC2G07GV |
| U8 | Winslow PLCC-84 Plug | PLCC-84 Plug | Optionally use a home made plug (stacked PCBs) |
| U9 | PLCC-84_TH_pin_holes | TH_plug_pins | Pins that could be used with the DIY-plug PCBs rev1d for manual fitting, L8.7mm Aliexpress. |
| RN1, RN2 | CAY16-1002F4LF RES ARRAY 4 Resistors 10k Ω | 1206 | CAY16-1002F4LF |
| C1-3 | Capacitor 10uF | 1206 | |
| C4,C5,C8,C11 | Capacitor 1uF | 0805 | |
| C6,C7,C9,C10 | Capacitor 0.1uF = 100nF | 0805 | |
| C12-C19, C21-C23 | Capacitor 0.01uF = 10nF | 0603 | |
| C20, C24-C28 | Capacitor 0.1uF = 100nF | 0603 | |
| JTAG | SMT Pin Header Male | SMT 2 x 5 Pin 2.0mm pitch |
BOM Rev. 1A
| Reference | Name/Value | Package | Notes |
|---|---|---|---|
| U1 | GW1N-UV9UG169C6/I5 | BGA-169 11.0x11.0mm_Layout13x13 | Gowin FPGA GW1N-UV9UG169 |
| U2 | LM1117-3.3 | SOT-223 | Low-Dropout Linear Regulator 3.3 Volt |
| U3-U6 | SN74CBTD16210 | TSSOP-48 6.1x12.5mm_P0.5mm | 20-BIT FET Bus switch with level shifting, high-speed TTL-compatible. 74CBTD16210DGGR |
| U7 | Winslow PLCC-84 Plug | PLCC-84 Plug | Optionally use a home made plug (stacked PCBs) |
| U8 | PLCC-84_TH_pin_holes | TH_plug_pins | Pins that could be used with the DIY-plug PCBs rev1d for manual fitting, L8.7mm Aliexpress. |
| RN1, RN2 | CAY16A-4701F4LF RES ARRAY 4 Resistors 4.7k Ω | 1206 | CAY16A-4701F4LF |
| C1-3 | Capacitor 10uF | 1206 | |
| C4,C5,C8,C11 | Capacitor 1uF | 0805 | |
| C6,C7,C9,C10 | Capacitor 0.1uF = 100nF | 0805 | |
| C12-C19 | Capacitor 0.01uF = 10nF | 0603 | |
| C20 | Capacitor 0.1uF = 100nF | 0603 | |
| C21-C24 | Capacitor 0.01uF = 10nF | 0603 | |
| JTAG | SMT Pin Header Male | SMT 2 x 5 Pin 2.0mm pitch |
When ordering from JLCPCB select:
Specify Layer Sequence: Yes
L1(Top layer): F_Cu.gbr
L2(Inner layer1): GND_Cu.gbr
L3(Inner layer2): VCC_Cu.gbr
L4(Bottom layer): B_Cu.gbrRemove Order Number:
Specify a locationThis will notify JLC where to put the order number, they will replace the "JLCJLCJLCJLC" silkscreen label.
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 0.01uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C12, C13, C14, C15, C16, C17, C19, C21, C22, C23 |
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C6, C7, C9, C10 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C4, C5, C8, C11 |
| 3 | 0.1uF | ReBuster:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder_extended | C24, C25, C28 |
| 3 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C1, C2, C3 |
| 3 | SN74CBTD16210 | ReBuster:TSSOP-48_6.1x12.5mm_P0.5mm_padLength_1mm | U3, U5, U6 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C26, C27 |
| 2 | 10k | ReBuster:RESCAF80P320X160X60-8N | RN1, RN2 |
| 1 | 0.01uF | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C20 |
| 1 | 10M02SCU169 | ReBuster:BGA-169_11.0x11.0mm_Layout13x13_P0.8mm_Ball0.5mm_Pad0.35mm_NSMD | U1 |
| 1 | 74LVC2G07GV,125 | Package_SO:TSOP-6_1.65x3.05mm_P0.95mm | U7 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.00mm:PinHeader_2x05_P2.00mm_Vertical_SMD | JTAG1 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U2 |
| 1 | PLCC_84_plug | ReBuster:PLCC-84_TH_pin_holes | U9 |
| 1 | PLCC_84_plug | ReBuster:PLCC-84_Plug_P1.27mm_mirrored | U8 |
| 1 | SN74LVC16245ADGVR | ReBuster:TSSOP-48_4.4x9.7mm_P0.4mm_custom | U4 |
Questions
How big is the ReBuster PCB?
It measures 38 × 38 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ReBuster use?
40 parts, built around the 10M02SCU169I7G, 74LVC2G07GV,125-JSM, SN74CBTD16210DL and LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ReBuster KiCad files?
From the jbilander/ReBuster repository on GitHub, at the commit this page was made from: the board is KiCad/ReBuster.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ReBuster design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers38 × 38 mm
ReSDMAC
mbtaylor1982/ReSDMAC
Verilog code to replace the Commodore SDMAC found in the A3000
36 parts51CC-BY-SA-4.0 - 4 layers17.4 × 51.4 mm
- 8 layers120 × 60 mm
Jetson orin baseboard
antmicro/jetson-orin-baseboard
Baseboard targetting the NVIDIA Jetson Orin Nano and Jetson Orin NX
681 parts305Apache-2.0 - 12 layers152.9 × 90 mm
Data center rdimm ddr4-tester
antmicro/rdimm-ddr4-tester
Experimental platform built around Xilinx Kintex-7 FPGA for development and customization of RAM controllers supporting RDIMM DDR4 RAM modules used in data centers.
691 parts32Apache-2.0 - 4 layers79.4 × 58.3 mm
- 8 layers120 × 90 mm
Atlas brain
AtlasAutoware/carv2
Atlas Autoware car v2: drive board (ESC, BMS, USB-C charging), Jetson carrier, printed kit
366 parts - 2 layers33.7 × 97.8 mm
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470