
KM217-WiFi
the78mole/km271-wifi
A piece of hardware to be installed in a Buderus Logamatic 2107 to provide control and status over WiFi

Feather Wing PCB supporting 1-Wire via a DS2484 I2C to 1-Wire master, or selectable jumper for micros that support 1-Wire natively and bit-banging.
1-Wire Wing is an open-source printed circuit board by j3270, from the j3270/1-Wire-Wing-pcb repository on GitHub, published under the MIT licence. It is a 2-layer board of 69.9 × 24.1 mm with 23 parts on 37 nets, routed with 166 tracks and 15 vias.
It is built around the DS2484R+T. Its parts include 9 resistors, 5 switches, 2 capacitors, 2 connectors and 1 IC.
Feather Wing PCB supporting 1-Wire via a DS2484 I2C to 1-Wire master, or selectable jumper for micros that support 1-Wire natively and bit-banging.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | SW_PUSH_SMALL_H | OMRON_PushButtons:OMRON_B3U-1000P | SW1, SW2, SW3, SW4, SW5 |
| 3 | 3.3K | Resistors_SMD:R_0603_HandSoldering | R1, R2, R7 |
| 2 | 10K | Resistors_SMD:R_0603_HandSoldering | R6, R8 |
| 1 | 0.1uF | Capacitors_SMD:C_0603_HandSoldering | C1 |
| 1 | 1K | Resistors_SMD:R_0603_HandSoldering | R4 |
| 1 | 2.2K | Resistors_SMD:R_0603_HandSoldering | R3 |
| 1 | 2uF | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 33K | Resistors_SMD:R_0603_HandSoldering | R9 |
| 1 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03 | JP1 |
| 1 | CONN_01X08 | HIROSE_Connectors:HIROSE_FH19C-8S-0.5SH(05) | CN1 |
| 1 | CONN_01X12 | Pin_Headers:Pin_Header_Straight_1x12 | H3 |
| 1 | CONN_01X16 | Pin_Headers:Pin_Header_Straight_1x16 | H1 |
| 1 | DNI | Resistors_SMD:R_0603_HandSoldering | R5 |
| 1 | DS2484R+ | MaximIntegrated:SOT95P280X125-6N | U1 |
| 1 | FUSE | Capacitors_SMD:C_0603_HandSoldering | F1 |
| 1 | RJ11 | TEConnectivity:TE_6P6C_5555165-1 | J1 |

the78mole/km271-wifi
A piece of hardware to be installed in a Buderus Logamatic 2107 to provide control and status over WiFi



BeeEyeIoT/sensor-station-board
Complete KiCAD project for a sensor data collection station



simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.

csdexter/valhalla
Version-controlled material related to the Valhalla project
It measures 69.9 × 24.1 mm and has 2 copper layers, 1.6 mm thick.
23 parts, built around the DS2484R+T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the j3270/1-Wire-Wing-pcb repository on GitHub, at the commit this page was made from: the board is KiCad/1-Wire_Wing.kicad_pcb and its schematic KiCad/1-Wire_Wing.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).