
Meshcore NaIon
Alksndr55/mesh-repeater
Mesh Repeater v1 — одноплатный LoRa-репитер для MeshCore и Meshtastic, 90×100 мм. Упор на максимальное энергосбережение и работу в суровых сибирских зимах. Солнечный зарядник, Na-ion 1S / LTO 2S.

This project integrated hardware, firmware, and software to create a drone controlled by hand motion capture, turning gestures into flight commands.
Drone HW is an open-source printed circuit board by jaoRamalho, from the jaoRamalho/Drone repository on GitHub. It is a 2-layer board of 61.7 × 50.5 mm with 34 parts on 49 nets, routed with 317 tracks and 75 vias.
It is built around the ESP32-WROOM-32D, RC0805FR-0710KL and BC846, with the CL21B104KBCNNNC among its other parts. Its parts include 10 resistors, 6 connectors, 4 capacitors, 3 ICs and 3 diodes. It belongs with the robots and motor control boards and the ESP32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Conn_01x03 | Connector_PinHeader_2.00mm:PinHeader_1x03_P2.00mm_Vertical | J1, J2, J3, J4 |
| 4 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 3 | 10k | Local_Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R14, R25 |
| 3 | 49,9R | Local_Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9, R10, R24 |
| 2 | 10uF/25V | Local_Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2 |
| 2 | 4,7k | Local_Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R11, R12 |
| 2 | BC846 | Local_Package_TO_SOT_SMD:SOT-23 | Q5, Q6 |
| 2 | TVS 3,3V | Local_Package_TO_SOT_SMD:SOT-23 | D4, D6 |
| 1 | 100nF/50V | Local_Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C4 |
| 1 | 15k | Local_Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2 |
| 1 | 220uF/16V | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C3 |
| 1 | 470R | Local_Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32U | U1 |
| 1 | LED | Local_LED_THT:LED_D1.8mm_W3.3mm_H2.4mm | D1 |
| 1 | NRF24L01_Breakout | RF_Module:nRF24L01_Breakout | U3 |
| 1 | STEPDOWN_23V_3V3 | MPU-6050_Module:StepDown3v3_Module | STEP_DOWN1 |
| 1 | Tactile | Local_Button_Switch_THT:SW_TH_Tactile_Omron_B3F-10xx | SW3 |
| 1 | U2 | MPU-6050_Module:MPU6050_Module | U2 |
| 1 | espTool_conn | Local_Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | Con5 |

Alksndr55/mesh-repeater
Mesh Repeater v1 — одноплатный LoRa-репитер для MeshCore и Meshtastic, 90×100 мм. Упор на максимальное энергосбережение и работу в суровых сибирских зимах. Солнечный зарядник, Na-ion 1S / LTO 2S.



SolFV/Clasificador-de-objetos
El proyecto resuelve el control de calidad en líneas de empaquetado mediante un prototipo mecatrónico accesible y modular: una cinta transportadora desplaza cajas frente a una estación de inspección óptica (sensor…

Alksndr55/mesh-repeater-2.0
Mesh Repeater v2 — LoRa-репитер для MeshCore и Meshtastic на платах POWER и LOGIC с экраном SHIELD, 90×60 мм. Упор на максимальное энергосбережение и работу в суровых сибирских зимах.

devkyber/PCB
AI-assisted PCB engineering for native KiCad: source evidence, scoped changes, checked previews, human review, and reproducible release packages.

huulanka/wisp
Open-source ESP32 room climate monitor — CO2, VOC, humidity, temperature and light sensing with custom PCB, MQTT/HomeKit integration, and OTA firmware updates. Full hardware + software, from schematic to BOM.

It measures 61.7 × 50.5 mm and has 2 copper layers, 1.6 mm thick.
34 parts, built around the ESP32-WROOM-32D, RC0805FR-0710KL, BC846 and CL21B104KBCNNNC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jaoRamalho/Drone repository on GitHub, at the commit this page was made from: the board is Hardware/Drone-HW.kicad_pcb and its schematic Hardware/Drone-HW.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask jaoRamalho before reusing the design.