
LogicAnalyzer
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

915 MHz GaAs MMIC Low Noise Amplifier (LNA) PCB built around the Qorvo SPF5189Z. KiCAD design (DRC clean), LTspice bias and supply-filter simulation, planned ADS S-parameter analysis and VNA validation. v2 migration to SPF5043Z planned.
Rf lna is an open-source printed circuit board by Jakcar22, from the Jakcar22/rf-lna repository on GitHub. It is a 2-layer board of 60 × 60 mm with 10 parts on 7 nets, routed with 29 tracks and 79 vias.
Its parts include 4 capacitors, 3 connectors, 2 inductors and 1 IC. It belongs with the radio and wireless and audio and music boards of this library.
A 915 MHz low-noise amplifier printed circuit board built around a Qorvo GaAs pHEMT MMIC, designed as part of a self-directed RF hardware project targeting aerospace and defense applications.
This project takes a commercial GaAs MMIC LNA and builds a complete RF front-end PCB around it: bias network, supply filtering, DC blocking, and 50 Ω microstrip routing. The goal is end-to-end ownership of an RF design from datasheet study through KiCAD layout, simulation, fabrication, and VNA validation.
Version 1 (in this repository): Built around the Qorvo SPF5189Z GaAs MMIC LNA. KiCAD layout complete (DRC clean, ERC clean). LTspice bias and supply-filter simulations complete.
Version 2 (planned): Migration to the Qorvo SPF5043Z GaAs MMIC LNA. The SPF5043Z draws 46 mA versus the SPF5189Z's 90 mA, offering better power efficiency at modest cost in gain. Footprint swap (SOT-363 to SOT-343), trace re-route, and bias network re-simulation are planned.
The SPF5189Z has integrated internal impedance matching, so the external circuit is minimal:
RF IN --[C2 100 pF block]--[L1 1.5 nH match]-- Pin 1 (RF IN)
|
SPF5189Z
|
Pin 3 (RF OUT / DC BIAS) --[C3 100 pF block]-- RF OUT
|
[L2 150 nH RF choke]
|
[C4 100 pF + C1 100 nF bypass]
|
5 V supply
Pin 2, Pin 4 -> GND (with via stitching directly at chip)Pin 3 dual purpose: Pin 3 is both the RF output AND the DC bias input for VDD. The 150 nH inductor acts as an RF choke (passes DC, blocks 915 MHz). The 100 pF cap on the output passes RF while blocking the supply DC from reaching the load.
| Reference | Value | Function |
|---|---|---|
| U1 | SPF5189Z | GaAs MMIC LNA |
| C1 | 100 nF (0.1 µF) | VDD bypass (bulk) |
| C2, C3, C4 | 100 pF | DC blocks on RF input, RF output, VDD |
| L1 | 1.5 nH | Input matching inductor |
| L2 | 150 nH | VDD RF choke |
| J1, J2 | SMA Edge Mount | RF input/output connectors |
| J3 | 1x2 header | 5 V power input |
Verified that the L2 RF choke and C1 bypass capacitor prevent the 915 MHz RF signal from coupling back into the supply line. AC sweep from 1 MHz to 4 GHz, with 1 V AC source representing the worst-case RF leakage into the supply node.
| Frequency | Attenuation at VDD Node |
|---|---|
| 50 MHz | approximately -64 dB |
| 915 MHz | approximately -114 dB |
| 4 GHz | approximately -144 dB |
Result: The supply filter provides approximately 114 dB of RF isolation at the operating frequency. RF signal cannot meaningfully couple back into the power supply, so the bias circuit is stable.
Modeled with V1 = 5 V DC, L2 = 150 nH, R1 = 55.6 Ω (SPF5189Z equivalent chip resistance at 90 mA), C1 = 100 nF bypass.
| Node / Component | Simulated | Expected | Status |
|---|---|---|---|
| V(n001) — VDD node | 5.000 V | 5 V | Pass |
| V(n002) — after RF choke | 4.99991 V | ~5 V | Pass |
| I(R1) — chip bias current | 89.9 mA | ~90 mA | Pass |
| I(L2) — choke current | 89.9 mA | ~90 mA | Pass |
| I(C1) — bypass cap current | ~0 A | 0 A (open at DC) | Pass |
Result: DC bias network delivers 5 V at 90 mA to the chip as specified in the SPF5189Z datasheet.
Planned simulations once the Touchstone (.s2p) model is loaded into ADS via Purdue ECN:
ADS simulation files and output plots are not included in this repository.
Hardware design files (schematics, PCB layouts, BOM, Gerbers) are released under the CERN Open Hardware License Version 2 - Permissive (CERN-OHL-P). Software and documentation are released under the MIT License.
Project in active development. Boards not yet fabricated. Measurements not yet taken. README will be updated as milestones complete.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C3, C4 |
| 2 | Conn_Coaxial | Connector_Coaxial:SMA_Samtec_SMA-J-P-H-ST-EM1_EdgeMount | J1, J2 |
| 1 | 1.5nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 100nf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1 |
| 1 | 150nH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | SPF5189Z | Package_TO_SOT_SMD:SOT-363_SC-70-6_Handsoldering | U1 |

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch


OLIMEX/OLINUXINO
OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
It measures 60 × 60 mm and has 2 copper layers, 1.6 mm thick.
10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Jakcar22/rf-lna repository on GitHub, at the commit this page was made from: the board is rf-lna.kicad_pcb and its schematic rf-lna.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Jakcar22 before reusing the design.